CipherLab RS35 UHF RFID Reader User Guide

CipherLab RS35 UHF RFID Reader

RS35 UHF RFID Reader, a pistol-shaped handle with a trigger button, is used for working with the RS35 Mobile Computer to read UHF RFID tags.

Open Your Box

• RS35 UHF RFID Reader/
• Battery/ I b’T 1)
• Battery Charger Quick Start Guide
• RS35 UHF RFID Reader Quick Start Guide

Overview

LED Indicator

The LED Indicator on the UHF RFID Reader gives the following status indications.

Install & Remove

To mount the RS35 mobile computer onto the RS35 UHF RFID Reader

• Step 1:
  Loosen the 2 screws on the back side of the RS35 mobile computer to remove the hand strap hole cover, which covers the contact pins. If a hand strap is attached, removed it from the RS35 mobile computer as well.
• Step 2:
  With the back side of the RS35 mobile computer downwards, insert its top side into the top shell of the UHF RFID Reader first, and then press down the bottom side of the RS35 mobile computer to fasten it till you hear a “click” sound.

To remove

• Step 1:
  As the figure shows, place the RS35 mobile computer installed with a UHF RFID Reader on a horizontal flat surface by both your hands holding both two sides of the top shell.
• Step 2:
  Keep holding the top shell with both hands, and slightly pull the top shell sides of the UHF RFID Reader with your thumbs.

• Step 3:
  While the top shell sides are pulled aside by your thumbs, use other fingers to push out the RS35 mobile computer from its back side to separate it apart with the UHF RFID Reader.

Scanning

• Step 1: Launch the application “EZ Config” on your RS35 mobile computer.
• Step 2: Aim the RFID Antenna at the UHF RFID tag to read.
• Step 3: Pull the trigger on the handle.

Install & Remove Battery

To install the battery:

• Step 1: Pull up the captive screw and twist it anticlockwise to open the lid.
• Step 2: Put the battery into the battery chamber from the contact pins end.
• Step 3: Close the lid and twist the captive screw clockwise to lock it.

To remove the battery, simply twist the captive screw anticlockwise and take the battery out.

Charging

• By charging the RS35 mobile computer mounted on the UHF RFID Reader, the UHF RFID Reader can be charged at the same time.
• The charging time is approximately 6 hours.
• The UHF RFID Reader stops working during the charging period.

Warning: For charging the UHF RFID Reader through the mounted mobile computer, be sure to connect to the AC adapter, but not PC.

 FCC STATEMENT

CAUTION:
USA (FCC):
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

RF Exposure warning

• This device meets the government’s requirements for exposure to radio waves.
• This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications  Commission of the U.S. Government.

The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC, with the EUT transmitting at the specified power level in different channels. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm after searching on FCC ID: Q3N-RUHFII.

www.cipherlab.com

FAQ

• Q: What should I do if I experience interference while using the device?
• A: If you experience interference, try moving the device to a different location or adjusting its positioning. Ensure no other electronic devices are causing interference.
• Q: How can I check the SAR information for this device?
• A: You can find SAR information on the FCC website by searching the FCC ID: Q3N-RUHFII under the Display Grant section.