Wall controller with light
User manual
Thank you for choosing our ventilation controller. Before using the appliance, and to guarantee the best use, read these instructions carefully.
The safety precautions included in this document reduce the risk of death, injury, and electric shock when followed correctly. Please keep the manual in a safe place for future reference, together with the complete warranty card, purchase receipt and package. If
applicable, pass these instructions on to the next owner of the appliance. Always follow basic safety precautions and accident prevention measures when using an electrical appliance. We do not assume any responsibility for non-compliance with these requirements by the customer.
SECURITY INSTRUCTIONS
When using any electrical appliance, the basic safety measures must be respected at all times:
- This appliance is not intended for use by persons with physical, sensory or mental disabilities, or by persons with a lack of experience and knowledge, unless they are supervised or have received instructions regarding its safe use and understand the potential hazards associated with it.
- Before installing the controller, be sure to keep children away to avoid risk, accident or physical damage.
- All wiring must be in accordance with national and local electrical codes and ANI/NFPA 70. If you are not familiar with wiring, consult a qualified electrician.
- If after reading this manual, you do not feel completely sure, we recommend that you contact an electrician or other professional to install this controller correctly.
LOCATION AND INSTALLATION REQUIREMENTS
Warning
- Turn off the power before doing anything with the controller and turn off the power breaker. To avoid possible electrical shock, check that power is off at the fuse box or circuit breaker panel before handling wiring.
ATTENTION! Before beginning assembly, remember to disconnect the light from the panel to avoid electric shock.
PARTS LIST
Carefully open the packaging. Extract the items and verify that all parts are present by checking them against the inventory.
INSTALLATION INSTRUCTIONS
BRACKET FIXING AND CONTROLLER MOUNTING
Use a switch close to the fan to which you are installing the controller.
- Disassemble the switch and terminate the L and N wires separately.
- Hide the wiring well and place the support bracket with the help of the screws that you will find in the package.
- Next, attach the controller which will be attached with the help of the magnets.
- Remove the cover on the back of the controller to insert two AAA batteries and close the cover.
CONTROLLER CONNECTION TO FAN
- To access the controller of your ceiling fan you must remove the two side screws as shown in the image. Once you access the driver, disconnect all wiring and remove the driver from the fan motor.
- Connect the fan motor wires with the driver motor output wires and the Driver light output wires with the LED motor wires by matching the connections in their correct position.
- Connect the N wire from your home to the N wire of the controller and the L wire from your home to the L wire from the driver.
- If your home has a grounding cable, connect all the grounding cables, both from the fan and from the driver and from the support with the one from your home.
- Once the new driver is installed, mount the fan again. Once assembled correctly connect the electricity to pair your new controller.
PAIR THE CONTROLLER
- To pair your controller to the ceiling fan you must press the mute button
on the controller for 5 seconds. - Once paired you will hear a “beep” to confirm that the pairing has been successful.
In compliance with Directives: 2012/19/EU and 2015/863/EU on the restriction of the use of dangerous substances in electric and electronic equipment as well as their waste disposal. The symbol with the crossed dustbin shown on the package indicates that the product at the end of its service life shall be collected as separate waste. Therefore, any products that have reached the end of their useful life must be given to waste disposal centres specialising in separate collection of waste electrical and electronic equipment, or given back to the retailer at the time of purchasing new similar equipment, on a one for one basis. The adequate separate collection for the subsequent start-up of the equipment sent to be recycled, treated and disposed of in an environmentally compatible way contributes to preventing possible negative effects on the environment and health and optimises the recycling and reuse of components making up the apparatus. Abusive disposal of the product by the user involves application of the administrative sanctions according to the laws.
Documents / Resources
 | 24794 Wall Controller with Light |
References
- User Manualmanual.tools
Bonjour,
J’ai voulu connecter le contrôleur mural en suivant les consignes de couplage et pas de bip sonore au bout de 5srcond , ni de couplage.
Merci de votre retour
J’ai voulu connecter le contrôleur mural en suivant les consignes de couplage et pas de bip sonore au bout de 5srcond , ni de couplage.
Merci de votre retour
Why is my CREATE 24794 wall controller not beeping or pairing after holding the button for 5 seconds?
