2 in 1 Infrared Thermometer Ear and Object KI-8171L Instruction Manual

Infrared Thermometer Ear and Object KI-8171L

Instruction Manual

2 in 1 Infrared Thermometer

2 in 1 Infrared Thermometer Ear and Object
Model : KI-8171L

Precautions

  1. Please consult your physician to verify your body temperature.
  2. DO NOT scrape or scratch the lens as it will hamper the effectiveness of the device.
  3. The device is intended for consumer use only.
  4. Do not drop or expose thermometer to electric shock as this may adversely affect its performance.

POWER SOURCE SIZE AAA(1.5V)x 2
WARRANTY: ONE YEAR FROM THE DATE OF PURCHASE

Parts Identification

Parts Identification

About IR and Body Temperature
Why an IR ear thermometer?
The tympanic membrane (eardrum), and the hypothalamus, the part of the brain which controls body temperature, share a common blood supply so tympanic readings rise and fall rapidly with core temperature (deep body temperature). This makes the ear temperatures one of the best indicators of internal body (core) temperature.

What are normal temperature values?
Human body temperature varies from person to person, some run in the lower range (96-97°F) and some run in the higher range (98-99°F). Also, your normal body temperature changes throughout the day and can vary at different times of the year. It is very important to know your normal body temperature range. We recommend measuring yourself when healthy to establish reference temperatures. This will help you feel more confident of the measured temperature readings when ill.

Information You Should Know Before Operating the IR Ear Thermometer
How to correctly use the IR ear thermometer

  1. It is useful to try this thermometer on yourself first to become familiar with it’s operations.
  2. Do not take the temperature immediately upon waking. Sleeping on the ear can cause the temperature to be higher than normal.
  3. It is common for the readings to be slightly different between the right and left ear. We suggest using the same ear to obtain temperature readings.
  4. Straighten the ear canal for measuring: Children under 12 months: Straighten ear canal by gently pulling the ear back.
Ear Back

Children over 12 months and Adults: Straighten the ear canal by gently pulling the ear back and up.

Ear Back and Up

6. Make sure the ear canal is dry, clean and free of was or particulates.

Preparation for Use
Installing/Replacing the Battery:

  1. Slide the battery cover off in the direction shown below.
  2. If replacing, carefully remove batteries.
  3. Clean the battery ends as well as the contacts in the device prior to reinstalling batteries.
  4. Install two new AAA batteries into the battery compartment making sure to match the correct polarities (+ and -).
  5. Replace and securely fasten the battery cover as shown below.
Replacing the Battery

WARNING:
Batteries Contain Mercury. DO NOT PUT IN REGULAR TRASH, dispose of in recycling trash only. Recycle or manage as hazardous waste. Never dispose of batteries in fire. Do not recharge (unless rechargeable), put in backwards or disassemble. This may cause explosion, leakage and injury.

CAUTION:
When replacing batteries, do not mix old ones and new ones. Never mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.

How to Operate the Thermometer
NOTE: Each time you turn on the unit, it will automatically run a diagnostic check and the screen will show colors and all symbols:

symbols

QUICK START

  1. Press and release the POWER button. You will hear a short beep and the memory will show the last temperature taken.
  2. Place the Probe inside the ear canal or aim toward the object approximately – 1 ‘/x inches (1- 3 cm) from surface.
  3. Press and release the POWER button to record new measurement.
  4. Two short beeps let you know the measurement is complete/ready to read.
  5. The temperature and back light color shows on the display. The back light color will light according to the reading:
Color Table

6. Turn the unit off by pressing and holding the POWER button for about 5 seconds until the display shows OFF and a long beep is heard.

OFF

7. The device will automatically shut off after about 1 minute of non-use.

SETTING THE SCALE °C or °F

  1. Press and release the POWER button to turn on the device.
  2. Immediately press it again and hold down until you see the °C or °F change. Release the button as soon as change occurs.
SETTING THE SCALE

3. The device is now ready to take a measurement.

CHANGING MODES
This device has two modes: (1)Ear (2)Object

  1. Ear mode is for measuring temperature of the tympanic membrane (eardrum) to determine body temperature.
  2. Object mode is for measuring temperature of an object or surface. This mode is not intended for measuring human body temperature.

*Device will always power on in Ear Mode*

  1. Press and release the POWER button to turn on the device.
  2. Immediately press and hold the Memory/Mode button until you see either
Memory

then release button.

3. You may toggle between modes simply by following step 2.

RECALL MEMORIES
This device will hold 10 temperature readings in memory (Ear and Object readings combined).
• Ear memories will show the small .111 ear icon in the top right side of display.
• Object memories show nothing in that area.

  1. The device must be powered OFF in order to recall memories.
  2. Simply press and release the Memory/Mode button to show stored temperature readings.
  3. The most recent temperature reading will be the first to show.
  4. When viewing memory, the device will automatically shut off after 3 seconds of non-use.

DELETE MEMORIES

  1. Repeat steps land 2 in “Recall Memories”
  2. Press and hold the Power button until “dEL” is displayed.
  3. Release button. All stored memories are now deleted Device will automatically shut off.
DELETE MEMORIES

IMPORTANT THINGS TO KNOW

  • Allow at least 1-3 minutes between each measurement in order to obtain the most accurate result.
  • The default mode is Ear mode. Any time the unit is powered off, it will power on in ear mode.
  • Make sure the probe lens is clean and clear before use. It should be ‘mirror like’ or reflective. A dirty, blocked or scratched lens will cause incorrect results.
  • Do not store the device in extreme conditions or temperatures (ie., direct sunlight, very hot/cold or high moisture like a bathroom). Unit is not waterproof.
  • If it has been stored in extreme conditions, wait at least one hour for it to return to a normal room temperature before using.
  • Wait at least thirty minutes after bathing, exercising or eating before taking a measurement. . Do not dismantle or modify the device other than changing the batteries.
  • This device has no user serviceable parts. Do not dismantle or modify other than changing the batteries.

CLEANING AND CARE

CLEANING AND CARE

ERROR MASSAGE

ERROR  MASSAGE

SPECIFICATIONS

SPECIFICATIONS

LIMITED WARRANTY
This device (batteries excluded) is guaranteed for one year from the data of purchase against manufacturer’s defect under normal use and without evidence of tampering.

WARRANTY EXCLUSIONS:
• Device is not properly operated according to the instructions as described in this manual.
• Device shows any signs of tampering or attempted modification.
• Evidence of improper handling or storing, such as dropping, heat, liquid or cleaner damage.
• Natural disasters (such as fire, flood, earthquake, lightening).
• Na receipt or proof of purchase showing dote of purchase

Following the instructions closely will ensure years of dependable operation.

FCC STATEMENT

POTENTIAL FOR RADIOS/TELEVISION INTERFERENCE (For USA Only)
Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protector against harmful interference in a residential The product generates, LISPS, and ran radiate radio frequency energy and, T not installed and used in accordance with the Instructions, may cause harmful Interference to tad e communicator, However, there is no guarantee that Interference will not occur In a particular installation, If the product does cause harmful Interference to radio or television receptor, which can be determined by turnings the product on and oft the user is encouraged to try to correct the interference by one or more of the following measure:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Consult the dealer or an experienced radio / TV technician for help.

Questions about your Manual ? Post in the comments!

Electronic Nasal Aspirator NS14 Instruction Manual

Electronic Nasal Aspirator NS14

Instruction Manual

Electronic Nasal Aspirator

Electronic Nasal Aspirator
Model : NS14

Manuctured for and Distributed by:
180° Innovations, Lakewood, CO 80215
Made in China

CONTENTS

Please read the instructions and warnings carefully before use to ensure safe and satisfactory operation of this product.

PRODUCT FEATURES

  1. Powerful Suction: Place aspiration tip into nostril to gently, yet powerfully remove nasal secretions.
  2. Safe: The soft aspiration tips are made from comfortable, latex-free, soft hygienic silicone to help prevent the possibility of injury when using the device. The tips are also dishwasher safe.
  3. Compact & Easy Design: This device is compact, easy to hold and operate and is safe and comfortable for use with infants or children.
  4. Washable Head Module Design: Tips, collection cup & removable head piece can be removed from the device and washed. (Collection cup can also be disinfected in boiling water.)
  5. Easy to Use: Simple operation.
  6. Battery Operated: This device uses two 1.5V AA batteries (included).

General Advice

The device is designed for using suction to remove nasal secretions and mucus in Children (age newborn to 12 years old) in your home environment.

