Instruction Manual for cell2 models including: Kuiper HE Illuminated Centre 1369.6mm, HE Illuminated Centre 1369.6mm, Illuminated Centre 1369.6mm, Centre 1369.6mm, 1369.6mm
Kuiper HE Illuminated Centre 1369.6mm (53.9") - BB (12~24VDC) - Cell2
Kuiper HE Illuminated Centre 1517mm (59.5") - RC - Cell2
Operation Manual LKPR WIRING & FUNCTIONS (S1) Proper installation of the product requires the installer to have a good understanding of automotive electronics, systems and procedures. Different applications may require different functions. For optimum efficiency, it is highly recommended to determine, configure and test the required functions prior to Installation. LIGHTBAR WIRING STT STT RED BLACK to +VDC with rated fuse (for correct rating, refer to the Lightbar Specification) to Chassis Ground BROWN ORANGE WHITE GRAY PURPLE BLUE YELLOW GREEN Warning Mode Illuminated Center Section Brake (Stop) Light Tail Light Left Turn Light Right Turn Light Flash Pattern Change Front and Rear Take Down/Work Light WIRING: 1. Route power cable's red wire to a fused Install a fuse (user-supplied) on the end of power cable's RED wire and route that wire to vehicle battery. Connect the BLACK wire to the vehicle chassis ground. NOTE: Follow factory wiring harness through the firewall. It may be necessary to drill a hole in the firewall. Ensure that there is no component that could be damaged from the drilling. 2. Route control wires towards the dash area to a switch panel (user-supplied). Connect the required wires to the switch panel. NOTE: Make sure that all wires of power cable are securely connected to power source. WARNING DO NOT USE THE POWER WIRE(S) AS THE LIGHTBAR ACTIVATION SWITCH. USE ONLY THE FUNCTION WIRE(S) TO SWITCH AND ACTIVATE. FAULTY CONNECTIONS MAY CAUSE THE LIGHTBAR TO MALFUNCTION AND / OR RESET TO ITS DEFAULT SETTINGS. DO NOT USE A HIGH PRESSURE POWER WASHER TO CLEAN YOUR LIGHTBAR; THIS MAY DAMAGE YOUR LIGHTBAR AND VOID ITS WARRANTY. v.1.0 - 4 - Rev.220808 - 1 - v.1.0 FUNCTIONS: WARNING MODE Activate Warning Mode by applying +VDC to BROWN wire for warning mode. NOTE: Default flash pattern FP#1 FLASH PATTERN 1 Double [2Hz] All 2 Quad [2Hz] All 3 Single [2Hz] All 4 Double (Corners) [2Hz] All YELLOW WIRE (Flash Pattern Change / DIM MODE) 5 Quad (Corners) [2Hz] All There are 3 type of functions for YELLOW wire, 6 Single (Corners) [2Hz] All 7 Random All 1. Flash Pattern Change only. [DEFAULT function] To change flash pattern , tap +VDC to YELLOW wire while in a warning mode, 8 Single 9 Double All All Quick once to the next pattern. 10 Quad All Quick 3 times to reset to default flash pattern. 11 Quint All 12 Mega All 2. DIM MODE only. 13 Ultra All Activate Low Power function by apply +VDC to YELLOW wire while in a warning mode. 14 Cruise (Corners) All 15 Cruise All NOTE: flash pattern change function is disabled. 16 Single-Quad All 3. Flash Pattern Change & DIM MODE. 17 Single H/L All To change flash pattern , tap +VDC to YELLOW wire (<1 second) while in a warning mode, 18 Side-by-Side Single NA 19 Side-by-Side Ultra NA Quick once to the next pattern. 20 Rotator1(fast) NA Quick 3 times to reset to default flash pattern. 21 Rotator2(slow) NA Activate Low Power function by apply +VDC to YELLOW 22 Double [2Hz] Split wire (>1 second) while in a warning mode. 23 Quad [2Hz] Split Programming YELLOW wire function, 24 Single [2Hz] Split a. Activate warning mode by applying +VDC to BROWN wire. 25 Double (Corners) [2Hz] Split 26 Quad (Corners) [2Hz] Split b. Quick 3 times to tap +VDC to GREEN wire, the lightbar will enter into programming mode. 27 Single (Corners) [2Hz] Split 28 Random Split c. The Front Side of lightheads will show the function by 29 Single Split flashing: Single Flash : Flash Pattern Change only. [DEFAULT] Double Flash : DIM MODE only. Triple Flash : Flash Pattern Change & DIM MODE. 30 Double 31 Quad 32 Quint 33 Mega Split Split Split Split d. Tap +VDC to YELLOW wire will change to next function. 34 Ultra Split e. Save and leave programming mode by disconnecting 35 Single-Quad Split power. 36 Single H/L Split ILLUMINATED CENTER SECTION Activate Illuminated Center Section (ICS Lights) by applying +VDC to ORANGE wire. FRONT AND REAR TAKE DOWN/WORK LIGHT Activate Front and Rear Take Down/Work Light by applying +VDC to GREEN wire. BRAKE (STOP) / TAIL / TURN INDICATOR LIGHTHEAD Activate rear facing Break (stop) / Tail / Turn Indicator Lighthead by applying +VDC to WHITE wire for Brake (Stop) Lightheads. GRAY wire for Tail Lightheads. PURPLE wire for Left Turn Signal Lighthead. BLUE wire for Right Turn Signal Lighthead. CAUTION: The Brake (stop) / Tail / Turn Indicator Lighthead(s) in the lightbar can only be used as an auxiliary Brake (stop) / Tail / Turn Indicator lamp(s) and must not used to replace the original Brake (stop) / Tail / Turn Indicator lamp(s) of the vehicle. v.1.0 - 2 - - 3 - v.1.0Adobe PDF library 15.00