DiO remote control
Video tutorial
In order to simplify the understanding and installation of our packs and solutions, we have opted for filmed instructions: you can view them on our Youtube.com/c/dio-connec-ted-home channel, in the playlists tab.
Prepare the remote control.
Open the small compartment on the back of the remote control and remove the tab on the battery.
Charging the battery
- Insert a 3/5 mm flathead screwdriver into the small sbtjust the battery compartment and pull the cover to open the compartment.
- Replace the old battery with a new 3V CR2450 battery, making sure the + is facing up.
- Replace the battery compartment until hear a click.
Caution: Danger of explosion if the f battery is replaced correctly. Replace only with the same or equivalent.
- This product contains a button cell battery If the button cell battery is swallowed, it can cause severe internal burns in as little as 2 hours. Keep new and used batteries out of the reach of children.
- If the battery compartment does not close properly, stop using the product and keep it out of reach of h of children. If you suspect that have swallowed or placed inside & a body part, seek medical attention immediately.
As9ciating your remote with a DiO receiver
The DiO Remote Control is compatible with all DiO receivers: switch or module.
Associating the Remote Control with a DiO 1.0 or
DiO Connect receiver
- Connect the mæuk or switch and bring it down to the DiO remote control.
- Put the DiO 1 D or DiO Connect Receiver into learning mode (æe product manual and the LED starts to flash sbslowlyWithin 12 seconds, press the button on the remote control, and the LED on the remote control will flflashapidly for 1 second to confirm the associate ion. Mention: If you do not press the ‘ON’ button on your remote control within 12 seconds, the mæuk/socket will exit learning mode; you must go to ck to point 3.1 for the association.
Deleting the DiO 1 .O receiver remote control
- Bring the control close to the DiO 1 .O modules
- Put the DiO 1 D Receiver into kerning (see product manual), the LED starts to flash slowly.
- Press the ‘v’ button on the channel to delete and, the LED on the remote control flashes rapidly for 1 sec to confirm.
Operation
To open/close
- Press the ‘A’ button to open or the ‘v’ button to close your shutter
To stop the shutter halfway:
- Press the button to stop the shutter when the desired is reached.
- Automatic shut±wn after 2 minutes of continuous use.
Controlling shutters: Up to 5 shutters or groups of shutters can be installed on the DiO remote control. Press the ‘CHAN’ button on the remote control to change channels (channel number confirmed by the number of LEDs on the remote control)Centralizationnbn: The 6th channel automatically centralizes all shutters installing LED channels 1 to 5. Press the CHAN button 6 times the 5 LÜ on the remote flash red once, then press ‘A’ or ivi to all your shutters.
Troubleshooting
- The receiver is not activated when the remote control is pressed:
- Check the ofthe battery and/or thatt it is not flat.
- Make sure that the remote control is linked to the receiver and that the receiver is iconnected&d correctly.
- Check the status of the receiver memory (see receiver manual).
Important
The range remote control is m, but this may be reduced by the thickness of the current environment A minimum distance of 1-2 m is necessary for two DiO receivers (module, socket, and/or bulb). Do not use in a dampbedtimem.
Technical data
- 5463remotete control
- Protocol and frequency
- 433.92 MHz by Di0
- Max. power OS mw ERP
- Range with a DiO 1 .O receiver. 50m (in free field)
- temperatu re: -50 to +400C
- Lithium battery: CR2450 3V (included)
- Number of channels: 3 + 1 group
- Dimensions: 117 x 37 x 9mm
Complete our installation
Complete yoyouryourionn with DiO solutions to control your lighting, your roller shutters your garden or to visualize what is at home with video surveillance. Easy, qualitativescalabl,ebk and economical, discover DiO-connected cited home solutions on www.diohome.com.
Recyclage
- Don’t throw batteries or out-of-order products with the household waste (garbage). The dangerous substances that they are likely to include may harm health or the environment. Make your retailer take back these products or use the selective collection of garbage proposed by your city.
- Hereby, Chacon declares that the radio equipment type 54863 complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.chacon.com/conformity
Documents / Resources
 | 54863 Remote Control |
References
- User Manualmanual.tools
sur ma télécommande les sens d’ouverture et fermeture sont inversé c’est à dire pour monter il faut appuyer sur la flèche descente que faire merci pour la réponse
How do I fix reversed opening and closing directions on my DiO 54863 remote control?
If the opening and closing directions on your DiO 54863 remote control are reversed (e.g., pressing the 'down' arrow makes the shutter go up), this is typically an issue with the wiring of the shutter motor or the receiver module rather than a setting on the remote itself.
To resolve this, you should:
Note: The DiO 54863 remote does not have a software-based 'reverse' function; it simply sends an 'On' signal for the up button and an 'Off' signal for the down button to the receiver.
Read the full Q&A page