DOMUS CHAM-TOUCH-3C 3 Channel Wall Controller

Product Information

 

• Product Name: CHAM-TOUCH-3C Wall Controller
• Item Number: 20144
• Type of Controller: RGBW touch wall control
• Output Signal: RF + Bluetooth
• Dimming Range: 0.1% – 100%
• Colour: White (Glass)
• Dimensions (mm): (L) 120 x (W) 75 x (D) 29.1
• Cutout (mm): 19.4
• Transmission Frequency: Not specified
• Operating Temperature: Not specified
• Power Consumption: Not specified
• Operation Voltage: Not specified

Product Usage Instructions

1. 1. Installation:
      • The lamp must be installed by a professional electrician.
      • Ensure the power supply is switched off before fitting this product.
      • Keep away from hot steam and corrosive gas.
   2. Function Introduction:
      • Red channel:
        • Click to turn off/on.
        • Press and hold down to increase/decrease light intensity.
      • Blue channel:
        • Click to turn off/on.
        • Press and hold down to increase/decrease light intensity.
        • Click to select Warm White, Natural White, and Cool White mixed by RGB colors.
        • Press and hold down to increase/decrease light intensity.
      • Green channel:
        • Click to turn off/on.
        • Press and hold down to increase/decrease light intensity.
      • White channel:
        • Click to turn off/on.
        • Press and hold down to increase/decrease light intensity.
        • Click to switch on/off.
        • Click to play/pause the 10 built-in effects.
        • Press and hold down to speed up/down the running effects.
        • Press and hold down to save color/effect.
        • Click to recall the saved color/effect.
   3. Operation:
      • Do wiring the wall panel & RF+Bluetooth receiver according to the wiring diagram provided.
      • Power on, then touch the button to turn on the controller. The indicator of the controller will turn blue.
   4. Pairing with RF+Bluetooth Receiver:
      • Click the Prog. Key on the RF+Bluetooth receiver (or reset power of the receiver 3 times continuously if the button is not accessible) to set it into pairing to RF+Bluetooth remote status.

Variant         Item No.           Detail

20144

CHAM-TOUCH-3C

3CH Wall Controller

Thank you for purchasing your new CHAM-TOUCH-3C Wall Controller, Please take the time to read and understand the instruction sheet below. Failure to do so may void warranty.

Specifications

Type of controller:	RGBW touch wall control	Cutout (mm):	(L) 70mm x (W) 44mm x (D) 20mm
Output signal:	RF + Bluetooth	Transmission frequency:	2.4GHz
Dimming range:	0.1% – 100%	Operating temperature:	0-40°C
Colour:	White (Glass)	Power consumption:	< 15mA
Dimensions (mm):	(L) 120mm x (W) 75mm x (D) 29.1mm	Operation voltage:	240V

• Touch sensitive
• Glass interface(white & black)
• Compatible with all universal series RF+Bluetooth receivers
• Radio frequency: 2.4GHz
• Control RGBW colour
• Control 1 zone/area
• Waterproof grade: IP20

Safety & Warnings

• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.

Function Introduction

Wiring Diagram

Operation

1. Do wiring the wall panel & RF+Bluetooth receiver according to wiring diagram (please refer to the instruction of RF+Bluetooth receiver that you would like to pair with).
2. Power on, then touch the button to turn on the controller, indicator of the controller turned blue.

Pair with RF+Bluetooth receiver

Built-in 10 colour changing modes are as follows:

Mode 1:	Any two colours of RGB mix fade-in & fade-out
Mode 2:	RGB three colours mix fade-in & fade-out
Mode 3:	RGB three colours mix fade-out & fade-in
Mode 4:	RGB flash
Mode 5:	RGB three colours fade-in & fade-out successively
Mode 6:	RGB three colours fade-in successively
Mode 7:	RGB three colours fade-out successively
Mode 8:	RGB three colours jump changing successively
Mode 9:	R&B two colours mix fade (R in B out), then G fade-in, then R&B mix fade (R out B in), then G fade-out
Mode 10:	B fade-out, then G&B mix fade (G out B in), then R&G mix fade (R out G in), then R fade-in

Note

• The lamp must be installed by professional electrician
• Ensure the power supply is switched off before fitting this product
• Do not touch the lamp when in use
• Keep away from hot steam and corrosive gas

Contact

• 29-31 Richland St. Kingsgrove. Sydney NSW 2208 Australia
• Phone: 02 9554 9600
• Fax: 02 9554 9433
• enquiries@domuslighting.com.au
• www.domuslighting.com.au

Documents / Resources

DOMUS CHAM-TOUCH-3C 3 Channel Wall Controller [pdf] Instruction Manual 20144, CHAM-TOUCH-3C 3 Channel Wall Controller, CHAM-TOUCH-3C, 3 Channel Wall Controller, Wall Controller, Controller

References

• User Manual