KINESIS KB100 Split Touchpad Keyboard
Cumpatibilità
The Form keyboard is a multimedia USB keyboard that uses generic drivers provided by the operating system, so no special drivers or software are required. The keyboard is compatible with Windows, macOS, Chrome, Linux, iOS, iPadOS, and many other major operating systems that support USB peripherals.
Nota: Not all operating systems support the use of the integrated touchpad, and a firmware update may be required.
Scelta di USB o Bluetooth
The Form is optimized for wireless Bluetooth Low Energy (“BLE”), but it can be used via USB depending on your preference. To connect the keyboard wirelessly, you will need a Bluetooth-enabled PC, tablesmartphoneone, or SmartTV. To connect the keyboard over USB, you will need a device with an available USB port.
Battery or USB Power
When using the Form in Wireless mode, the keyboard is powered by a 2100 mah Lithium-Ion rechargeable battery. The battery is designed to last for several weeks with the backlighting disabled and full-time use. If the backlighting is on, you will need to charge the keyboard nightly. In sleep mode, it can go months between charges. When the Form is connected to a computer with the included USB-C cable, the keyboard will run off of USB power, and the battery will be charged. The Profile LED (described below) will illuminate Green.
The keyboard will automatically go to sleep after 30 seconds of inactivity to conserve power. Tap any key to instantly wake the keyboard and pick up where you left off. You can use the slide switch on the left side of the back edge.
Nota: The keyboard ships from the factory with only a partially charged battery. We recommend plugging the keyboard in on he first night you receive it to fully charge it. A full charge should take around 6-8 hours.
Bluetooth Mode: Initial Pairing
The Form can be paired with 2 different Bluetooth-enabled devices. The toggle switch on the right side of the back edge is used to switch between the two color-coded Bluetooth Profiles: The left position corresponds to Profile 1 (White LED), and the right position corresponds to Profile 2 (Blue LED).
- With the keyboard disconnected from all USB ports, slide the toggle switch on the left side of the back edge to the right to turn on the battery power.
- U Profile LED should flash rapidly in either White or Blue to reflect Profile 1 o 2.
- Navigate to your PC’s Bluetooth menu.
- Locate and select the “FORM” device from the menu and follow the prompts to connect.
- U Profile LED will go “solid” when the keyboard pairs successfully for that Profile.
- If you would like to pair an additional device, use the toggle switch on the right side of the back edge to change Profiles and repeat steps 2-3 above.
Modu USB
- Simply use the included cable to connect the keyboard
- The left LED is the conventional Caps Lock indicator. It illuminates white when Caps Lock is activated on the paired or connected computer (if supported)
- The right LED is the Profile LED. It illuminates White in Profile 1, Blue in Profile 2, and Green when in USB Mode.
- Se u Profile LED is flashing FAST, it means the keyboard is ready and available to be paired over.
- Bluetooth for that Profile (White or Blue)
- Se u Profile LED is flashing SLOW, it means the keyboard is unable to locate the device that was previously paired for that Profile (White or Blue)
- Se u Profile LED is SOLID, it means the keyboard is successfully paired and connected to a PC over Bluetooth for that Profile (White or Blue). Note: To conserve battery, the Profile LED will turn off after 3 seconds.
DICHIARAZIONE DI CONFORMITÀ FCC
Stu dispusitivu hè conforme à a parte 15 di e regule FCC.
U funziunamentu hè sottumessu à i seguenti dui cundizioni:
- Stu dispusitivu ùn pò causari interferenza dannusu, è
- (Stu dispusitivu deve accettà ogni interferenza ricevuta, cumpresa l'interferenza chì pò causà operazione indesiderata.
Nota: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and usedbyh the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Suppose this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. In that case, the user is encouraged to try to correct the interference by one or more of the following measures:
- Riorientate o rilocate l'antenna di ricezione.
- Aumente a separazione trà l'equipaggiu è u ricevitore.
- Cunnette l'equipaggiu à una presa in un circuitu diversu da quellu à quale hè cunnessu u ricevitore.
- Cunsultate u rivenditore o un tecnicu espertu di radio/TV per aiutu.
Attenzione: Cambiamenti o mudificazioni à sta unità chì ùn sò micca appruvati espressamente da a parte rispunsevuli di a conformità puderanu annullà l'autorità di l'utilizatore per operà l'equipaggiu.
Dichjarazione di l'esposizione à a radiazione FCC
U dispusitivu hè statu valutatu per risponde à i requisiti generali di esposizione RF.
U dispusitivu pò esse usatu in cundizioni di esposizione portable senza restrizioni.
Documenti / Risorse
 |
KINESIS KB100 Split Touchpad Keyboard [pdfManuale d'usu KB100, 2BEGH-KB100, 2BEGHKB100, KB100 Split Touchpad Keyboard, KB100, Split Touchpad Keyboard, Touchpad Keyboard, Keyboard |