Dupad Story GSR14G Bluetooth Voice Remote Control
Function Introduction
- Indicator light: Red
- Bluetooth voice remote control
Remote control appearance
Detailed Function Description
IR & BLE Keycode
- Send Bluetooth key code when Bluetooth is connected to the button, and the button does not send infrared key code when Bluetooth is connected (except for the power button)。
- When Bluetooth is not connected, the remote control emits infrared light。
- Press the infrared and Bluetooth status buttons and the LED will flash 5 times (1000ms)。
|
Key Definition |
Usage Page |
Usage ID |
IR Code |
Remarks |
|
Power |
0x000C |
0x0030 |
0x18(0x76) |
1. When Bluetooth is disconnected, a red external code 0x18 appears
2. When connecting via Bluetooth, send the Bluetooth code value first, and after 500ms, send the red external code 0x76 |
|
MENU |
0x0007 |
0x0065 |
0x10 |
|
|
MUTE |
0x000C |
0x00E2 |
0x15 |
|
|
Simulate mouse |
0x5F |
|||
|
UP |
0x0007 |
0x0052 |
0x0D |
|
|
LEFT |
0x0007 |
0x0050 |
0x17 |
|
OK |
0x0007 |
0x0028 |
0x07 |
|
|
RIGHT |
0x0007 |
0x004F |
0x16 |
|
|
DOWN |
0x0007 |
0x0051 |
0x1E |
|
|
BACK |
0x000C |
0x0224 |
0x1F |
|
|
HOME |
0x000C |
0x0223 |
0x80 |
|
|
VOICES |
0x000C |
0x0221 |
/ |
|
|
VOL- |
0x000C |
0x00EA |
0x59 |
|
|
VOL+ |
0x000C |
0x00E9 |
0x55 |
Bluetooth pairing function
| Step | Operation |
| Paired broadcast transmission | Press the “OK” and “Return” buttons on the remote control for more than 3 seconds at the same time, and the indicator light will enter a fast flashing (100ms) state, sending pairing or clearing pairing broadcasts (20s). Broadcast
name LZ MIC RC. |
| Pairing results | When the pairing is successful, the indicator light changes from fast flashing to slow flashing (500ms) and goes off after 2 seconds. If pairing fails, the remote
control indicator light will continue to flash fast for 20 seconds until it goes off. |
Remote control mouse function
Simulate a mouse, press the mouse button to activate the mouse function, press the mouse button again, or do not press the directional key for 30 seconds to turn it off.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and usedbyh the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Documents / Resources
 |
Dupad Story GSR14G Bluetooth Voice Remote Control [pdf] Instruction Manual GSR14G Bluetooth Voice Remote Control, GSR14G, Bluetooth Voice Remote Control, Voice Remote Control, Remote Control, Control |