USER MANUAL
CLOCKY’S BUTTONS
IMPORTANT
WARNING!
- Clocky is not a toy. Children should be supervised when he is in use.
- Clocky should sit on a nightstand no higher than 3 feet.
- Place barriers so that Clocky does not fall down stairs or balconies.
- Clocky should not be thrown. Let him roll off the table by himself.
- Clocky’s wheels can be stopped any time by pressing the alarm bell button.
- Clocky should not be placed in such a way that he can knock down liquids.
QUICKSTART
Install batteries Turn Clocky around and unscrew the battery door using a small screwdriver. Insert 4 lithium AM batteries. Follow the labels printed inside the battery compartment to install the batteries in the right direction.
Select 12 or 24 hour mode To switch between 12 and 24 hour mode, press and hold the ‘t’ button for 3 seconds. To distinguish between AM and PM in 12 hour mode, note the presence or absence of the PM sign.
Set Time Press the ‘t’ button once. The current time screen will start flashing. Use the ‘h’ and ‘m’ buttons to advance hours and minutes to the current time. To advance hours and mintues faster, press and hold the ‘h’ or ‘m’ buttons. To leave set time mode, press the ‘t’ button again or wait until the screen stops flashing.
Set Alarm Time Press the ‘a’ button once. T he alarm time screen will start flashing. Use the ‘h’ and ‘m’ buttons to advance hours and minutes until the desired alarm time is reached. To advance hours and minutes faster, press and hold the ‘h’ or ‘m’ buttons. To leave set alarm mode, press the ‘a’ button again or wait until the screen stops flashing.
Set Snooze Time Press the ‘a’ button twice rapidly. When your snooze is 0, Clocky will move as soon as it’s alarm time, but if it is enabled (1-9) then you must hit the snooze button before it rolls away. Press the m button to change this. If 1 is chosen you can snooze for one minute. If 2 is chosen, you can snooze for two minutes, and so on up to 9 minutes. To leave this mode, press the ‘a’ button again or just wait until the screen stops flashing.
Turn Alarm On/Off Press the alarm on/off button. A corresponding icon will show up on the screen to indicate that the alarm state is on/off. You will also use this button to stop the alarm and wheels after Clocky’s alarm sounds.
Turn Wheels On/Off Press the wheels button to turn the wheels on/off. A corresponding icon will show up on the screen when the wheels are on/off.
Read the full manual here:
https://clocky.com/pages/manual
Need extra help?
Check: https://clocky.com/pages/faq-support
WARRANTY:
https://clocky.com/pages/support
MANUAL:
https://clocky.com/pages/manual
HELP?
team@clocky.com
FOLLOW US:
@clockythealarm
PATENT 7355928
2018 Clocky, LLC. Previously Nanda Home, Inc. All Rights Reserved. This product is produced from original artwork. All copyright and trademark rights in the distinctive appearance and function of this article are owned by Clocky, LLC. Clocky® is a trademark of Clocky, LLC. Distributed by Clocky, LLC. 340 S Lemon Ave #7919, Walnut, CA 91789 USA Designed in the USA. Printed in China.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver,
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read More About This User Manuals…
Questions about your Manual? Post in the comments!
References
- User Manualmanual.tools
My clocky will not let me change either the hours or the mins. It did work before. Only used couple of months then wouldn’t reset. I even put new batteries in. So I just tried it again after I put new batteries in again cause I quit using it. The alarm does go off on it’s own, but I cant set the time at all
What do I do? Thanks Joannie mccrite
What do I do? Thanks Joannie mccrite
How do I fix my Clocky if the hours and minutes buttons are not responding when trying to set the time?
If your Clocky is not allowing you to change the hours or minutes, please try the following troubleshooting steps based on the official manual and support guidelines:
If the buttons remain unresponsive after these steps, the manufacturer suggests contacting them at team@clocky.com with details about the problem for further warranty or repair assistance.
Read the full Q&A page
I can’t get the display screen with the time to be lit up all the time so I can see it. I have the time set. Everything seems to be working, but I really need to see the screen and can’t see anything at all unless I press the time button and it lights for 3 seconds and then goes dark again. Help!
How can I keep the Clocky display screen lit up all the time?
Based on the Clocky instruction manual and official support documentation, the display screen is designed to be backlit only temporarily when a button is pressed. There is no setting to keep the backlight permanently illuminated.
The backlight typically stays on for a few seconds (such as when you press the 't' button to check the time) to conserve battery life, as the device runs on 4 AAA lithium batteries. If you are having difficulty seeing the screen at all without the backlight, ensure that:
If the screen is completely blank (no digits visible) unless the light is on, this may indicate low battery power or a technical fault. However, the 3-second auto-off behavior for the light itself is the standard operation for this product.
Read the full Q&A page
This is the person who purchased from Amazon this time.
I bought it for a gift, but the person who received it told me that the lid for inserting the battery would not open.
I’m in trouble because the screws seem to run out of threads.
I was exchanging messages on Amazon.
please confirm.
Since it is a gift, please respond promptly.
今回Amazonから購入させていただいた者です。
プレゼント用に購入したのですがもらった人が電池を入れる蓋が、開かないという連絡がありました。
ネジもネジ山がなくなりそうな感じで困っています。
Amazonでメッセージのやり取りをしていました。
ご確認ください。
プレゼントなので敏速な対応お願いします。
I bought it for a gift, but the person who received it told me that the lid for inserting the battery would not open.
I'm in trouble because the screws seem to run out of threads.
I was exchanging messages on Amazon.
please confirm.
Since it is a gift, please respond promptly.<e/em>
今回Amazonから購入させていただいた者です。
プレゼント用に購入したのですがもらった人が電池を入れる蓋が、開かないという連絡がありました。
ネジもネジ山がなくなりそうな感じで困っています。
Amazonでメッセージのやり取りをしていました。
ご確認ください。
プレゼントなので敏速な対応お願いします。
How can I open the battery compartment if the screws are stripped or stuck?
We are sorry to hear that you are experiencing difficulty with the battery compartment screws on your Clocky. Because Manuals+ is a repository for instruction manuals and is not the manufacturer or the seller (Amazon), we cannot directly process exchanges or refunds.
Based on the official Clocky support documentation, here are the recommended steps for this situation:
Please refer to the Clocky Warranty page for more information on their replacement policy for defective units.
Read the full Q&A page
does let me change to 12 hrs or am
How do I change Clocky to 12-hour mode or see the AM/PM indicator?
To change the time format on your Clocky, follow these steps:
Note: If you are currently in 12-hour mode during an AM hour, you may not see an immediate visual change when switching to 24-hour mode until the time reaches 13:00 (1:00 PM).
Read the full Q&A page
sorry does not let me
our clock came with NO manual or instructions..
Where can I find the instruction manual for Clocky?
If your Clocky did not come with a physical manual, you can follow these quickstart steps to get it set up:
You can download the full PDF manual directly from the official site at clocky.com/pages/manual.
Read the full Q&A page
Something’s happened to my clocky alarm clock, I can’t set time or alarm. Press ‘T’ and the alarm is going off have to press snooze to stop it. Press ‘A’ and can’t set the alarm either.
How do I troubleshoot my Clocky when the buttons are not allowing me to set the time or alarm and the alarm triggers unexpectedly?
It sounds like your Clocky may be experiencing a power or internal logic error. Please try the following steps to reset and troubleshoot the device:
If the 'T' button continues to trigger the alarm instead of flashing the time display after a battery reset, the internal switch may be damaged, and you should contact team@clocky.com for warranty support.
Read the full Q&A page