  1. Do not expose the device to extreme temperature, very high humidity level, or direct sunlight.
  2. Avoid extreme shock, stress on or dropping of the device. It is not shock proof.
  3. Replace the batteries when the power and/or the sound of the pump weakens during the use of the device.
  4. It is recommended that you remove the batteries if the device will not be used for a period of time.
  5. Pressing and holding the power button starts the device and generates vacuum for the removal of nasal secretions and mucus. To stop the suction, simply release the power button to turn it off.
  6. Only a few seconds of suction at a time are necessary.
  7. This Nasal Aspirator is for cleaning/removal of nasal secretions only. Do not use this device other than for its intended purposes.
  8. During the use of the device, the baby/child should not hold their breath, close their mouth or swallow. This will help to avoid vacuum pressure resulting in an eardrum pressure imbalance.
  9. If the baby/child does not feel well when using the device, stop and consult a doctor immediately.
  10. Do not apply excessive force when placing the aspiration tip into the nasal cavity.
  11. This device is for home use only. Please consult a doctor in case of nasal diseases.
  12. The aspirator tips should be cleaned after each and every use.
  13. The operators of this device shall be adults or individuals who can follow the instructions and notices outlined in this user’s manual. This device is not intended for use by children themselves. Keep the nasal aspirator stored away from children. Children should NEVER operate the device themselves.

14. DO NOT use the Nasal Aspirator when the baby/child has the following contraindications:

  • Nasal bleeding
  • Acute head, facial, or neck injury
  • Coagulopathy or bleeding disorder

15 .Before using the device, please read this User’s Manual carefully. Incorrect use of the device may cause the following hazards/complications:

  • Mechanical trauma
  • Nasal irritation/bleeding
  • Mucosal hemorrhage
  • Discomfort and pain

NOTE: This Nasal Aspirator must only be used with the tips supplied with the device.

WARNINGS

Failure to follow these warnings and the assembly instructions could result in serious injury or death. Modifications not authorized by the manufacturer may void user’s authority to operate this device.

  • WARNING: This product is not a toy. Do not allow children to play with it. Individual parts may present a choking hazard.
  • Keep Nasal Aspirator away from heat sources, such as fireplaces, radiators, stoves, and TVs or other appliances. Heat can damage the case or electrical parts.
  • DO NOT use the Nasal Aspirator Unit if it has been dropped or is damaged.
  • DO NOT OPEN THE NASAL ASPIRATOR. There are NO user-serviceable parts inside the unit. Risk of electrical shock, fire or death.
  • Do not drop the device! Protect it from severe impact and shock. Keep out of the reach of children when not in use.
  • NOTE: Do not microwave.
  • CAUTION: Never insert the aspirator too far into the nostril. Never place the tip firmly against the inside wall of the nostril. This aspirator is for cleaning congestion in nasal passages.
  • Do not use this device for anything other than its intended purpose. Do not modify this device in any way.
  • NEVER use on ears, mouth, or eyes.
  • NOTE: Please consult with your physician on when and how often you should aspirate your baby/child’s nasal passages.

Product Overview

Product Overview

Battery Installation/Replacement

Recommended battery type – alkaline, size AA 1.5 VDC.
Change batteries when product ceases to operate satisfactorily.

  1. Loosen Battery Cover Screw and remove the battery cover as shown below.
  2. Requires two 1.5V alkaline AA size batteries (included).
  3. Clean the battery ends as well as the contacts in the device prior to installing or re-installing batteries (use a cotton swab slightly dampened with rubbing alcohol).
  4. Insert two new batteries being careful to match the correct polarities (+ and -).
  5. Firmly press the batteries to make sure they are completely inserted.
  6. Replace the battery cover making sure to insert Tab into Notch and then press until the cover clicks into place. Tighten the screw.
Battery Installation

Battery Safety

  • When changing the batteries, use batteries of the same type, make and capacity.
  • Always replace both batteries at the same time.
  • Never mix alkaline, standard carbon-zinc or rechargeable batteries in the same device. Do not mix old and new batteries.
  • Use batteries free of heavy metals.
  • Dispose of used batteries in accordance to your state and local regulations. Never dispose of batteries in the normal household waste.
  • Keep the batteries out of children’s reach.
  • Batteries may leak battery acid; 1. if mixed with a different battery type, if inserted incorrectly (put in backwards) or 2. if all batteries are not replaced or recharged at the same time.
  • Batteries may explode or leak battery acid if disposed of in fire or when charging a battery that is not specifically made to be recharged. Never recharge a cell of one type in a recharger made for a cell of another type.
  • Discard leaky batteries immediately. They can cause skin burns or other injury. When discarding batteries, be sure to dispose of them in the proper manner, according to your state and local regulations.
  • Always remove batteries before storing or if product will not be used for a prolonged period of time. Batteries left in the unit may leak and cause damage.

Instruction for Use

  1. There are two Tips to choose from. The large tip is recommended for use when the mucus is in a thicker, more solid form. The narrow tip is recommended for use when the mucus is loose and in a liquid form or when nostril opening is smaller.
Tip

2. Be sure to place the tip securely on the aspirator. The Tip must completely cover the rib before using.

cover the rib before using

3. Hold the baby/child upright and insert the tip into the nostril until the tip seals the nostril. Be careful not to place the tip too far into the nostril or press against the inside wall of the nostril.

4. Press and hold the power button to activate and allow the suction to clear the mucus. Only a few seconds of suction at a time are necessary. Repeat in the other nostril or as needed.

Press and hold the power
button

HELPFUL HINTS:

  • If needed, block the opposite nostril for more effective suctioning.
  • A small amount of saline mist may help to loosen thicker mucus.
  • Opening the baby/child’s mouth will help reduce ear pressure discomfort.

Note: The mucus may not immediately appear in the collection cup. After each use we recommend a quick cleaning of the used tip by removing it from the unit and thoroughly rinsing under warm tap.

Care and Cleaning

  1. Separate the suction portion from the base of the aspirator by gently pulling it apart.
  2. Unscrew collection cup by turning it counter clockwise.
  3. Remove white rubber ring located where collection cup screws in.
Care and Cleaning

4. Cleaning the Base: Wipe the unit with a clean soft dry cloth.

NEVER WASH THE BASE WITH WATER OR ANY LIQUID

NEVER WASH THE BASE WITH WATER OR ANY LIQUID

5. Cleaning the Suction Portion: Wash the collection cup, silicone ring and aspirator tips with mild soap and water and rinse thoroughly with running hot tap water for 3 minutes.

6. Rinse the Removable Head Piece with running hot tap water only for 3 minutes.

7. Let all pieces thoroughly air dry before re-assembling.

NOTES:

  • Never use any cleaners or solutions other than mild soap and water.
  • After cleaning, the collection cup and silicone ring may be disinfected by boiling in water.
  • NEVER boil the Removable Head Piece or the Non-return Tube. They may be damaged if overheated.
  • Nasal Tips ONLY are dishwasher safe.

Technical Specifications

Technical Specifications

EMC Tables

EMC Tables
EMC Tables
EMC Tables

Limited Warranty

This NS14 Nasal Aspirator (batteries excluded) is guaranteed for one year from the date of purchase against manufacturer’s defect under normal, household use and without evidence of tampering.

WARRANTY EXCLUSIONS: Device shows any signs of tampering or attempted modification. Evidence of improper handling or storing, such as dropping, heat, liquid or cleaner damage. Damage caused by natural disasters (fire, flood, earthquake, lightening). No receipt or proof of purchase showing date of purchase.

Following the directions closely will ensure years of dependable operation. If the NS14 Nasal Aspirator does not function properly, first check the batteries (see battery installation/replacement instructions). Replace the batteries if necessary.

Questions about your Manual ? Post in the comments!

Infrared Ear Thermometer KI-8190 Instruction Manual

Infrared Ear Thermometer KI-8190

INSTRUCTION MANUAL

Infrared Ear Thermometer

Infrared Ear Thermometer
KI-8190

PRECAUTION:
1. Please consult your physician to verify your body temperature.
2. D0 NOT scrape or scratch the lens as it will hamper the effectiveness of the device.
3. The device is intended for consumer use only.
4. Calibration is recommended every two years.

POWER SOURCE SIZE AAA (1.5V) x 2
WARRANTY: LIMITED ONE YEAR FROM THE DATE OF PURCHASE

Parts Identification

Parts Identification

Why an IR ear thermometer?
The tympanic membrane (eardrum), and the hypothalamus, the part of the brain which controls body temperature, share a common blood supply so tympanic readings rise and fall rapidly with core temperature (deep body temperature). This makes the ear temperatures one of the best indicators of internal body (core) temperature.

What are normal temperature values?
Human body temperature varies from person to person, some run in the lower range (96-97°F) and some run in the higher range (98-99°F). Also, your normal body temperature changes throughout the day and can vary at different times of the year. It is very important to know your normal body temperature range. We recommend measuring yourself when healthy to establish reference temperatures. This will help you feel more confident of the measured temperature readings when ill.

Information You Should Know Before Operating the IR Ear Thermometer
How to correctly use the IR ear thermometer

  1. It is useful to try this thermometer on yourself first to become familiar with it’s operations.
  2. Do not take the temperature immediately upon waking. Sleeping on the ear can cause the temperature to be higher than normal.
  3. It is common for the readings to be slightly different between the right and left ear. We suggest using the same ear to obtain temperature readings.
  4. Straighten the ear canal for measuring:
    Children under 12 months: Straighten ear canal by gently pulling the ear back.
Ear Back

Children over 12 months and Adults: Straighten the ear canal by gently pulling the ear back and up.

