Pure Evoke H4

Safety Information

1. Familiarise yourself with all of the safety information and instructions before using the radio.
2. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
3. The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
4. Avoid extreme degrees of temperature, either hot or cold. Place the device well away from heat sources.
5. The mains power adapter is used as the disconnect device and shall remain readily operable.
6. Use only power supplies listed in the user instructions.
7. Ensure that the available supply voltage corresponds with the required operational voltage of the radio.
8. Disconnect your radio from the power supply if you will not use it for a long period of time.
9. Always unplug your radio from the mains socket before cleaning.
10. To reduce the risk of electric shock, do not remove any screws.

ChargePAK F1 Safety Instructions

1. Read the instructions for ChargePAK use in this document.
2. Only use your ChargePAK with original Pure products.
3. Store ChargePAK in a cool, dry place.
4. Do not puncture, modify, drop, throw, or cause other unnecessary shocks to your ChargePAK.
5. Do not dispose of ChargePAK in a fire or incinerator, or leave in hot places.
6. Do not connect ChargePAK directly to an electrical source.
7. Do not immerse ChargePAK in water or otherwise expose it to liquids.
8. Do not short circuit ChargePAK.
9. Do not use or charge a ChargePAK that appears to be leaking, discoloured, rusty, deformed; emitting an odour; or is otherwise abnormal.
10. Do not touch a leaking ChargePAK directly; wear protective material to remove and dispose of it properly immediately.
11. Do not store where children may have access.
12. Dispose of ChargePAK as per normal rechargeable batteries.

Symbols on the product and in the user manual

• ⚠️ Potentially serious risk to your personal safety. Obey all safety notices with this symbol.
• ⓘ Caution. Read the user manual before use.
• ⏻ Where to switch on or off the product, or put it in standby.
• ⚡ 12V DC power supply input, 1.2 amps.
• ? DC connector polarity, the centre of the connector terminal is positive.

Getting started

Your Evoke

Front controls

1 Snoozehandle: Tap to snooze an alarm or brighten the screen when dimmed.

2 Standby: Switch your Evoke H4 on and off, or put it in standby.

3 Volume: Turn to change the volume, press to mute the volume.

4 Timer: Press to set a sleep timer.

5 Alarm: Press to set an alarm or a kitchen timer.

6 Source: Press to change between digital radio, FM radio, Bluetooth, and auxiliary input.

7 Back: Press when in the menu to go back to the previous screen.

8 Menu: Press to change settings and options.

9 Presets: Press to store and access your favourite radio stations.

10 Select: Turn and press to browse radio stations, or select settings and options.

Rear connections

• 12V DC 1.2A: Input for supplied mains adapter only.
• 3.5mm output for stereo headphones: 3.5mm output for stereo headphones.
• Aux in: Analogue stereo input for auxiliary cables.
• Micro USB connector for software updates: Micro USB connector for software updates.

Setting up your Evoke H4

1. Unclip the aerial and fully extend it.
2. Connect the supplied mains adapter to the input on the back of your Evoke H4.
3. Plug the mains adapter into the mains supply.

Switching your Evoke H4 on and off

If you have a ChargePAK rechargeable battery, insert it before you switch your Evoke H4 on. Read more about using a ChargePAK on page 17.

To switch your Evoke H4 on:

• Press ⏻.

Note: When you switch your Evoke H4 on for the first time, it starts tuning to digital radio stations. After the autotune is complete, you can start listening to digital radio.

To switch your Evoke H4 off or put it in standby:

• Press ⏻.

If your Evoke H4 is being powered by a ChargePAK, your Evoke H4 switches off. If your Evoke H4 is connected to a power socket, your Evoke H4 enters standby. In standby, your Evoke H4 uses a low amount of power and displays the time and date on the screen.

Changing the volume

To change the volume:

• To increase the volume, turn the Volume dial clockwise.
• To decrease the volume, turn the Volume dial anticlockwise.

To mute the volume:

• Press the Volume dial.

Digital radio

Listening to digital radio

To listen to digital radio:

• Press ⏻ until 'Digital Radio' is displayed.

Tip: Some digital radio stations also broadcast information and graphics, such as music album artwork or weather updates. Press the Select dial to change between slideshow, large slideshow and display modes.

Changing the digital radio station

To change the digital radio station:

1. Turn the Select dial left or right to browse through the available radio stations.
2. Press the Select dial to change radio station.

Tip: A ‘>>' next to a radio station name means the station has a secondary service. Secondary services may only be available at certain times. A '?' next to a radio station name means the station is inactive or unavailable.

Automatically tuning to digital radio stations

When you switch your Evoke H4 on for the first time, it automatically scans for digital radio stations. If you move your Evoke H4 to a new location, perform an autotune to update the list of radio stations.

