DUCATI 6203P Rolling Coded Radio Remote Controls
Specifications
- Brand: DUCATI
- Models: 6203ROL, 6203P, 6204
- Technology: Rolling Code Radio Remote Controls
- Power Source:
- 6204 Remote Control: 27A 12V battery
- 6203 Roll Remote Control: 12V type A23-5mA battery
Product Usage Instructions
Remote Control Code Memorisation
- Ensure the garage door or gate is closed before proceeding.
- Memorise the remote control code on the electronic board of your opener by following the specific procedure provided by the manufacturer.
Erasing Remote Control Codes
- Ensure the door is closed and idle.
- Press button P1 on the control board for about 20 seconds until the red LED blinks.
- Release P1 to erase all remote control codes stored in memory.
- Reprogram each remote you wish to use by following the procedure for code memorisation.
Radiocomandi radio rolling code DUCATI
I modelli 6203 rol, 6203P e 6204 sono radiocomandi con codifica radio DUCATI rolling code
- The DUCATI radio rolling coded transmitters, featuring a unique “rolling code” (billions of continuously changing combinations)radio protocol, ensure maximum protection against radio interference.
- Frequency:433,92MHz
- Each transmitter button is factory programmed with a unique code
- Each button can be used to control a different DUCATI rolling coded gate, garage door opener or parking post.
- By adding an external DUCATI rolling coded radio receiver (Rixi 6040 or 6043 with display), it is also possible to control other types of devices of any type and mark by a DUCATI rolling coded remote control.
To operate your “DUCATI” opener with your DUCATI remote control, you must memorise the remote control code on the electronic board of your opener.
WARNING: Operate adjustments and settings only with the garage door or gate in the closed position.
A) To memorise the remote control code inside the electronic panel of the opener:
- The door must be closed and idle.
- Press button P1 on the electronic board. The red LED switches on.
- Release button P1 and immediately press the buttons of the remote control that you wish to use to operate the device. Hold the remote button pressed for about 4secondsc.
- The LED light on the electronic board will quickly blink to show that the procedure has been completed.
- Press again the memorised remote control button, the opener will start an manoever
Warning: The memory of the controller can store up to 10-20 codes depending on the model (check the capacity of your memory card. If you need a larger number of remote controls is available an optional external receiver (RIXY6040 o RIXI6043)
B) To erase the codes from the control board:
To deactivate any unwanted remote, erase its memory from the electronic board of your opener as follows (all remote control codes memorised will be deleted):
- The door must be closed and idle.
- Press button P1 for about 20 seconds. until the red LED blinks
- Release P1.
- All remote control codes have been deleted.- Reprogram each remote you wish to use, following the procedure on point A)
- Remote control PULT 6203 P (100m)
- (Remote control 12bit PULT 6203**)
- Powered by one 12V type A23-5mA battery
IMPORTANT NOTE: Ducati 12-bit Radio remote controls model 6203 are 22-channel1212-bitoded remote controls.
- Each button can be used to control a different DUCATI rolling coded gate, garage door openerand. The coded transmission is a simple 12-bit binary fixed code. 6203 12-bit coded remote controls are compatible only with 12-bit coded electronic boards (12-bit coded electronic board suffix is CTR and not CTH as per rolling coded electronic boards).
- The 12-bit coded remote control model 6203 is very similar to the rolling coded ones, but has transparent push buttons ( sometimes also a transparent case)
While rolling coded radio 6203R is dark blue with dark blue buttons, rolling coded model 6203P (Enhanced Model 100m) is dark blue with red buttons. - Each remote has a standard 112-bit BINARY code.
- STANDARD CODE MEMORIZED ON CHANNEL 1 = push button NAMED “OFF” = ON; OFF,ON;OFF;ON;OFF;ON;OFF,ON, OFF;OFF;ON
- STANDARD CODE MEMORIZED ON CHANNEL 2 = push button NAMED “ON” = OFF; OFF,ON;OFF;ON;OFF;ON;OFF,ON, OFF;OFF;OFF
- A personal code must be programmed to avoid unauthorised commands by other 6203 remotes.
To program a personal code IN YOUR 12 remote CONTROL, follow these steps:
- Simultaneously press the ON and OFF the remote control for about 10 seconds until the LED lights up steadily. From now on, the remote control is in the programming function; release the buttons, and the LED turns off.
- Press for about 1-2 seconds the channel you wish to use to command your device ( ON button = channel 1 ; OFF button = channel 2) ,the LED lights on for about one second.
- Press the buttons (OFF) (ON) making up your string coding to 12 pulses ( it is recommended to previously mark your personal code to be sure have it saved) after each pulse wait until the LED gswitches off.
- On the thirteenth pulse, the remote control will flash to indicate that the programming has been accepted.
To store or delete the electronic card (note: only if series CTR) code, do the above procedureA) AS FOR for the rolling coded remotes.
FAQs
Q: What type of battery powers the 6204 remote control?
A: The 6204 remote control is powered by one 27A 12V battery.
Q: How many channels does the 6203 remote control have?
A: The Ducati 12 bit Radio remote controls model 6203 have 2 channels and are 12 bit coded remote controls.
Documents / Resources
 |
DUCATI 6203P Rolling Coded Radio Remote Controls [pdf] Instruction Manual 6203ROL, 6203P, 6204, 6203P Rolling Coded Radio Remote Controls, 6203P, Rolling Coded Radio Remote Controls, Coded Radio Remote Controls, Radio Remote Controls, Remote Controls |