Ear Back and Up

5. This IR ear thermometer automatically converts the measured ear temperature reading to oral temperature.

6. Make sure the ear canal is dry, clean and free of wax or particulates.

Batteries
INSTALLING/REPLACING THE BATTERY

  1. Pull the battery cover off in the direction shown.
  2. Prior to installing new batteries you rnust clean the metal contact ends of the batteries and the metal springs and contacts for the batteries in the battery compartment.
  3. Install 2 new “AAA” batteries into the battery compartment matching correct polarities.
  4. Replace the battery cover securely.

WARNING: Do not put used batteries in trash. Recycle or manage as hazardous waste. Never dispose of batteries in fire. Dispose in recycling trash only. Do not recharge, put in backwards or disassemble. This may cause explosion, leakage and injury.

CAUTION: When replacing batteries, do not mix old ones and new ones. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.

Batteries

How to Operate the Thermometer

  1. Press and release the Power button to turn o n the unit. (Figure 11 A beep is heard. After about 2 seconds, the display shows that the unit is ready for measurement. (Figure 2)
  2. Place the probe into the ear canal then press and release the Power Button again to start measuring.
  3. While it is measuring, the display will show an “arrow” sign. (Figure 3)
  4. 4. A”beep-beep”sound is heard when the measurement is completed. (Figure 41
  5. The temperature and back light color shows on the display. The back light color will light according to the reading:
How to Operate the Thermometer

6. If the temperature reading is above 99.5°F, eight consecutive beeps will be heard to indicate fever alarm.
7. After the happy face stops flashing, You can repeat measurement by pressing the Power button again.
8. T urn off the unit by pressing and holding the Power button for 3 seconds until the OFF message is displayed. Along beep is heard. (Figure 5)

How to Operate the Thermometer

For Centigrade and Fahrenheit Switchable Models:
The Centigrade or Fahrenheit mode can be switched by turning the unit on then pressing the POWER button again immediately and holding it down. The display will show ‘CH’ with “F. or”C”. Release the button when the mode you desire is in the display window. The unit will show “L” with the degree sign and the happy face symbol in the display and is ready to take a new temperature reading.

For Centigrade and Fahrenheit Switchable Models

OPERATIONAL HINTS:

  1. Between each measurement, please allow a 5-second interval in order to obtain the most accurate result.
  2. Ensure that the probe lens is clean before each measurement. Dirty probe lens may cause inaccurate measurement.
  3. Because the thermometer is a very sensitive device, it must be at room temperature (approx. 60.8 – 104.°F) for at least 30 minutes before using to avoid any incorrect measurements.

Warning:
Performance of the device may be degraded if the device is operated or stored outside the stated temperature and humidity range of if the patient’s temperature is below ambient (room) temperature.

Memory Mode

Memory Mode
Memory Mode

Cleaning and Care

Cleaning and Care
Cleaning and Care

Error Message

Error Message

Specification

Specification

Limited Warranty
This device (batteries excluded) is guaranteed for one year from the date of purchase against manufacturers defect under normal use and without evidence of tampering.

WARRANTY EXCLUSIONS:
• Device Is not properly operated according to the instructions as described in this manual.
• Device shows any signs of tampering or attempted modification.
• Evidence of improper handling or storing, such as dropping, heat, liquid or cleaner damage.
• Natural disasters (such as fire, flood, earthquake, lightening).
• Nornelptor proof of purchase showing dote of purchase

Following the instructions closely will ensure years of dependable operation.

Explanation of Symbol

FCC STATEMENT

NOTE POTENTIAL FOR FrADICITTELEVISION
INTERFERENCE (for USA Only)

Operation is subject to the fallowing two conditions 1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and found . comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential Installation. The product generates, uses, and can radials radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, Mere is no guarantee that in.rference will not occur in a particular instelatiorc If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on and off, the user is encouraged to try to correct ale interference by one or more of Me following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receives
• Consult the dealer or an experienced redid. technician for help.

Changes or modifications not expressly approved by the party responsible for compliance or could void the users authority to operate the equipment.

Questions about your Manual ? Post in the comments!

Infrared Ear Thermometer KI-8170L Instruction Manual

Infrared Ear Thermometer KI-8170L

Instruction Manual

Infrared Ear Thermometer KI-8170

Infrared Ear Thermometer
Model KI-8170L

Precautions

  1. Please consult your physician to verify your body temperature.
  2. DO NOT scrape or scratch the lens as it will hamper the effectiveness of the device.
  3. The device is intended for consumer-use only.
  4. Calibration is recommended every two years.
  5. Do not drop or expose thermometer to electric shock as this may adversely affect its performance

POWER SOURCE SIZE AAA (1.5V) x 2
WARRANTY: ONE YEAR FROM THE DATE OF PURCHASE

Parts Identification

Parts Identification

Why IR ear thermometer?
The tympanic membrane (eardrum), and the hypothalamus, the part of the brain which controls body temperature, share a common blood supply, so tympanic readings rise and fall rapidly with core temperature (deep-body temperature). This makes the ear temperatures one of the best indicators of internal body (core) temperature.

What are normal temperature values?
Human body temperature varies from person to person. One person’s body temperatures are different from time to time. Therefore, it is very important to know your normal body temperature range. Because of this, we recommend that you measure yourself when healthy to establish reference temperatures which will make you feel more confident of the measured temperature when ill.

Information You Should Know Before Operating the IR Ear Thermometer
How to use the IR ear thermometer correctly?
1. It is useful to try this thermometer on yourself first to become familiar with its operations.
2. Please do not take the temperature immediately after waking up. Sleeping on the ear may cause the temperature to be higher than normal.
3. It is common for the readings to be slightly different between the right and the left ear. Therefore, we suggest using the same ear to obtain temperature.
4. To make the ear canal straight for measurement:
For Children under 12 months: Make the ear canal straight by pulling the ear back.

Ear Back

For Children over 12 months and Adults: Make the ear canal straight by pulling the ear back and up.

Ear Back and Up

Preparation for Use
Installing/Replacing the Battery

  1. Pull the battery cover off in the direction shown.
  2. Clean the battery contacts and also those of the device prior to battery re-installation.
  3. Install two new “AAA” batteries into the battery compartment matching correct polarities.
    4.Replace and fasten the battery cover securely.

Warning:
Batteries contain mercury. Refer to your local disposal laws for proper disposition. Manage as hazardous waste. Do not recharge, put in backwards, disassemble or dispose of batteries in fire. This may cause explosion, leakage and injury.

Caution:
When replacing batteries, do not mix old ones and new ones. Do not mix alkaline, standard(carbon-zinc) or rechargeable(nickel-cadmium) batteries.

Replacing the Battery

How to Operate the Thermometer

  1. Press and release the START/STOP button to turn on the unit. (F igure 1 ) A beep is heard. After about 2 seconds, the display shows that the unit is ready for measurement. (F igure 2 )
  2. Place the probe into the ear canal then press and release the START/STOP button again to start measurement.
  3. While it is measuring, the display will show an “arrow” sign. (F ig u re 3 )
  4. A “beep-beep”sound is heard when the measurement is completed. (F ig u re 4 )
  5. The temperature and back light color shows on the display. The display will light up according to the reading.

Please refer to Table 1

Table 1

6. After the smiling face symbol stops flashing, you can repeat measurement by pressing the START/STOP button again.

7. Turn off the unit by pressing and holding the START/STOP button for 5 seconds until the OFF message is displayed. A long beep is heard. (F igure 5 )

START

For Fahrenheit and Centigrade Switchable Models:
The Centigrade or Fahrenheit mode can be switched by turning the unit on then pressing the START/STOP button again immediately and holding it down. The display will show “CH” with “F” or”C”. Release the button when the mode you desire is in the display window. The unit will show “L” with the degree sign and the smiling face symbol in the display and is ready to take a new temperature reading.

For Fahrenheit and Centigrade

IMPORTANT THINGS TO KNOW

• Allow at least 1-3 minutes between each measurement in order to obtain the most accurate result.
• Make sure the probe lens is clean and clear before use. It should be ‘mirror like’ or reflective. A dirty, blocked or scratched lens will cause incorrect results.
• Do not store the device in extreme conditions or temperatures (ie., direct sunlight, very hot/cold or high moisture like a bathroom). Unit is not waterproof.
• If it has been stored in extreme conditions, wait at least one hour for it to return to a normal room temperature before using.
• Wait at least thirty minutes after bathing, exercising or eating before taking a measurement.
• Do not dismantle or modify the device other than changing the batteries.
• This device has no user serviceable parts. Do not dismantle or modify other than changing the batteries.

WARNING:
Performance of the device may be degraded if it is operated or stored outside the stated temperature and humidity range or if the patient’s temperature is below the ambient (room) temperature.

Memory Mode

Memory Mode
Deleting Memories
Cleaning and Care

Error Message

Error Message

Specification

Specification

Limited Warranty
This device (batteries excluded) is guaranteed for one year from the date of purchase against manufacturer’s defect under normal use and without evidence of tampering.