To automatically tune to digital radio stations:

1. Press ⚙️.
2. Turn and press the Select dial to choose ‘Autotune'.

Your Evoke H4 starts scanning for digital radio stations.

FM radio

Listening to FM radio

To listen to FM radio:

• Press ⏻ until 'FM' is displayed.

Changing the FM radio station

To change the FM radio station:

• To scan to the previous or next radio station, turn the Select dial left or right and then press the Select dial.
• To manually tune to a radio station, turn the Select dial left or right. The frequency steps up or down by 0.05 MHz.

Changing the scan settings for FM radio

When you scan for FM radio stations, you can include all radio stations or only those with a strong signal.

To change scan settings for FM radio:

1. Press ⚙️.
2. Turn and press the Select dial to choose ‘Scan Setting'.
3. Turn and press the Select dial to choose ‘Strong Stations Only' or 'All Stations'.

Choosing stereo or mono reception for FM radio

By default, your Evoke H4 uses stereo reception for FM radio. If your FM radio stations have a weak signal, try using mono reception to improve the signal strength.

To choose stereo or mono reception:

1. Press ⚙️.
2. Turn and press the Select dial to choose ‘Stereo'.
3. Turn and press the Select dial to choose ‘FM Stereo' or ‘Forced Mono'.

Radio station presets

About presets

You can store your favourite radio stations as presets. You can use presets to quickly tune to your stored radio stations whenever you want.

On the front of your Evoke H4, there are six preset buttons. Use 1 to 5 for quick access to your favourite radio stations. Use 6+ to open a list of all your presets.

You can store up to 20 digital radio stations and up to 20 FM radio stations as presets.

Storing a radio station as a preset

To store a radio station to a preset from 1 to 5:

1. Tune to the radio station you want to store.
2. Choose a preset button from 1 to 5 then press and hold it until a ✔️ is displayed.

Tip: If there is already a radio station stored to the preset you've selected, the new station replaces it.

To store a radio station to the preset list:

1. Tune to the radio station you want to store.
2. Press and hold 6+ until the preset list is displayed.
3. Turn and press the Select dial to choose a preset number. A ✔️ is displayed.

Tip: If there is already a radio station stored to the preset you've selected, the new station replaces it.

Listening to a preset

To listen to a preset from 1 to 5:

• Press a preset button from 1 to 5. For example, to listen to the radio station stored as preset 2, press 2.

To listen to any preset:

1. Press 6+ to open the preset list.
2. Turn and press the Select dial to choose a preset.

Bluetooth and auxiliary devices

Connecting a Bluetooth device

You can use Bluetooth to wirelessly connect to a device, such as a mobile phone or tablet. You can then stream music from your mobile phone or tablet through your Evoke H4.

The first time you connect a Bluetooth device to your Evoke H4, you need to pair them. After you've paired a device with your Evoke H4, your Evoke H4 remembers it for the next time.

To connect a Bluetooth device:

1. Press ⏻ until 'Bluetooth' is displayed.
2. On your Bluetooth device, switch Bluetooth on and connect to your Evoke H4.

Note: For more information, see your Bluetooth device's user manual. If you are asked to enter a passcode, enter 0000.

When 'Connected' is displayed on your Evoke H4 screen, your Evoke H4 is ready to stream music.

Tip: If you want to connect a different Bluetooth device to your Evoke H4, switch off Bluetooth on the connected device first.

Connecting a device with an auxiliary cable

You can use an auxiliary cable to connect a device, such as an MP3 player, to your Evoke H4. You can then enjoy music saved on the device through your Evoke H4.

To connect a device with an auxiliary cable:

1. Press ⏻ until 'Auxiliary Input' is displayed.
2. Insert an auxiliary cable into the Aux in socket on the back of your Evoke H4.
3. Insert the other end of the auxiliary cable into the device you want to connect.

Your Evoke H4 is now ready to play music from the connected device.

Alarms

To wake up to your favourite radio station, you can set up to two alarms on your Evoke H4.

Note: Alarms will not work when your Evoke H4 is being powered by a ChargePAK and off.

Setting an alarm

To set an alarm:

1. Press ⚙️.
2. Turn and press the Select dial to choose 'Alarm 1' or 'Alarm 2'.
3. Turn and press the Select dial to change settings for the alarm:
   • 'Alarm': Turn the alarm on or off
   • 'Frequency': Choose how often you want the alarm to sound
   • 'Wake Up time': Choose the time for the alarm
   • 'Source': Choose to wake up to an FM or digital radio station, or a buzzer. Tip: To choose FM or digital radio, you need to have stored a radio station as a preset.
   • 'Preset': Choose a radio station to wake up to
   • 'Duration': Choose how many minutes the alarm sounds for
   • 'Volume': Choose the volume for the alarm
4. When you have made all of your changes, press ⚙️ to exit the menu.

