8200 Series Catalyst Network Interface Module
“
Product Information
Specifications:
- Product: Cisco Catalyst Network Interface Module
- Compatibility: Cisco Catalyst 8200 Series Edge Platforms
Product Usage Instructions
Installing the Cisco Catalyst Network Interface Module:
- Locate the NIM slot on the front panel.
- Loosen the screws to remove the NIM blank cover.
- Insert the NIM into the slot.
- Tighten the screws to secure the NIM in the slot.
Removing the Cisco Catalyst Network Interface Module:
- If the NIM is operational, issue the command ‘hw-module subslot
slot 0/2 stop’ to shut it down gracefully. - Locate the NIM slot on the front panel.
- Loosen the screws that secure the NIM.
- Gently pull out the NIM from the slot.
Caution: Always shut down the NIM gracefully
before removal to prevent damage to the card.
Note: Ensure all module slots have a module or blank
installed for thermal and safety reasons.
For additional information:
Refer to the Cisco Catalyst 8200 Series Edge Platforms datasheet
on cisco.com for a list of supported NIMs on the platforms.
FAQ
Q: Why is it important to shut down the NIM gracefully before
removal?
A: Shutting down the NIM gracefully prevents
damage to the card and ensures smooth removal without any
operational issues.
“`
Install Cisco Catalyst Network Interface Module
This section provides information before and during the installation of Cisco Catalyst Network Interface Modules (NIMs) on the Cisco Catalyst 8200 Series Edge Platforms.
· Overview of the Network Interface Module, on page 1 · Remove and Install Network Interface Modules, on page 2
Overview of the Network Interface Module
The Cisco Catalyst Network Interface Module (NIM) is supported on Cisco Catalyst 8200 Series Edge Platforms. These are the steps to install a NIM: 1. Locate the NIM slot on the front panel. 2. Loosen the screws to remove NIM blank cover. 3. Insert the NIM into the slot. 4. Tighten the screws to secure the NIM in the slot. These are the steps to remove a NIM: 1. If the NIM is up and running, issue the following command to shut down the NIM gracefully before
removing it: hw-module subslot slot 0/2 stop
Caution If you do not shut down the NIM gracefully before removing it, the NIM card could get damaged.
2. Locate the NIM slot on the front panel. 3. Loosen the screws that secure the NIM. 4. Gently pull out the NIM from the slot. All module slots must have a module or blank installed for the product to work thermally and for safety purposes.
Install Cisco Catalyst Network Interface Module 1
Remove and Install Network Interface Modules
Install Cisco Catalyst Network Interface Module
For additional information, see the Cisco Catalyst 8200 Series Edge Platforms datasheet on cisco.com for a list of supported NIMs on the platforms.
Remove and Install Network Interface Modules
Keep the following tools and equipment while working with the Network Interface Modules (NIM)s: · Number 1 Phillips screwdriver or a small flat-blade screwdriver · ESD-preventive wrist strap
Remove the Network Interface Module
Step 1 Shut down the electrical power to the slot in the device, turn off the electrical power to the device. Leave the power cable plugged-in to channel ESD voltages to ground. Step 2 Remove all network cables from the rear panel of the device. Using a number 1 Phillips screwdriver, loosen the captive screws on the network interface module. Step 3 Slide the network interface module out. Step 4 If you are not replacing the module, install a blank faceplate over the empty slot to ensure proper air flow.
Install the Cisco Catalyst Network Interface Modules
Step 1 Shut down the electrical power to the slot in the router by turning off the electrical power to the router. Leave the power cable plugged in to channel ESD voltages to ground. Step 2 Remove all network cables from the rear panel of the device. Step 3 Remove the blank faceplates installed over the network interface module slot that you intend to use.
Note Save blank faceplates for future use.
Step 4 Align the module with the guides in the chassis walls or slot divider and slide it gently into the NIM slot on the device. Step 5 Push the module into place until you feel the edge connector seat securely into the connector on the router backplane. The module faceplate should contact the chassis rear panel. Step 6 Using a number 1 Phillips screwdriver, tighten the captive screws on the network interface module. Step 7 Connect the module to the network and re-enable the power to the slot in the device.
Install Cisco Catalyst Network Interface Module 2
Documents / Resources
 |
CISCO 8200 Series Catalyst Network Interface Module [pdf] User Guide 8200 Series, 8200 Series Catalyst Network Interface Module, Catalyst Network Interface Module, Network Interface Module, Interface Module |