WARRANTY EXCLUSIONS:
• Device is not properly operated according to the instructions as described in this manual.
• Device shows any signs of tampering or attempted modification.
▪ Evidence of improper handling or storing, such as dropping, heat, liquid or cleaner damage.
▪ Natural disasters (such as fire, flood, earthquake, lightening). No receipt or proof of purchase showing date of purchase

Following the instructions closely will ensure years of dependable operation.

FCC STATEMENT
NOTE:
POTENTIAL FOR RADIO/TELEVSION INTERFERENCE (for U.S.A. Only)

Operation is subject to the following two conditions 1)This device may not cause harmful Interference, and 2) this device must accept any interference received, including interference That may cause undesired operation.

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the product does cause harmful interference to radio or television rception, which can be determined by turning the product on and off, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

Questions about your Manual ? Post in the comments!

Infrared Ear Thermometer KI-8170 Instruction Manual

Infrared Ear Thermometer KI-8170

Instruction Manual

Infrared Ear Thermometer KI-8170

Infrared Ear Thermometer
Model KI-8170

Precautions
1. Please consult your physician to verify your body temperature.
2. D0 NOT scrape or scratch the lens as it will hamper the effectiveness of the device.
3. The device is intended for consumer-use only.
4. Calibration is recommended every two years.

POWER SOURCE
SIZE AAA (1.5V)X2

WARRANTY:
One YEARS FROM THE DATE OF PURCHASE

Parts Identification

Parts Identification

Why IR ear thermometer?
The tympanic membrane (eardrum), and the hypothalamus, the part of the brain which controls body temperature, share a common blood supply, so tympanic readings rise and fall rapidly with core temperature (deep-body temperature). This makes the ear temperatures one of the best indicators of internal body (core) temperature.

What are normal temperature values?
Human body temperature varies from person to person. One person’s body temperatures are different from time to time. Therefore, it is very important to know your normal body temperature range. Because of this, we recommend that you measure yourself when healthy to establish reference temperatures which will make you feel more confident of the measured temperature when ill.

Information You Should Know Before Operating the IR Ear Thermometer
How to use the IR ear thermometer correctly?
1. It is useful to try this thermometer on yourself first to become familiar with its operations.
2. Please do not take the temperature immediately after waking up. Sleeping on the ear may cause the temperature to be higher than normal.
3. It is common for the readings to be slightly different between the right and the left ear. Therefore, we suggest using the same ear to obtain temperature.
4. To make the ear canal straight for measurement: For Children under 12 months: Make the ear canal straight by pulling the ear back.

Ear Back

For Children over l 2 months and Adults: Make the ear canal straight by pulling the ear back and up.

Ear Back and Up

Preparation for Use
Installing/Replacing the Battery

  1. Slide the battery cover off in the direction shown.
  2. Clean the battery contacts and also those of the device prior to battery re-installation.
  3. Install two new “AAA* batteries into the battery compartment matching correct polarities.
    4.Replace and fasten the battery cover securely.

WARNING:
Batteries contain mercury. Do not put in household trash. Manage as hazardous waste. Never dispose of in fire. Do not recharge, put in backwards or disassemble, as this may cause explosion, leakage and injury.

Caution:
When replacing batteries, do not mix old ones and new ones. Do not mix alkaline, standard(carbon-zinc) or rechargeable(nickel-cadmium) batteries.

Replacing the Battery

How to Operate the Thermometer

  1. Press and release the START/STOP button to turn on the unit. (Figurel) A beep is heard. After about 2 seconds, the display shows that the unit is ready for measurement. (Figure2)
  2. Place the probe into the ear canal then press and release the START/STOP button again to start measurement.
  3. While it is measuring, the display will show an “arrow” sign. (Figure3)
  4. A “beep-beep”sound is heard when the measurement is completed. (Flgure4)
  5. After the smiling face symbol stops flashing, you can repeat measurement by pressing the START/STOP button again.
  6. Turn off the unit by pressing and holding the START/STOP button for 3 seconds until the OFF message is displayed. A long beep is heard. (Figure5)
How to Operate the Thermometer

For Centigrade and Fahrenheit Switchable Models: The Centigrade or Fahrenheit mode can be switched by turning the unit on then pressing the START/STOP button again immediately and holding it down. The display will show “CH” with “F” or”C”. Release the button when the mode you desire is in the display window. The unit will show “L” with the degree sign and the smiling face symbol in the display and is ready to take a new temperature reading.

Switchable Models

Operational Hints:

  1. Between each measurement, please allow a 5-second interval in order to obtain the most accurate result.
  2. Ensure that the probe lens is clean before each measurement. Dirty probe lens may cause Inaccurate measurement.
  3. Because the thermometer is a very sensitive device, it must be at room temperature approx. 60.8-104°F (16-40°C) for at least 30 minutes before using to avoid any incorrect measurements.

Warning:
Performance of the device may be degraded if the device is operated or stored outside the stated temperature and humidity range or if the patient’s temperature is below ambient (room) temperature.

Memory Mode
Recalling Memory:

  1. If the power is on, turn off the power first.
  2. Press and hold the START/STOP button for about 3 seconds until the last recorded temperature is displayed.
Memory

3. For models with 9 memories Press the START/STOP button repeatedly will take you to each recorded temperature in the memory. you may toggle the button to see the recorded temperatures.

recorded temperatures

4. After you release the START/STOP button the unit will return to the measurement mode.

measurement

5. “L” will appear on the display. The unit is then ready for Measurement again.

Measurement again

6. It is now ready to take a new temperature reading.

Memory Mode

Cleaning and Care

Cleaning and Care

Error Massage

Error Massage

Specification

Specification

Limited Warranty
This device (batteries excluded) is guaranteed for one year from the date of purchase against manufacturer’s defect under normal use and without evidence of tampering.

WARRANTY EXCLUSIONS:
• Device is not properly operated according to the instructions as described in this manual.
• Device shows any signs of tampering or attempted modification.
▪ Evidence of improper handling or storing, such as dropping, heat, liquid or cleaner damage.
▪ Natural disasters (such as fire, flood, earthquake, lightening). No receipt or proof of purchase showing date of purchase

Following the instructions closely will ensure years of dependable operation.

FCC STATEMENT
NOTE:
POTENTIAL FOR RADIO/TELEVSION INTERFERENCE (for U.S.A. Only)

Operation is subject to the following two conditions 1)This device may not cause harmful Interference, and 2) this device must accept any interference received, including interference That may cause undesired operation.

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the product does cause harmful interference to radio or television rception, which can be determined by turning the product on and off, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

Questions about your Manual ? Post in the comments!

Infrared Ear Thermometer KI-8160 Instruction Manual

Infrared Ear Thermometer KI-8160

Instruction Manual

Infrared Ear Thermometer KI-8160

Infrared Ear Thermometer
Model KI-8160

Precautions
1. Please consult your physician to verify your body temperature.
2. D0 NOT scrape or scratch the lens as it will hamper the effectiveness of the device.
3. The device is intended for consumer-use only.
4. Calibration is recommended every two years.

POWER SOURCE
SIZE CR2032 (3.0 VDC)
LITHIUM BATTERY (1)

WARRANTY:
TWO YEARS FROM THE DATE OF PURCHASE

Parts Identification

Parts Identification

Why IR ear thermometer?
The tympanic membrane (eardrum), and the hypothalamus, the part of the brain which controls body temperature, share a common blood supply, so tympanic readings rise and fall rapidly with core temperature (deep-body temperature). This makes the ear temperatures one of the best indicators of internal body (core) temperature.

What are normal temperature values?
Human body temperature varies from person to person. One person’s body temperatures are different from time to time. Therefore, it is very important to know your normal body temperature range. Because of this, we recommend that you measure yourself when healthy to establish reference temperatures which will make you feel more confident of the measured temperature when ill.

Information You Should Know Before Operating the IR Ear Thermometer
How to use the IR ear thermometer correctly?
1. It is useful to try this thermometer on yourself first to become familiar with its operations.
2. Please do not take the temperature immediately after waking up. Sleeping on the ear may cause the temperature to be higher than normal.
3. It is common for the readings to be slightly different between the right and the left ear. Therefore, we suggest using the same ear to obtain temperature.
4. To make the ear canal straight for measurement:

For Children under 12 months: Make the ear canal straight by pulling the ear back.

Ear Back

For Children over l 2 months and Adults: Make the ear canal straight by pulling the ear back and up.

Ear back and Up

5. This IR ear thermometer automatically converts measured ear temperature reading to oral temperature.

Preparation for Use
Installing/Replacing the Battery

  1. Use a pointed object such as the tip of a pen to push down on the battery cover lock.
  2. Pull the cover off while the cover lock is pushed down.
  3. Extract the battery from the battery holder with an insulated instrument. Avoid using any sharp metal object in this operation. Discard old battery properly.
  4. Place one new 3 VDC lithium battery CR2032 or equivalent into the chamber with the positive (+) side up and the negative (-) side down.
  5. Replace and fasten the battery cover. securely.

