Operation Manual
WIRING & FUNCTIONS (S1)
Proper installation of the product requires the installer to have a good understanding of automotive electronics, systems and procedures. Different applications may require different functions. For optimum efficiency, it is highly recommended to determine, configure and test the required functions prior to Installation.
WIRING:
- Route power cable’s red wire to a fused Install a fuse (user-supplied) on the end of power cable’s RED wire and route that wire to vehicle battery. Connect the BLACK wire to the vehicle chassis ground.
NOTE: Follow factory wiring harness through the firewall. It may be necessary to drill a hole in the firewall. Ensure that there is no component that could be damaged from the drilling. - Route control wires towards the dash area to a switch panel (user-supplied). Connect the required wires to the switch panel.
NOTE: Make sure that all wires of power cable are securely connected to power source.
WARNING
- DO NOT USE THE POWER WIRE(S) AS THE LIGHTBAR ACTIVATION SWITCH. USE ONLY THE FUNCTION WIRE(S) TO SWITCH AND ACTIVATE.
- FAULTY CONNECTIONS MAY CAUSE THE LIGHTBAR TO MALFUNCTION AND / OR RESET TO ITS DEFAULT SETTINGS.
- DO NOT USE A HIGH PRESSURE POWER WASHER TO CLEAN YOUR LIGHTBAR; THIS MAY DAMAGE YOUR LIGHTBAR AND VOID ITS WARRANTY.
FUNCTIONS:
WARNING MODE
Activate Warning Mode by applying +VDC to BROWN wire for warning mode.
NOTE: Default flash pattern FP#1
YELLOW WIRE (Flash Pattern Change / DIM MODE)
There are 3 type of functions for YELLOW wire,
- Flash Pattern Change only. [DEFAULT function]
To change flash pattern , tap +VDC to YELLOW wire while in a warning mode,
■ Quick once to the next pattern.
■ Quick 3 times to reset to default flash pattern. - DIM MODE only.
Activate Low Power function by apply +VDC to YELLOW wire while in a warning mode.
NOTE: flash pattern change function is disabled. - Flash Pattern Change & DIM MODE.
To change flash pattern , tap +VDC to YELLOW wire (<1 second) while in a warning mode,
■ Quick once to the next pattern.
■ Quick 3 times to reset to default flash pattern.
Activate Low Power function by apply +VDC to YELLOW wire (>1 second) while in a warning mode.
Programming YELLOW wire function,
a. Activate warning mode by applying +VDC to BROWN wire.
b. Quick 3 times to tap +VDC to GREEN wire, the lightbar will enter into programming mode.
c. The Front Side of lightheads will show the function by flashing:
■ Single Flash : Flash Pattern Change only. [DEFAULT]
■ Double Flash : DIM MODE only.
■ Triple Flash : Flash Pattern Change & DIM MODE.
d. Tap +VDC to YELLOW wire will change to next function.
e. Save and leave programming mode by disconnecting power.
| FLASH PATTERN | ||
| 1 | Double [2Hz] | All |
| 2 | Quad [2Hz] | All |
| 3 | Single [2Hz] | All |
| 4 | Double (Corners) [2Hz] | All |
| 5 | Quad (Corners) [2Hz] | All |
| 6 | Single (Corners) [2Hz] | All |
| 7 | Random | All |
| 8 | Single | All |
| 9 | Double | All |
| 10 | Quad | All |
| 11 | Quint | All |
| 12 | Mega | All |
| 13 | Ultra | All |
| 14 | Cruise (Corners) | All |
| 15 | Cruise | All |
| 16 | Single-Quad | All |
| 17 | Single H/L | All |
| 18 | Side-by-Side Single | NA |
| 19 | Side-by-Side Ultra | NA |
| 20 | Rotator1(fast) | NA |
| 21 | Rotator2(slow) | NA |
| 22 | Double [2Hz] | Split |
| 23 | Quad [2Hz] | Split |
| 24 | Single [2Hz] | Split |
| 25 | Double (Corners) [2Hz] | Split |
| 26 | Quad (Corners) [2Hz] | Split |
| 27 | Single (Corners) [2Hz] | Split |
| 28 | Random | Split |
| 29 | Single | Split |
| 30 | Double | Split |
| 31 | Quad | Split |
| 32 | Quint | Split |
| 33 | Mega | Split |
| 34 | Ultra | Split |
| 35 | Single-Quad | Split |
| 36 | Single H/L | Split |
ILLUMINATED CENTER SECTION
Activate Illuminated Center Section (ICS Lights) by applying +VDC to ORANGE wire.
FRONT AND REAR TAKE DOWN/WORK LIGHT
Activate Front and Rear Take Down/Work Light by applying +VDC to GREEN wire.
BRAKE (STOP) / TAIL / TURN INDICATOR LIGHTHEAD
Activate rear facing Break (stop) / Tail / Turn Indicator Lighthead by applying +VDC to
- WHITE wire for Brake (Stop) Lightheads.
- GRAY wire for Tail Lightheads.
- PURPLE wire for Left Turn Signal Lighthead.
- BLUE wire for Right Turn Signal Lighthead.
CAUTION: The Brake (stop) / Tail / Turn Indicator Lighthead(s) in the lightbar can only be used as an auxiliary Brake (stop) / Tail / Turn Indicator lamp(s) and must not used to replace the original Brake (stop) / Tail / Turn Indicator lamp(s) of the vehicle.
v.1.0
Rev.220808
Documents / Resources
 |
cell2 Kuiper HE Illuminated Centre 1369.6mm [pdf] Instruction Manual Kuiper HE Illuminated Centre 1369.6mm, HE Illuminated Centre 1369.6mm, Illuminated Centre 1369.6mm, Centre 1369.6mm, 1369.6mm |