The ? or ⏰ symbol is displayed at the bottom of the screen when an alarm is set.

Cancelling an existing alarm

To cancel an existing alarm:

1. Press ⚙️.
2. Turn and press the Select dial to choose 'Alarm 1' or 'Alarm 2'.
3. Turn and press the Select dial to change the ‘Alarm' setting to ‘Off’.

Snoozing or silencing an alarm

To snooze an alarm:

• Touch the SnoozeHandle. The alarm snoozes for 5 minutes.

To silence an alarm:

• Press ⏻.

Timers

Setting the kitchen timer

The kitchen timer counts down and then ends with an alarm tone.

To set the kitchen timer:

1. Press ⚙️.
2. Turn and press the Select dial to choose ‘Timer'.
3. Turn the Select dial to choose the duration of the timer.
4. Press the Select dial to start the timer.

The ⏰ symbol is displayed at the bottom of the screen when the timer is set.

Silencing the kitchen timer

To silence the kitchen timer:

• Press ⏻.

Setting the sleep timer

The sleep timer puts your Evoke H4 in standby after a set amount of time.

To set the sleep timer:

1. Press ⚙️.
2. Turn the Select dial to choose the duration of the timer. Tip: You can choose between 15 and 90 minutes.
3. Press the Select dial to start the timer.

The ⏰ symbol and remaining time is displayed at the bottom of the screen when the timer is set.

Settings

Personalising the sound on your Evoke H4

Use the equaliser and boost setting to get the most out of your music. There are several equaliser settings set up already. For example, to hear classical music at its best, change the equaliser setting to ‘Classic'. You can also customise the equaliser to change the treble, bass and loudness.

To use the equaliser:

1. Press ⚙️.
2. Turn and press the Select dial to choose ‘Audio’.
3. Turn and press the Select dial to choose ‘Equaliser'.
4. Choose an equaliser setting:
   • To choose an equaliser setting, turn and press the Select dial.
   • To use custom settings, turn and press the Select dial to choose ‘Custom’. Then turn and press the Select dial to change the treble, bass and loudness.

Display settings

Changing the information displayed on the screen

You can change the information that is displayed on the screen when you are listening to the radio. For example, you can display scrolling information about the current radio station.

To change the information displayed on the screen:

1. Press ⚙️.
2. Turn and press the Select dial to choose 'Display'.
3. Turn and press the Select dial to choose ‘Info’.
4. Turn and press the Select dial to choose the information to display.

Changing the screen brightness

Your Evoke H4 has a light sensor, which adjusts the screen brightness based on your surroundings. You can also manually change the screen brightness. To help save energy, you can dim the screen after 10 seconds of inactivity.

To change the brightness of the screen when switched on:

1. Press ⚙️.
2. Turn and press the Select dial to choose ‘Display'.
3. Turn and press the Select dial to choose ‘On Level'.
4. Turn and press the Select dial to choose a brightness level. To make your screen brighter, choose a higher number. To automatically set the screen brightness, choose ‘Auto’.

To dim the screen after 10 seconds of inactivity:

1. Press ⚙️.
2. Turn and press the Select dial to choose ‘Display'.
3. Turn and press the Select dial to choose ‘Duration'.
4. Turn and press the Select dial to choose ‘Timed'.

To change the brightness of the screen when dimmed:

1. Press ⚙️.
2. Turn and press the Select dial to choose 'Display'.
3. Turn and press the Select dial to choose ‘Dim Level'.
4. Turn and press the Select dial to choose a brightness level. To make your screen brighter, choose a higher number.

Clock settings

Setting the time and date

Your Evoke H4 can use FM and digital radio signals to set the time and date automatically. If the time and date do not update automatically, you can set them manually.

To set the time and date automatically:

1. Press ⚙️.
2. Turn and press the Select dial to choose 'Clock'.
3. Turn and press the Select dial to choose ‘Auto Update'.
4. Turn and press the Select dial to choose how to set the time and date.

To set the time and date manually:

1. Press ⚙️.
2. Turn and press the Select dial to choose 'Clock'.
3. Turn and press the Select dial to choose ‘Set Time/Date'.
4. Turn and press the Select dial to set the date.
5. Turn and press the Select dial to set the time.

Changing the time format

To change the time format:

1. Press ⚙️.
2. Turn and press the Select dial to choose ‘Clock’.
3. Turn and press the Select dial to choose ‘Set 12/24 Hour'.
4. Turn and press the Select dial to choose the time format.