Warning :
Battery Contains Mercury. Do Not Put in Trash. Recycle or Manage as Hazardous Waste. Never dispose of battery in fire. Dispose in recycling trash only. Do not recharge, put in backwards or disassemble. This may cause explosion, leakage and injury.

Warning

How to Operate the Thermometer

  1. Press and release the START/STOP button to turn on the unit. (Figurel) A beep is heard. After about 2 seconds, the display shows that the unit is ready for measurement. (Figure2)
  2. Place the probe into the ear canal then press and release the START/STOP button again to start measurement.
  3. While it is measuring, the display will show an “arrow” sign. (Figure3)
  4. A “beep-beep”sound is heard when the measurement is completed. (Flgure4)
  5. After the smiling face symbol stops flashing, you can repeat measurement by pressing the START/STOP button again.
  6. Turn off the unit by pressing and holding the START/STOP button for 3 seconds until the OFF message is displayed. A long beep is heard. (Figure5)
How to Operate the Thermometer

For Centigrade and Fahrenheit Switchable Models: The Centigrade or Fahrenheit mode can be switched by turning the unit on then pressing the START/STOP button again immediately and holding it down. The display will show “CH” with “F” or”C”. Release the button when the mode you desire is in the display window. The unit will show “L” with the degree sign and the smiling face symbol in the display and is ready to take a new temperature reading.

Switchable Models

Operational Hints:

  1. Between each measurement, please allow a 5-second interval in order to obtain the most accurate result.
  2. Ensure that the probe lens is clean before each measurement. Dirty probe lens may cause Inaccurate measurement.
  3. Because the thermometer is a very sensitive device, it must be at room temperature approx. 60.8-104°F (16-40°C) for at least 30 minutes before using to avoid any incorrect measurements.

Warning:
Performance of the device may be degraded if the device is operated or stored outside the stated temperature and humidity range or if the patient’s temperature is below ambient (room) temperature.

Memory Mode
Recalling Memory:

  1. If the power is on, turn off the power first.
  2. Press and hold the START/STOP button for about 3 seconds until the last recorded temperature is displayed.
Memory

3. For models with 9 memories Press the START/STOP button repeatedly will take you to each recorded temperature in the memory. you may toggle the button to see the recorded temperatures.

recorded temperatures

4. After you release the START/STOP button the unit will return to the measurement mode.

measurement

5. “L” will appear on the display. The unit is then ready for Measurement again.

Measurement again

6. It is now ready to take a new temperature reading.

Memory Mode

Memory Mode

Cleaning and Care

Cleaning and Care

Error Massage

Error Massage

Specification

Specification

Limited Warranty
This device is guaranteed for one years from the date of purchase against manufacturer’s defect under normal, household use. Following the instructions closely will ensure years of dependable operation.

FCC STATEMENT

NOTE:

POTENTIAL FOR RADIO/TELEVSION INTERFERENCE (for U.S.A. Only)

Operation is subject to the following two conditions 1)This device may not cause harmful Interference, and 2) this device must accept any interference received, including interference That may cause undesired operation.

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the product does cause harmful interference to radio or television rception, which can be determined by turning the product on and off, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

Questions about your Manual ? Post in the comments!

Basal Digital Thermometer KD-2160 Instruction Manual

Basal Digital Thermometer KD-2160

Basal Digital Thermometer
KD-2160

INSTRUCTIONS FOR USE
Please read thoroughly before using

FEATURES

This basal digital thermometer is intended to measure the human body temperature for women. It’s precise digital display is for using in a household environment.

  1. Oral temperature measurement in approximately 30 seconds with proper use.
  2. 40 sets of memories. Recall all memories using NFC (Near Field Communication) or the headset jack adapter on your mobile device.
  3. Very sensitive unit, easy to read digital LCD (liquid crystal display).
  4. Compact, accurate and durable LSI (large scale integration) unit.
  5. If the thermometer is inadvertently left on after temperature stabilization, it will automatically shut off after approximately 3 minutes.
  6. Small, light weight unit with “store-away” probe and a handy carry case.
  7. ABS resin body presents no hazard compared to broken mercury/glass thermometers.
  8. Low battery indicator: when the symbol ” “appears , the battery needs to be replaced .

PARTS DESCRIPTION

PARTS DESCRIPTION

SPECIFICATIONS

SPECIFICATIONS

EXPLANATION OF SYMBOLS

EXPLANATION OF SYMBOLS

PRECAUTION

  1. Do not boil the probe. Instead, clean the unit by wiping it with a dry cloth and disinfect the probe with rubbing alcohol. See cleaning instructions for details.
  2. Do not drop the thermometer or expose it to heavy shock. The unit is not shock-proof.
  3. This unit is not water proof. Sensor and probe are water resistant.
  4. Do not bite or swallow the probe. Do not place the headset jack adaptor in mouth.
  5. After using, clean the thermometer and store it in the carrier case.
  6. Do not store the unit in direct sunlight, at a high temperature, in high humidity or dust.Performance may be degraded.
  7. Stop using the thermometer if it operates erratically or if the display malfunctions.
  8. Keep out of reach of children. Supervision is recommended at all times.
  9. Do not attempt to disassemble the unit except to replace the battery.
  10. If the thermometer has been stored outside the stated storage condition range of temperatures (see specifications), allow the thermometer to naturally return to room temperature before using.
  11. If the thermometer is operated outside the stated temperature and humidity ranges or if the patient’s temperature is below the ambient (room) temperature, performance of the device may be degraded.

BATTERY REPLACEMENT

  1. When the symbol ” ” appears, the battery needs to be replaced.
  2. Push and slide the battery cover as indicated below to open. Use a non-metal object inserted into the recessed notch to carefully lift the battery up and out of the unit. Do not lift the battery or remove from the opposite side as this may damage or break the metal tabs.
  3. Confirm the polarity of the battery is correct (positive + side up) and insert, again being careful not to damage the metal tabs. Replace the battery cover.
BATTERY REPLACEMENT

Warning:

  1. Discard old battery, out of reach of young children. Swallowing the battery may be fatal. If the battery is swallowed, contact a hospital immediately to have it removed. Do not dispose of the battery in a fire as it may explode.
  2. For battery disposition, please consider your local and state laws and regulations.

HOW TO USE

1.The probe is folded into the body of the thermometer for storage. Unfold the probe and disinfect with rubbing alcohol before using.

2. Press and release the on/off button. The display will read

HOW TO USE

3. Next the display will show L°F or L°C with the °F or °C flashing.

4. Place the probe under the tongue as described and shown below.

5. Once the degree sign °F (°C) on the display has stopped flashing, the measured temperature is indicated.

6. The unit will automatically turn off in approx. 3 minutes. However, to prolong battery life, it is best to turn off the thermometer by pressing the ON/OFF button once the temperature has been noted.

ORAL USE

ORAL USE

Place the probe well under the patient’s tongue with the probe sensor in the “heat pocket” (see diagram). Instruct the patient to keep their mouth closed while the thermometer is reading. You may find it necessary to hold the unit in place while it is reading, so you do not bite the probe. A normal temperature by this method is usually considered between 96.80°F to 99.50°F (36.00°C to 37.50°C).

Special Features:
Normal Temperature Alarm: An alarm will sound when the peak temperature has registered and is ready-to-read. The “Normal Temperature” alarm (four quick beeps followed by a pause) will sound repeatedly for approximately 5 seconds.

For Switchable Fahrenheit and Centigrade Models: After turning on or waking up the thermometer, the Fahrenheit or Centigrade mode can be switched within the first 2 seconds by pressing and holding the POWER button until you hear a beep and the F or C changes.

Temperature Memory Recall: When the unit is off or in clock mode, press the M button to view the most recent memory reading. Continue to press/release for viewing additional memory readings. Memory readings show from the most recent to the oldest and include the memory number and the corresponding temperature.

Temperature Memory Recall

User can record all memories on their mobile device with application software located on the OUcare website.

For information and help in using this thermometer with your mobile device, refer to the enclosed Quick Start Guide.

Setting:
The unit can be setup with the date, time and clock mode (on or off). The setting sequence is year, month, day, hour, minute and clock mode.

  1. With the unit in ‘off’ or ‘clock’ mode, press and hold the M button until the display shows a blinking year and press the POWER button for adjustment.
  2. After selecting the current year, press the M button to proceed to set the month, day etc., using the POWER button for adjustments.
Setting

NOTE : Always disinfect the thermometer before and after using.
NOTE : In Step 3, if the room temperature is greater than 90.00°F (32.00°C), it will be displayed rather than L°F (L°C).
NOTE : Before step 4, you may put a plastic sanitary probe cover on the sensor tip to help prevent cross-contamination and infection. Using a probe cover may result in a 0.2°F (0.1°C) difference from actual temperature. Dispose of used probe cover and store the unit in the case provided and in a safe place.

BODY TEMPERATURE FACTS
THE TAKING OF BODY TEMPERATURES: Changes in body temperature are one of the most important indicators of illness. It is important that accurate temperatures be taken. Even though the digital thermometer is used in similar manner to the glass thermometer, it is important that these simple instructions for use be followed closely and that the person taking the temperature understands body temperature.

