Danfoss ECL Comfort 310 Electronic Controller
Specifications
- Product: ECL Comfort 310
- Model: P314
- Manufacturer: Danfoss
- Input: 24 V a.c.
- Control Interface: 3-point and 0-10 V
Installation
- Follow the provided installation guide for proper setup.
- Ensure the device is connected to a 24 V a.c. Power source.
Configuration
- Use the control interface to set up the desired control parameters.
- Adjust settings such as M1, M2, and M3 based on your requirements.
Operation
- Power on the device using the designated power switch.
- Monitor the display for any alerts or notifications.
Installation Guide
ECL Comfort 310, P314 (code no. 087H3841)
P314.4, ex. a:
P314.4, ex. b:
P314.5, ex. a:
P314.5, ex. b:
P314.6, ex. a:
P314.6, ex. b:
P314.7, ex. a:
P314.7, ex. b:
P314.8, ex. a:
P314.8, ex. b:
P314.10, ex. a:
P314.10, ex. b:
P314.11, ex. a:
P314.11, ex. b:
ECL 310, 24 V a.c..:
ECL 310, 24 V a.c..:
24 V a.c., P314:
24 V a.c., P314
24 V a.c., P314
ECA 32
ECA 32
Example:
24 V a.c. , safety thermostat
1-step closing
2-step closing
Pt 1000 (1000 / 0 °C)
S9 / S10
ECA 32
ECA 32
ECA 32, P314.10, P314.11
S15
ECA 32, P314.4, P314.5, P314.6, P314.7, P314.10, P314.11
S17
ECA 30 / 31
Master/slave
Modbus
M-bus
Pt 1000 (IEC 751B, 1000 Ω / 0 °C
ECA 30
- ECL Comfort 310, P314: www.heating.danfoss.com
- https://www.youtube.com/user/DanfossHeating
- -> Playlists -> How-to Videos -> District Energy installation videos
Danfoss A/S
- Heating Segment • danfoss.com • +45 7488 2222 • E-Mail: heating@danfoss.com
- Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other printed material.
- Danfoss reserves the right to alter its products without notice.
- This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed.
- All trademarks in this material are the property of the respective companies. Danfoss and all Danfoss logotypes are trademarks of Danfoss A/S. All rights reserved.
- 24 | o Danfoss I DHS-SMDT/DK | 2020.12
- AN14678647232500-000401
FAQs
- Q: What is the input voltage for the ECL Comfort 310?
A: The input voltage for the ECL Comfort 310 is 24 V a.c. - Q: How do I configure the control interface?
A: Use the provided guidelines to adjust settings such as M1, M2, and M3 for optimal performance. - Q: What should I do if I encounter an error code on the display?
A: Refer to the user manual for error code explanations and troubleshooting steps.
Documents / Resources
 |
Danfoss ECL Comfort 310 Electronic Controller [pdf] Installation Guide ECL Comfort 310, ECL Comfort 310 Electronic Controller, Electronic Controller, Controller |
 |
Danfoss ECL Comfort 310 Electronic Controller [pdf] Installation Guide ECL Comfort 310, ECL Comfort 310 Electronic Controller, Electronic Controller, Controller |
 |
Danfoss ECL Comfort 310 Electronic Controller [pdf] Installation Guide ECL Comfort 310, ECL Comfort 310 Electronic Controller, Electronic Controller, Controller |