Changing the date format

To change the date format:

1. Press ⚙️.
2. Turn and press the Select dial to choose 'Clock'.
3. Turn and press the Select dial to choose ‘Set Date Format'.
4. Turn and press the Select dial to choose the date format.

Changing the language

You can change the language of menus and settings.

To change the language:

1. Press ⚙️.
2. Turn and press the Select dial to choose 'Settings'.
3. Turn and press the Select dial to choose ‘Language'.
4. Turn and press the Select dial to choose a language.

Resetting to factory settings

A factory reset removes all stored presets, alarms, timers and settings on your Evoke H4.

Note: You cannot undo a factory reset.

To reset to factory settings:

1. Press ⚙️.
2. Turn and press the Select dial to choose 'Settings'.
3. Turn and press the Select dial to choose ‘Factory Reset'.
4. Turn and press the Select dial to choose ‘Yes'.

Your Evoke H4 resets to factory settings and then restarts.

Updating the software

Pure may provide software updates to your Evoke H4. To check for available software updates, visit support.pure.com.

Tip: To be contacted when software updates are available, you can register your product at pure.com/register.

To check the current software version:

1. Press ⚙️.
2. Turn and press the Select dial to choose 'Settings'.
3. Turn and press the Select dial to choose ‘Software Version'.

To update the software:

1. Use a Micro USB cable to connect your Evoke H4 to your computer.
2. Follow the instructions provided with the software update file.

Using a ChargePAK

About ChargePAKs

A ChargePAK is a rechargeable battery pack that allows you to listen to your music anywhere. When your Evoke H4 is connected to a power outlet, it charges the ChargePAK. You can then disconnect your Evoke H4 from the power and take your music with you.

Inserting a ChargePAK

⚠️ Note: Your Evoke H4 is only compatible with a Pure ChargePAK F1. Do not use any other batteries or ChargePAK models with your Evoke H4.

To insert a ChargePAK:

1. Switch your Evoke H4 off and disconnect it from the power supply.
2. At the back of your Evoke H4, press the two clips on the battery cover to remove it.
3. Insert the ChargePAK into the battery compartment, with the electrical contacts on the ChargePAK facing down and the Pure label facing you.
4. Replace the battery cover.
5. Connect your Evoke H4 to the power supply.

The ChargePAK starts charging. If the ChargePAK is new or has not been used for a long time, we recommend you charge it for at least 24 hours.

Note: When the ChargePAK is charging, it is normal for it to get warm. The efficiency of the ChargePAK may decrease over time.

Troubleshooting

Specifications

• Radio: Digital and FM radio
• Frequencies: DAB/DAB+, FM radio 87.5-108MHz
• Bluetooth: v4.1, Frequency range: 2402 < 2480 MHz, Maximum power: 10.00 dBm (EIRP), A2DP support
• Speaker: Full range 3" driver unit
• Audio output power: 10 Watts RMS
• Inputs: 12V DC power adapter socket (230V supplied), 3.5mm stereo Aux In for auxiliary devices, USB connection (Micro USB) for software updates only
• Outputs: 3.5mm stereo headphone
• Presets: 20 digital radio and 20 FM radio presets
• Display: 2.8" colour display
• Software version: v1RC5
• Mains power adapter: Adapter, Input AC 100-240V~, 50/60 Hz, 0.8A, Output DC 12V ---, 1200mA
• ChargePAK: Pure ChargePAK F1 rechargeable battery pack (available separately)
• Power consumption: Standby: 0.8W, Active: 4.5W
• Dimensions: 180mm high x 221mm wide x 128mm deep
• Aerial: Captive telescopic aerial
• Approvals: CE marked. Pure International Ltd declares compliance with essential requirements of RED, 2014/53/EU. Declaration of Conformity at: http://www.pure.com/about/red

Warranty Information

Pure International Limited warrants to the end user that this product will be free from defects in materials and workmanship for two years from the date of purchase. This guarantee covers breakdowns due to manufacturing or design faults; it does not apply in cases such as accidental damage, wear and tear, negligence, adjustment, modification or repair not authorised by Pure International Limited. Should you have a problem with your unit please contact your supplier or contact Pure Support at http://support.pure.com.

Disclaimer

Pure International Limited makes no representation or warranties with respect to the content of this document and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Pure International Limited reserves the right to revise this publication and to make changes in it from time to time without obligation to notify any person or organization of such revisions or changes.

Trademarks

Evoke, Evoke H4, Pure, the Pure logo are trademarks or registered trademarks of Pure International Limited.

Copyright

Copyright © 2017 Pure International Limited. All rights reserved. No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language, in any form or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express written permission of Pure International Limited.

Correct disposal of this product

♻️ This marking indicates that this product should not be disposed with other household waste throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection system or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.