BODY TEMPERATURE: A person’s body temperature will usually be several tenths to one full degree lower in the morning than it is in the late afternoon. Therefore, if your temperature is 97.88°F (36.60°C) in the morning, it could be 98.42°F (36.90°C) or more in the late afternoon and still be normal. To determine what your normal body temperature is you should take your temperature both in the early morning and in the late afternoon over several days. Children have the same normal temperature range as do adults. A fever for both children and adults is typically defined as a temperature over 99.50°F (37.50°C) [oral reading]. Exercise, excessive clothing, hot bath, hot weather, warm food and drink can all cause elevations of up to 100.40°F (38.00°C) to 101.12°F (38.40°C) in oral temperature. If you suspect one of these to be the cause of an elevated reading, eliminate the cause and retake the temperature in half an hour.

CLEANING INSTRUCTIONS
To clean the thermometer, wash the sensor with a solution of mild detergent and cool water. Disinfect the thermometer by wiping the sensor and probe with a cloth dipped in a household antiseptic solution such as rubbing alcohol.

LIMITED WARRANTY

This thermometer (batteryA excluded) is guaranteed for one year from the date of purchase against manufacturer’s defect under normal, household use and without evidence of tampering.

WARRANTY EXCLUSIONS:
• Device is not properly operated according to the instructions as described in this manual.
• Device shows any signs of tampering or attempted modification.
• Evidence of improper handling or storing, such as dropping, electric shock, heat, liquid or cleaner damage.
• Natural disasters (i.e., fire, flood, earthquake, lightening)
• No receipt or proof of purchase showing date of purchase

FOLLOWING THE INSTRUCTIONS CLOSELY WILL ENSURE YEARS OF DEPENDABLE OPERATION.

If the thermometer does not function properly, first check the battery (see battery replacement If the thermometer does not function properly, first check the battery (see battery replacement instructions). Replace if necessary.

FCC STATEMENT

NOTE: POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for USA Only)

Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the product and the receiver
• Consult the dealer or an experienced radio/TV technician for help

Questions about your Manual ? Post in the comments!

Basal Digital Thermometer KD-1342 Instruction Manual

Basal Digital Thermometer KD-1342

Basal Digital Thermometer
KD-1342

INSTRUCTIONS FOR USE
Please read carefully before using

FEATURES

  1. Easy to read digital LCD (liquid crystal display).
  2. Compact, accurate and durable LSI (large scale integration) device.
  3. Temperatures can be taken under the tongue ( oral use ) or under the arm (axillary use). It is suggested that rectal temperatures be taken on infants only when axillary use is inconvenient.
  4. Very sensitive device, quick to obtain results. Reads in around 60 seconds.
  5. If the thermometer is inadvertently left on after temperature stabilization, it will automatically shut off in about 9 minutes.
  6. Small, light weight unit. Universal use for the whole family, especially ideal for children.
  7. ABS resin body presents no hazard compared to broken mercury glass thermometers .
  8. Low battery indicator: when the symbol “IU” appears, the battery needs to be replaced.
  9. The unit is water resistant.

PARTS DESCRIPTION

PARTS DESCRIPTION

DEVICE DESCRIPTION AND INTENDED USE

The thermometer is an electronic device and it is intended to measure human body temperature either oral, rectal or axillaries. They are intended for using on people of all ages.

SPECIFICATIONS

SPECIFICATIONS

PRECAUTIONS

  1. Do not boil the probe. Instead , clean the unit by wiping it with a dry cloth and disinfect the probe with isopropyl( rubbing ) alcohol .
  2. Do not drop the thermometer or expose it to heavy impact. The unit is not impact-proof.
  3. Do not bend or bite the probe.
  4. Do not store the unit under direct sunlight, at a high temperature , in high humidity or dust. Performance may be degraded.
  5. Stop using the thermometer if it operates erratically or if the display malfunctions
  6. Keep out of reach of children.
  7. Clean the thermometer probe before storing.
  8. Do not attempt to disassemble the unit except to replace the battery.
  9. If the thermometer has been stored at below-freezing temperatures, allow the thermometer to warm naturally to room temperature before using.
  10. Performance of the device may be degraded if: Operated or stored outside stated temperature and humidity ranges or if the patient’s temperature is below the ambient(room) temperature.

BATTERY REPLACEMENT

  1. When the symbol” BATTERY COVER ” appears , the battery needs to be replaced.
  2. Unscrew the battery cover with a Phillips head screwdriver and remove it from the thermometer.
  3. Use a toothpick or insulated probe to remove the battery. Avoid using any sharp metal object in this operation.
  4. Clean the battery contacts and also those of the device prior to battery re-installation.
  5. Place a new battery in the chamber.
  6. Replace and fasten the battery cover securely by screw.
BATTERY REPLACEMENT

Warning :

  1. Discard old battery carefully , out of reach of young children. Swallowing the battery may be fatal. lithe battery is swallowed, contact a hospital immediately to have it removed. Do not dispose of the battery in a fire. It may explode.
  2. For battery disposition, please consider local disposal laws.

HOW TO USE

1.Disinfect the probe with isopropyl(rubbing) alcohol before using.

2. Depress the on/off button. The display will read

HOW TO USE

And Then

as a system check

as a system check.

3. Release the power switch and the display will show Lo°F(or Lo°C) with °F(°C) flashing.

4. Place the probe in the appropriate position (oral, axillary or rectal).

5. Once the degree sign °F(°C) on the display has stopped flashing (usually within 60 seconds) , the correct temperature is indicated. The temperature reading will not change after the °F(°C) stops flashing.

6. The unit will automatically turn off in 9 minutes (approx. ). However, to prolong battery life, it is best to turn off the thermometer once the temperature has been noted.

Special Features:
Normal Temperature Alarm: An alarm will sound when the peak temperature has registered and is ready-to-read. The “Normal Temperature” alarm (four quick beeps followed by a pause) will sound repeatedly for approximately 8 seconds.

Last-Temperature Memory Recall: When the ON/OFF button is depressed to activate the thermometer, hold down for approximately 5 seconds. The display of 188.88 will change to show the last measured temperature. This reading is displayed as long as the button is held down. When the button is released, the thermometer will be in “ready-to-measure” mode and the recalled temperature will be erased.

For Models with Fever Alarm: If the temperature registers higher than 99.50°F(37.50°C), the fever alarm (a quick beeping sound which occurs continuously for about 8 seconds) will sound when the peak temperature has registered. Also, the result will keep flashing until the thermometer is turned off.

NOTE : Always disinfect the thermometer before using.

NOTE: In Step 2, if the room temperature is greater than 89.60°F(32.00°C), it will be displayed rather than L°F(or L°C).

NOTE: In Step 3, you may put a sanitary plastic probe shield on the sensor tip to help prevent cross-infection and contamination. Use of the probe cover may result in a 0.20°F (0.10°C) difference from actual temperature. Dispose of any used probe shield and store the unit in a safe place.

RELIABLE METHODS TO MEASURE TEMPERATURE
THE TAKING OF BODY TEMPERATURES: Change in body temperature is one of the most important indicators of illness. It is important that accurate temperatures be taken. Even though the digital thermometer is used in similar manner to the glass thermometer, it is important that the simple instructions for use of this thermometer be followed closely and that the person taking the temperature understands body temperature.

BODY TEMPERATURE: A person’s body temperature will usually be several tenths to one full degree lower in the morning than it is in the late afternoon. Therefore, if your temperature is 97.9°F(36.6°C) in the morning, it could be 98.4°F(36.9°C) or more in the late afternoon and still be normal. To determine what your normal body temperature is you should take your temperature both in the early morning and in the late afternoon over several days. Children have the same normal temperature range as do adults. Afever for both children and adults is typically defined as a temperature over 99.5°F(37.5°C) (oral reading). Exercise, excessive clothing, hot bath, hot weather, warm food and drink can cause mild elevations of up to 100.4°F(38°C) to 101.1°F(38.4°C) in oral temperature. If you suspect one of these to be the cause of an elevated reading, eliminate the possible cause and retake the temperature in a half hour.

ORAL USE

ORAL USE

Place the probe well under the patient’s tongue. Instruct the patient to keep their mouth closed while the thermometer is reading. A normal temperature by this method is usually considered between 96.8°F to 99.5°F(36.0°C to 37.5°C).

RECTAL USE
If rectal temperature is recommended by your doctor, you may use a probe shield. Insert thermometer into the probe shield. Lubricate the probe cover with a water soluble jelly for easier insertion. Do not use petroleum jelly. Insert tip of probe no more than 1/2 inch into rectum. STOP if you meet any resistance. The sensing unit is on the very tip of the probe and there is no need to insert the probe deep into the rectum. In general, the rectal temperature is around 1.0 to 2.0°F(0.5°C to 1.0°C) higher than oral temperature.

