CyberView CV-S101 Combo KVM Extender
Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. We are not liable for any injury or loss that results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
- Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
- Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with temperatures not exceeding 40º Celsius (104º Fahrenheit).
- When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing damage to other equipment or injury to persons nearby.
- When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the power supply. Proper air convection is necessary to keep it from overheating.
- Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
- If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current labeled on the equipment’s electrical ratings label. The
- voltage rating on the cord should be higher than the one listed on the equipment’s ratings label.
Observe all precautions and warnings attached to the equipment. - If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being damaged by transient over-voltage.
- Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power supply or on other hardware may cause damage, fi re or electrical shock.
- Only qualifi ed service personnel should open the chassis. Opening it yourself could damage the equipment and invalidate its warranty.
- If any part of the equipment becomes damaged or stops functioning, have it checked by qualifi ed service personnel.
What the warranty does not cover
- Any product, on which the serial number has been defaced, modifi ed or removed.
- Damage, deterioration or malfunction resulting from:
- Accident, misuse, neglect, fi re, water, lightning, or other acts of nature, unauthorized product modifi cation, or failure to follow instructions supplied with the product.
- Repair or attempted repair by anyone not authorized by us.
- Any damage of the product due to shipment.
- Removal or installation of the product.
- Causes external to the product, such as electric power fl uctuation or failure.
- Use of supplies or parts not meeting our specifi cations.
- Normal wear and tear.
- Any other causes which does not relate to a product defect.
- Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifi cations made to this equipment may void the user’s authority to operate this equipment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Re-position or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Before Installation
- It is very important to mount the equipment in a suitable cabinet or on a stable surface.
- Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
< Part 1 >
Package Contents
|
Model |
Packing Dimension (W x D x H) |
Gross Weight |
|
CV-S101 |
317 x 210 x 107 mm
12.5 x 8.3 x 4.2″ |
1.25 kg
2.8 lb |
Transmitter
| LED | Status | Description |
| POWER | Solid Blue
No Light |
Power is on ( from the local computer or power adapter )
There is no Power |
| ON LINE | Solid Green
Flashing Green No Light |
The connection to Receiver is active
Transmitter is sending or receiving data, or auto-adjusting the signal No connection established |
Transmitter Specification
| Console Port | 1 x DB-15 VGA, up to 1920 x 1440
2 x USB connector for KB & mouse |
| Remote I / O | 1 x RJ-45 port, connect the Receiver up to 1280 x 1024 resolution
( 150 meters ) |
| Local computer | 1 x DB-15 combo KVM port |
| LED | Power ( blue ) & On Line ( green ) |
| Power Input | From attached local computer or optional 12V power adapter |
| Power Consumption | Max. 9W |
| Operating Temperature | 0 to 55°C degree |
| Storage Temperature | -20 to 60°C degree |
| Operating Humidity | 20~90%, non-condensing |
| Storage Humidity | 5 ~90%, non-condensing |
| Operating Altitude | 16,000 ft |
| Non-operating Altitude | 40,000 ft |
| Shock | 10G acceleration ( 11ms duration ) |
| Vibration | 5~500Hz 1G RMS random |
| Dimension ( W x D x H ) | 165 x 85 x 32 mm |
| Weight | 200g |
| Safety | FCC & CE certified |
| Environmental | RoHS2 compliant |
Receiver
| LED | Status | Description |
| REMOTE | Solid Green | Remote port is connected to the Transmitter |
| Solid Red Flashing Red | Remote port is selected
Remote port is selected but no connection established or auto-adjusting the signal |
|
| No Light | Remote port is not connected or the power is OFF | |
| LOCAL | Solid Green | Local port is connected to the local PC / KVM |
| Solid Red
Flashing Red |
Local port is selected
Local port ( PC / KVM ) is selected but no PC signal is detected |
|
| No Light | Local port is not connected or the power is OFF |
| Button | Description |
| SELECT | Switch between REMOTE ( Transmitter ) and LOCAL ( Receiver ) |
Receiver Specification
| Console Port | 1 x DB-15 VGA, up to 1920 x 1440
2 x USB connector for KB & mouse |
| Remote I / O | 1 x RJ-45 port, connect the Transmitter up to 1280 x 1024 resolution
( 150 meters ) |
| Local computer | 1 x DB-15 combo KVM port |
| LED | Local ( green / red ) & Remote ( green / red ) |
| Power Input | 12V power adapter |
| Power Consumption | Max. 9W |
| Operating Temperature | 0 to 55°C degree |
| Storage Temperature | -20 to 60°C degree |
| Operating Humidity | 20~90%, non-condensing |
| Storage Humidity | 5 ~90%, non-condensing |
| Operating Altitude | 16,000 ft |
| Non-operating Altitude | 40,000 ft |
| Shock | 10G acceleration ( 11ms duration ) |
| Vibration | 5~500Hz 1G RMS random |
| Dimension ( W x D x H ) | 165 x 85 x 32 mm |
| Weight | 200g |
| Safety | FCC & CE certified |
| Environmental | RoHS2 compliant |
Application
Extending the KVM console port to 150 meters
Extending the computer to KVM port to 150 meters
Extending the computer up to 150 meters
Keyboard Hotkey Command
You can switch the Receiver from “LOCAL” to “REMOTE” and vice-versa through simple key sequences made by the remote console side. To send commands to the Receiver, you must press the hotkey (default is Scroll Lock) twice within 2 seconds. You will hear a beep sound confi rming you are in the hotkey mode. If you do not press any key during hotkey mode over 2 seconds, the hotkey mode will be terminated and back to normal state.
The default hotkey is Scroll Lock but you can change hotkey as your application convenience.
Example:
The table blow lists all the supported hotkey commands.
| Command | Function |
| C | To switch between Local and Remote ports |
| Q | To turn the beep sound on or off |
| S | To activate the Auto-Scan function. Auto-scan Remote and Local port every 8 seconds repeatedly. |
| A | For auto-adjust video signal of remote port to optimum |
The company reserves the right to modify product specifi cations without prior notice and assumes no responsibility for any error which may appear in this publication.
All brand names, logo and registered trademarks are properties of their respective owners.
Documents / Resources
 |
CyberView CV-S101 Combo KVM Extender [pdf] User Manual CV-S101 Combo KVM Extender, CV-S101, CV-S101 Extender, Combo KVM Extender, KVM Extender, Combo Extender, Extender |
