CYCPLUS M3 GPS Bike Computer 
GPS Location – Quick Start Guide
* To receive satellite signals, please remain static and make sure your device is used in an open and unobstructed area. For a faster GPS fix, connect this device to the CYCLUS Fit app and download the ephemeris data before riding.
Specifications
About Buttons
The button functions in normal use are as follows. Please refer to the settings instructions for button operations in the settings.
Data Display
This device has 4 data pages, which can be easily accessed by short-pressing the R1 button.
The data displayed with the factory settings is as follows:
The upper section of the screen displays fixed data fields that cannot be customized. The display content on each page is as follow:
Clock: Displays the current time, with the option to set the time zone in the settings.
Recording Status: No symbol No trip recording in progress.
Speed Unit: Choose between metric (KMH) or imperial (MPH) units in the settings. This will also affect distance and elevation gain/loss display.
Each page displays 4 customizable data fields in the lower half of the screen. You can customize these fields using the CYCPLUS Fit app.
About Settings
For quick setup, open the CYCLUS Fit app to connect and configure the device. Or use buttons to set the device as follows:
- Long press [R1 button =] to enter settings.
- Short press [R1 button = ] to cycle through 8 setting pages.
Long press [R1 button = ] to return to the home page after finishing.
ANT+ Sensors Connection
- Press the L button to start searching for ANT+ sensors.
- When the search starts, the device will check for four types of sensors: speed, heart rate, power, and cadence. If a sensor is detected, its data will be displayed. If no sensor is found, a horizontal line will appear in its place.
- The device will return to the home page after 10 seconds.
Unpair The Paired Sensors
- Go to the C9 page in the settings menu. Press the L button to unpair all connected sensors.
Wheel Circumference Setting
Time Zone Setting
Speed Unit Setting
Temperature Unit Setting
Factory Reset
Odograph Setting
APP Connection
Download and use the CYCLUS Fit APP, which can help you to use this device more conveniently and provides additional support. Scan the QR code or search for “CYCPLUS Fit” on Google Play or the App Store to download the app
Notes
- Data recording:
Long-press the L button to power on the device, then press the L button to start recording the trip. Long-press the R2 button to save the record after finished the ride. The device will save the current record when it shuts down. - Memory: Once the memory is full, the device will overwrite previous records in chronological order.
- Backlight:
After setting the time zone, the screen backlight will automatically turn on from 18:00 to 09:00 each day. When the button is pressed, the backlight will turn on and turn off after 10 seconds.
Package List
About Installation
- CYCPLUS Z1/Z3 bike mount
(Sold separately) - Use the standard bike computer mount
Cross-fix the mount with rubber bands.
Manufacturer Information
- Company: Chengdu Chendian Intelligent Technology Co., Ltd.
- Address: No. 88 Tianchen Road, Chengdu, Sichuan Province, China.
- Warranty: Free repair or replacement within 2 years for non-user-induced damage.
- Contact: steven@cycplus.com
Tire Circumference Chart
Please use this chart for your reference. Tire size is shown on the side of a tire. Tire circumference may vary depending on tire pressure
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
FAQ
- Q: Can this device be used in any location?
- A: Yes, the device can be used in portable exposure conditions without restriction.
- Q: What should I do if I encounter interference issues?
- A: To address interference problems, try reorienting or relocating the antenna, increasing separation between devices, or consulting a professional for assistance.
Documents / Resources
 |
CYCPLUS M3 GPS Bike Computer [pdf] User Manual M3, M3 GPS Bike Computer, GPS Bike Computer, Bike Computer, Computer |
 |
CYCPLUS M3 GPS Bike Computer [pdf] User Manual M3 GPS Bike Computer, M3, GPS Bike Computer, Bike Computer, Computer |
 |
CYCPLUS M3 GPS Bike Computer [pdf] User Manual M3 GPS Bike Computer, M3, GPS Bike Computer, Bike Computer, Computer |