If your wall controller is not beeping or pairing after holding the button for 5 seconds, please check the following steps based on the manual:
AC_LandAC_Nwires from your home must be connected to the driver, and the driver's output wires must be correctly matched to the fan motor and LED wires.Once successfully paired, you should hear a "beep" to confirm the connection.
Read the full Q&A page
Bonjour
La chambre dans laquelle est mise le ventilateur est équipée d’un interrupteur va et vient donc pas de neutre dans l’interrupteur.
Comment dois-je procéder pour apperer le contrôleur
Merci
La chambre dans laquelle est mise le ventilateur est équipée d’un interrupteur va et vient donc pas de neutre dans l’interrupteur.
Comment dois-je procéder pour apperer le contrôleur
Merci
How do I pair the CREATE 24794 wall controller if my switch box lacks a neutral wire?
Based on the manual for the CREATE 24794 Wall Controller, the device itself is battery-powered (requiring two AAA batteries) and does not require a wired power connection to function as a remote. However, the installation of the Driver (receiver) inside the fan unit is what requires both Neutral (N) and Live (L) wires from your home's electrical supply.
If you are replacing a wall switch that lacks a neutral wire, follow these steps to prepare for pairing:
Note: If your wall box lacks a neutral wire, you cannot power a wired device there, but since this controller is battery-operated, you can simply mount the bracket over the existing box after safely terminating the wires.
Read the full Q&A page
Bonjour suite au montage de mon ventilateur je n arrive pas a connecter le controleur mural alors que la telecommande fonctionne bien. J ai le meme probleme sur celui de la chambre d a côté. Pourriez vs m aider?
How do I pair the wall controller with my CREATE ceiling fan?
To pair your wall controller with the ceiling fan, please follow these steps:
If the controller still does not respond, ensure you have inserted two AAA batteries into the back of the unit as described in the installation instructions.
Read the full Q&A page
Same issue there. The wall controller’s mute button doesn’t help pairing.
How do I pair the wall controller with my CREATE ceiling fan?
Same issue there. The wall controller's mute button doesn't help pairing.
Bonjour
Peut-on utiliser la télécommande et la commande murale pour piloter le ventilateur ou faut-il choisir l’un ou l’autre
Merci
Cordialement
Pierre longuet
Peut-on utiliser la télécommande et la commande murale pour piloter le ventilateur ou faut-il choisir l’un ou l’autre
Merci
Cordialement
Pierre longuet
Can I use both the remote control and the wall controller to operate the fan, or must I choose only one?
Yes, you can use both the wall controller and the remote control (command) to operate your fan. The system is designed to work with both interfaces once they are properly paired with the fan's receiver (driver).
According to the manual, the installation process involves replacing the original fan driver with the one provided in the kit. Once the new driver is installed and the power is turned on, you must pair the controller to the fan by following these steps:
The "Parts List" on page 16 confirms that both a "Manette" (Wall Controller) and a "Commande" (Remote Control) are included in the package for use with the same driver.
Read the full Q&A page
J’ai installé deux ventilateurs et la télécommandes murales fonctionne sur les deux ventilateurs
Comment réinitialiser la commande murale svp
Comment réinitialiser la commande murale svp
How do I reset or re-pair the wall controller for my CREATE 24794 fan?
To reset the connection or re-pair your CREATE 24794 wall controller with a specific fan, follow these steps:
If you have two fans and one controller is operating both, you may need to turn off the power to the fan you do not want to pair at the circuit breaker while performing these steps for the first fan. This ensures the signal is only captured by the intended unit.
Read the full Q&A page
Hey, I have accidentally paired my wall controller with my two ceiling fans. How can I unpair one fan from the wall controller?
How do I unpair a ceiling fan from the CREATE 24794 wall controller?
The manual for the CREATE 24794 Wall Controller does not explicitly provide a separate "unpairing" button sequence. However, pairing is typically managed by the receiver (driver) inside the fan canopy when it first receives power.
To resolve your issue and isolate the fans, follow these steps:
If you need to use a different controller for the second fan, repeat this process by powering on only the second fan and pairing it with its own dedicated remote or wall controller. If the fans are on the same electrical circuit and cannot be powered on independently, you may need to temporarily disconnect the wiring (L/N) at the fan motor of the unit you wish to unpair while you perform the pairing sequence for the other unit.
Read the full Q&A page