AXILLARY USE
Wipe armpit with a dry towel . Place probe in the patient’s armpit and keep the patient’s arm pressed firmly against the body. In general, the axillary temperature is around 1.0 to 2.0°F(0.5°C to 1.0°C) lower than oral temperature. Note that in order to achieve better axillary temperature measurement result a minimum measuring time of 3-5 minutes is recommended regardless of the been sound.

NOTE : Children should be attended by an adult during the entire temperature recording process. After use, the digital thermometer should be stored in a safe place, out of reach of young children. If you compare temperatures between two thermometers, it is possible to have two different readings even if both thermometers are within their accuracy tolerances. Differences in how you take each reading and the thermometer’s tolerance range can account for nearly 0.2°F(0.1°C) variability.

CLEANING INSTRUCTIONS
To clean the thermometer, wash the tip with a solution of mild detergent and cool water. Disinfect the thermometer by wiping the sensor and lower stem with a cloth dipped in a household antiseptic solution such as rubbing alcohol.

LIMITED WARRANTY
This thermometer is guaranteed for one year from the date of purchase against manufacturers defect under normal, household use. Following the directions closely will ensure years of dependable operation. If the thermometer does not function properly, first check the battery (see battery replacement instructions). Replace it if necessary.

FCC STATEMENT
NOTE: POTENTIAL FOE RADIO/TELEVISION INTERFERENCE (for U.S.A. Only)

Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Thank you for purchasing a BESTMED product.

Questions about your Manual ? Post in the comments!

Basal Digital Thermometer KD-235 Instruction Manual

Basal Digital Thermometer KD-235, Instruction Manual, User Manual,Thermometer,KD-235,

Basal Digital Thermometer
KD-235

INSTRUCTIONS FOR USE
Please read carefully before using

FEATURES

  1. Easy to read digital LCD ( liquid crystal display ).
  2. Compact, accurate and durable LSI ( large scale integration ) device.
  3. Temperatures can be taken under the tongue ( oral use ) or under the arm (axillary use ). It is suggested that rectal temperatures be taken on infants only when axillary use is inconvenient.
  4. Very sensitive device, quick to obtain results.
  5. If the thermometer is inadvertently left on after temperature stabilization, it will automatically shut off in about 9 minutes.
  6. Small , light weight unit ( 11 grams ). Universal use for the whole family, especially ideal for children.
  7. ABS resin body presents no hazard compared to broken mercury glass thermometers .
  8. Low battery indicator: when the symbol ” BATTERY COVER” appears, the battery needs to be replaced.

PARTS DESCRIPTION

PARTS DESCRIPTION

SPECIFICATIONS

SPECIFICATIONS

PRECAUTIONS

  1. Do not boil the probe . Instead , clean the unit by wiping it with a dry cloth and disinfect the probe with isopropyl( rubbing ) alcohol .
  2. Do not drop the thermometer or expose it to heavy shock . The unit is not shock-proof .
  3. Do not bend or bite the probe .
  4. Do not store the unit under direct sunlight, at a high temperature , in high humidity or dust. Performance may be degraded.
  5. Stop using the thermometer if it operates erratically or if the display malfunctions .
  6. Keep out of reach of unsupervised children .
  7. Clean the thermometer probe before storing .
  8. Do not attempt to disassemble the unit except to replace the battery .
  9. If the thermometer has been stored at below-freezing temperatures, allow the thermometer to warm naturally to room temperature before using .
  10. Performance of the device may be degraded if : Operated or stored outside stated temperature and humidity ranges or if the patient’s temperature is below the ambient(room) temperature.

BATTERY REPLACEMENT

  1. When the symbol “BATTERY COVER” appears , the battery needs to be replaced .
  2. Pull the battery cover off in the direction shown.
  3. Use a toothpick or insulated probe to remove the battery. Avoid using any sharp metal object in this operation.
  4. Clean the battery contacts and also those of the device prior to battery re-installation.
  5. Place a new 1.55 VDC button size battery type Micro Alkaline battery 192 ,LR41 or equivalent in the chamber with the positive sideNup and the negative side(-) down.
  6. Replace and fasten the battery cover securely.
BATTERY REPLACEMENT

Warning :
Discard old battery carefully, out of reach of young children. Swallowing the battery may be fatal. If the battery is swallowed, contact hospital immediately to have it removed. Do not dispose of the battery in a fire. It may explode.

HOW TO USE

1.Disinfect the probe with isopropyl(rubbing) alcohol before using.

2. Depress the on/off button. The display will read

How to Use

3. Release the power switch and the display will show L°C(or L°F) with °C(°F) flashing.

4. Place the probe in the appropriate position (oral, axillary or rectal).

5. Once the degree sign °C(°F) on the display has stopped flashing (usually within 40-120 seconds ) , the correct temperature is indicated. The temperature reading will not change after the °C(°F) stops flashing.

6. The unit will automatically turn off in 9 minutes ( approx. ). However, to prolong battery life, it is best to turn off the thermometer once the temperature has been noted.

Special Features:
Normal Temperature Alarm: An alarm will sound when the peak temperature has registered and is ready-to-read. The “Normal Temperature” alarm (four quick beeps followed by a pause) will sound repeatedly for approximately 8 seconds.

Last-Temperature Memory Recall: When the ON/OFF button is depressed to activate the thermometer, hold down for approximately 5 seconds. The display of 188.88 will change to show the last measured temperature. This reading is displayed as long as the button is held down. When the button is released, the thermometer will be in “ready-to-measure” mode and the recalled temperature will be erased. For Models with Fever Alarm If the temperature registers higher than 37.50°C(99.50°F), the fever alarm (a quick beeping sound which occurs continuously for about 8 seconds) will sound when the peak temperature has registered. Also, the result will keep flashing until the thermometer is turned off.

To change the scale from Fahrenheit (°F) to Centigrade (“C): After turning the thermometer on, immediately press the ON/OFF button again and hold until the °F changes to a °C. After releasing the ON/OFF button the display will show an L with a flashing °F or °C. The device is now ready to record and display a temperature. Follow the same directions to switch back from Centigrade to Fahrenheit.

NOTE : Always disinfect the thermometer before using.

NOTE : In Step 2, if the room temperature is greater than 32.00°C (89.60°F), it will be displayed rather than L°C(or L°F).

NOTE : In Step 3, you may put a sanitary plastic probe shield on the sensor tip to help prevent cross-infection and contamination. Use of the probe cover may result in a 0.10°C (0.20°F) difference from actual temperature. Dispose of any used probe shield and store the unit in a safe place.

RELIABLE METHODS TO MEASURE TEMPERATURE
THE TAKING OF BODY TEMPERATURES: Change in body temperature is one of the most important indicators of illness. It is important that accurate temperatures be taken. Even though the digital thermometer is used in similar manner to the glass thermometer, it is important that the simple instructions for use of this thermometer be followed closely and that the person taking the temperature understands body temperature.

BODY TEMPERATURE: A person’s body temperature will usually be several tenths to one full degree lower in the morning than it is in the late afternoon. Therefore, if your temperature is 36.60°C(97.88°F) in the morning, it could be 36.90°C(98.42°F) or more in the late afternoon and still be normal. To determine what your normal body temperature is you should take your temperature both in the early morning and in the late afternoon over several days. Children have the same normal temperature range as do adults. A fever for both children and adults is typically defined as a temperature over 37.50°C(99.50°F) (oral reading). Exercise, excessive clothing, hot bath, hot weather, warm food and drink can cause mild elevations of up to 38.00°C(100.40°F) to 38.40°C(101.12°F) in oral temperature. If you suspect one of these to be the cause of an elevated reading, eliminate the possible cause and retake the temperature in a half hour.

ORAL USE

ORAL USE

Place the probe well under the patient’s tongue. Instruct the patient to keep their mouth closed while the thermometer is reading. A normal temperature by this method is usually considered between 36.00°C to 37.50°C(96.80°F to 99.50°F).

RECTAL USE
If rectal temperature is recommended by your doctor, you may use a probe shield. Insert thermometer into the probe shield. Lubricate the probe cover with a water soluble jelly for easier insertion . Do not use petroleum jelly . Insert tip of probe no more than 1/2 inch into rectum . STOP if you meet any resistance . The sensing unit is on the very tip of the probe and there is no need to insert the probe deep into the rectum . In general, the rectal temperature is around 0.50°C to 1.00°C(1.00 to 2.00°F) higher than oral temperature.

AXILLARY USE
Wipe armpit with a dry towel . Place probe in the patient’s armpit and keep the patient’s arm pressed firmly against the body. In general, the axillary temperature is around 0.50°C to 1.00°C(1.00 to 2.00°F) lower than oral temperature. Note that in order to achieve better axillary temperature measurement result a minimum measuring time of 2-3 minutes is recommended regardless of the beep sound.

NOTE : Children should be attended by an adult during the entire temperature recording process . After use , the digital thermometer should be stored in a safe place, out of reach of young children. If you compare temperatures between two thermometers , it is possible to have two different readings even if both thermometers are within their accuracy tolerances. Differences in how you take each reading and the thermometer’s tolerance range can account for nearly 0.10°C(0.20°F) variability.

