Cudy GP1200V xPON VoIP Wi-Fi Router Installation Guide

WPS Authorization: Press the WPS button for 1 second to authorize.
Wi-Fi ON/OFF: Press the WLAN button for 2 seconds to turn Wi-Fi on or off. Verify that the Power LED and PON LED are solid on, and the LOS LED is off to ensure successful registration.

Wi-Fi Connection: Connect to the router’s Wi-Fi using the SSID and Password printed on the bottom.
Wired Connection: Turn off Wi-Fi on your device and connect via an Ethernet cable to the LAN port.

FAQ

Q1: Why can’t I access 192.168.1.1?
- Try these solutions: Check the Power status of the PON router, ensure device connectivity to the router, change browser or device, press the RESET button for 5 seconds, or contact ISP for help.

Q2: What if I can’t access the internet after configuration?
- Check LED indicators, ensure ONT has the valid IP address and gateway in WAN settings, configure the router properly in bridge mode, or contact ISP for support.

Buttons and Ports

Caution, laser

DO NOT look directly at the PON port when the device is powered on, as well as the terminal of the indoor fiber cord, to prevent any harm to your eyes.

Connection

Connect your device to the router using A Wi-Fi or B Wired method.

A Wi-Fi: Connect your device to the router’s Wi-Fi using the SSID (network name) and Password printed on the\ bottom of the router.
Go to step 5 and continue

B Wired: Turn off the Wi-Fi on your computer and connect it to the router’s LAN port via an Ethernet cable

Open a browser on a device that is connected to the router and follow the picture to change the Wi-Fi password.

Troubleshooting

Q1: Why I cannot access 192.168.1.1?

Try the following solutions:

Check the Power status of the PON router.
Check if your devices have connected to the router via Wi-Fi or Ethernet cable, and disabled all other

connections such as 4G/5G cellular networks.
Change another web browser or another device and try again.

Press the RESET button for 5 seconds, wait for the LED to turn solid,on and reconfigure from step 1.
Ask your ISP for help.

Q2: What if I cannot access the internet after the configuration?

Try the following solutions:

Check the status of LED indicators.
If you set the ONT to router mode, ensure that the ONT obtains a valid IP address and gateway on the Status > Device > WAN.
If you set the ONT to the bridge mode. Please check if the router you used for dial-up is configured properly.
Contact your ISP for help.

LED

EU Declaration of Conformity

Cudy hereby declares that the device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, directive 2011/65/EU, and Directive (EU) 2015/863. The original EU Declaration of Conformity can be found at http://www.cudy.com/ce.

WEEE
According to the EU Directive on Waste Electrical and Electronic Equipment (WEEE – 2012/19 / EU), this product must not be disposed of as normal household waste Instead, they should be returned to the place of purchase or taken to a public collection point for recyclable waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of the product. For more information, please contact your local authority or the nearest collection point. Improper disposal of this type of waste may result in penalties according to national regulations

GNU General Public License Notice

The software code in this product was created by third parties and is licensed under the GNU General Public License (“GPL”). If applicable, Cudy (“Cudy” in this context refers to the Cudy entity offering respective software for download or being in charge of the distribution of products that contain respective code) makes the corresponding GPL source code available upon request via the ofﬁcial website, either independently or with the assistance of third parties (such as Shenzhen Cudy Technology Co., Ltd.).
For GPL-related questions, email support@cudy.com. In addition, Cudy offers a
GPL-Code-Centre under https://www.cudy.com/gplcodecenterdownload where users can get the GPL source codes used in Cudy products for free. Please note, that the GPL-Code-Centre is only provided as a courtesy to Cudy’s customers but may neither offer a full set of source codes used in all products nor always provide the latest or actual version of such source codes. The GPL code used in this product is subject to the copyrights of one or more authors and is supplied WITHOUT ANY WARRANTY.

CONTACT

www.cudy.com
support@cudy.com
www.cudy.com/download
Support: For technical support, the user guide, and more information, please visit: https://www.cudy.com/support

Documents / Resources

Cudy GP1200V xPON VoIP Wi-Fi Router [pdf] Installation Guide
GP1200V xPON VoIP Wi-Fi Router, GP1200V, xPON VoIP Wi-Fi Router, Wi-Fi Router, Router

References

User Manual

Cudy GP1200V xPON VoIP Wi-Fi Router

Specifications

Product Usage Instructions

FAQ