Dongguan WJZH-M01 Forward and Reverse Remote Control Switch
Forward and reverse remote control switch
Specifications
- Working voltage: DC3V (23032 battery)
- Working current: ≤8MA
- Working temperature: -20°C to +65°C
- Modulation method: ASK
- Operating frequency: 433.925MHz
- Transmission rate: 2Kbit/s
- Transmit power; <1.mw
Product Usage Instructions
- Powering On/Off:
Ensure the device is powered by inserting a DC3V 23032 battery. To power off, remove the battery. - Remote Control:
Use the forward and reverse remote control switch to operate the device. Ensure the operating frequency matches (433.925MHz) for effective control. - Temperature Considerations:
Operate the device within the specified temperature range of -20°C to +65°C to ensure optimal performance and longevity. - Modulation Method:
The device uses the Amplitude Shift Keying (ASK) modulation method for signal transmission. Ensure compatibility with receiving equipment. - Transmission Rate:
The transmission rate of the device is 2Kbit/s, ensuring quick and efficient data transfer.
Remote control
Instantaneous mode: press the upper button of the remote control, the motor will turn forward, andthen the motor will stop after release; press the lower button of the remote control, and the motor wilreverse, and the motor wil stop after release.
Lock mode
Press the up button of the remote control once, the motor will turn forward, press thestop button of the remote control again, the motor will stop, press the down button of the remotecontrol once, the motor wil reverse, press the stop button of the remote control again, the motor willstop.
Remote control pairing method
- Click: Press the study button on the controller once, and the study indicator will flash once and thenturn on. Press the remote control button of “
” again, and the study indicator will flash on three times. Please press the”
“button again, and the study indicator will flash on three times and then turn of. - Interlock: continuous, key secondary controller learning study lamp with flash light, after the second “” a learning remote control button, indicator flashes three times on learning,”
” please pressagain the remote control key, learning after the indicator light flashes three times again bright, again please click “” key, lights flashing three times after learning, learning success.
FCC Statement
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according tod by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The device has evaluated to meet general RF exposure requirement. The device can be used be in portable exposure without restriction.
FAQs
- Q: What should I do if the remote control is not working?
A: Check the battery in the remote control and ensure it is properly inserted. Also, verify that the operating frequency settings match between the remote and the device - Q: Can the device operate outside the specified temperature range?
A: Operating the device outside the specified temperature range (-20°C to +65°C) may result in performance issues or damage to the device. It is recommended to operate within the specified range.
Documents / Resources
 |
Dongguan WJZH-M01 Forward and Reverse Remote Control Switch [pdf] Owner's Manual 2BGW3-WJZH-M01, 2BGW3WJZHM01, WJZH-M01 Forward and Reverse Remote Control Switch, WJZH-M01, Forward and Reverse Remote Control Switch, Reverse Remote Control Switch, Remote Control Switch, Control Switch, Switch |