CLEANING INSTRUCTIONS
To clean the thermometer, wash the tip with a solution of mild detergent and cool water. Disinfect the thermometer by wiping the sensor and lower stem with a cloth dipped in a household antiseptic solution such as rubbing alcohol.

LIMITED WARRANTY
This thermometer has a Lifetime Warranty against manufacturer ‘s defect under normal, household use. Follow the direct ions closely will ensure years of dependable operation.

lithe thermometer does not function properly, first check the battery (see battery replacement instructions). Replace it if necessary.

FCC STATEMENT

NOTE:
POTENTIAL FOR RADIO/TELEVSION INTERFERENCE (for U.S.A. Only)

Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna
Increase the separation between the product and the receiver.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Questions about your Manual ? Post in the comments!

Digital Temple Thermometer KD-2220 Instruction Manual

Digital Temple Thermometer KD-2220

INSTRUCTION
MANUAL

Digital Temple Thermometer KD-2220

Digital Temple Thermometer
Model KD-2220

IMPORTANT ! Read instruction manual before using thermometer

Contents

Important Things to Know…………………..2
Parts Identification………………………4
Preparation for Use…………………….5
How to Operate the
Thermometer……………………………..6
Memory Mode…………………………….8
Cleaning and Care……………………..10
Troubleshooting and Special Indications……………………………….11
Specifications ………………………….12
Limited Warranty………………………13
FCC Statement…………………………14

Quick Start

  1. Install batteries into the thermometer making sure the polarity is correct.

2. Press and release the POWER button. Unit will beep once. Wait until it beeps again twice and only °F shows in the display.

Do not place the probe to the temple before the2 beeps or while the hour glass is still displayed.

3.Place and hold the thermometer probe firmly to the skin at the temple, wait several seconds for the device to beep once more.

Once you place the probe to the temple, there isno need to press the POWER button again. Doing so will turn the unit off.

4.Read the temperature on the display.

POWER SOURCE
SIZE AAA 1.5V x 2 (included)
WARRANTY:
ONE YEAR FROM THE DATE OF PURCHASE
(excluding batteries)

Important Things to Know

  1. Use the thermometer to measure your temple temperature only, the area be- tween the outer corner of the eye and the hairline, over the temporal artery.
  2. Do not place the thermometer on scarred tissue, open sores or abrasions.
  3. Using drug therapies can raise skin temperature, which may lead to incorrect measurements.
  4. Do not dismantle the unit except to replace the batteries.
  5. Children should not use the ther- mometer without adult supervision.
  6. Do not drop or expose thermometer to electric shock as this may adversely affect its performance.
  7. The thermometer is not waterproof. Do not immerse it in water or liquid of any kind.
  8. To ensure correct readings, wait at least 2 minutes between continuous measurements for the thermometer to return to room temperature.
  9. Do not use the thermometer around flammable materials.
  10. Stop using the thermometer if malfunctions appear or if it operates abnormally.
  11. Clean the thermometer probe after each measurement.
  12. Do not take a measurement if the temple area has just been exposedto direct sunlight, fireplace heat or air conditioner flow, as this may lead to incorrect readings.
  13. If thermometer has been kept or stored in a cold temperature, please wait at least 1 hour for it to return to room temperature before measuring.
  14. Performance of the thermometer may be degraded if the unit is operated or stored outside the stated temperature or humidity ranges, or if the patient’s temperature is below room temp.
  15. Body temperature, like blood pressure, varies from person to person. During the day, it can range from 95.9°F to 100.0°F (35.5 to 37.8°C). For some people there can be a difference be- tween their temple and body temp. We recommend learning what your normal temple temperature is while healthy so you can detect an elevated one when you become ill. For accuracy, be sure to measure the same area of the temple each time.
  16. 16. Avoid taking a measurement for at least 30 minutes after physical exercise, bathing or eating.
  17. Make sure the temporal area is dry and clean of sweat, make-up, etc.
  18. The device is intended for consumer use only.
  19. Calibration is recommended every two years.

Parts Identification

Parts Identification

What are normal temperature values?
Human body temperature varies from person to person. Also, a person’s body temperature can fluctuate throughout the day. Theretofore is very important to know your normal body temperature range. Therefore, were commend you measure your self when healthy to establish referenced temperatures which will make you feel more confident of the measured temperature readings when ill.

Preparation for Use

Preparation for Use

  1. Pull the battery cover off in the direction shown.
  2. 2.Prior to installing new batteries you must clean the metal contact ends of the batteries and the metal springs and contacts for the batteries in the battery compartment.
  3. Install 2 new “AAA” batteries into the battery compartment matching correct polarities.
  4. Replace the battery cover securely
Replace the battery

WARNING:

  1. Do not dispose of batteries in regular household trash, refer to your local disposal laws and manage as hazardous waste.
  2. Do not recharge, put in backwards, disassemble or dispose of batteries in fire. Doing so may result in explosion, leakage and injury.

CAUTION:

  1. Replace both batteries at the same time. Do not mix old and new ones.
  2. Never mix alkaline, standard (carbon- zinc) or rechargeable (nickel-cadmium) batteries.

How to Operate the thermometer

1.Press the button to turn on the unit. A beep sound follows.

turn on

2. The last memory is displayed.

last memory

3. You will hear 2 beeps with the measuring scale shown as Figure 4.

Ready to measure

4. Put the thermometer on the temple. It will beep one time to present measurement completion.

5. The display will light according to the reading. Please refer to table below.

6. If the temperature reading is over 99.5°F(37.5°C), eight consecutive beeps will be heard to indicate fever alarm.

reading

7. Once the measurement is done, you will hear 2 beeps indicating the reading has been recorded and it is ready to take the next measurement. However, we do not recommend consecutive measurements.

Ready for next
measurement

8. Turn off the unit by pressing the POWER button, or the unit will automatically turn off (and beep)after 1 minute of inactivity.

Turn off

Switching between Fahrenheit and Centigrade Scale:
You can switch between °F and °C scales. Within 3 seconds after turning on the device, again press and hold the POWER button. The display will show “CH” with “°F” or “°C”.

Switching between Fahrenheit and Centigrade

Recalling Memories:

  1. Begin with the unit turned off.
  2. Press the POWER button and hold for approximately 3 seconds until the most recent memory is shown, then release.
  3. Press and release the button again and again to scroll through the remaining previous memories.
previous memories

4. When you are finished viewing stored memories, discontinue pressing the button. After a short pause, you will hear 2 beeps indicating the unit is ready to take a new measurement.

Ready to
measure

Deleting Memories:
If you choose to delete memories on the thermometer, this may be done after step 2 or 3 of Recalling Memories.

It is not necessary to delete memories, it is simply an option. Oldest memories will automatically be deleted as you take new measurements. Removing the batteries will also delete all memories from the unit.

~ NOTE ~ ALL memories will be deleted in this process, you cannot delete just one single memory

  1. As you are scrolling through and viewing stored memories, at any time you may press and hold the POWER button for 3 seconds until dEL displays – then release the button.
dEL

2. While dEL is still displayed, press and release* the POWER button once more to finish the delete process. OFF will show on the display and all stored memories are now deleted.

OFF

*If you do not press and release the POWER button in this step, the thermometer will return to recalling memories

Cleaning and Care

Cleaning and Care

Troubleshooting

Troubleshooting

Specifications

Specifications
Specifications

Limited Warranty

This thermometer (batteries excluded) is guaranteed for one year from the date of purchase against manufacturer’s defect under normal use and without evidence of tampering.

WARRANTY EXCLUSIONS:
• Device is not properly operated according to the instructions as described in the manual.
• Device shows any signs of tampering or attempted modification.
• It is at the full discretion of 180 iNNOVATIONSM determine if any visible or notable attempts have been made to tamper, modify, atter or disassemble the device, therefore voiding the warranty.
• Evidence of improper handling or storing, such as dropping. heat, liquid or cleaner damage.
• Natural disasters (such as fire, flood, earthquake, lightening).
• No receipt or proof of purchase showing date of purchase.

Following the instructions closely will ensure years of dependable operator.

If the thermometer is not functioning, first check the batteries. Replace if necessary.

FCC Statement

NOTE: POTENTIAL FOR RADIORELEVISION INTERFERENCE (USA ONLY)

Operation is subject to the following two conditions:
1) This device may not cause harmful Interference, and
2) This device most accept any’ nterference receNed, including interference that may cause undesired operation.

This product has been Meted and found to comply with the limits for a Class B digital device, pursuant to pad 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interferonce in a residential installation. The product generates, uses, and can radiate radio heguency energy and, if not installed and used In accordance with the instructions, may cause harmful interference te radio communications. However, there is no guarantee that Interference will not occur in a particular installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on and off, the user is encouraged to try to correct the intederrence by one or mere of the following measures:

• Reorient or relocate the receiving antenna,
• Increase the separation between the product and the receiver.
• Consult the dealer or an experienced radio/TV technician for help,

Questions about your Manual ? Post in the comments!