SAFETY INSTRUCTIONS

• CARBEST sliding window RW Style Slide is designed exclusively for installation in campervans, motorhomes and caravans.
• Please hire a specialist company to install the window if you do not have sufficient installation knowledge.
• Keep the window closed during rain, snowfall or strong wind.
• Before each trip, check that the window is undamaged and closed.
• If you notice any damage to the window (cracks, damage to the acrylic glass), contact a specialist workshop, your dealer or the manufacturer immediately.

NOTES ON INSTALLATION

• Before mounting, please note the specified wall thickness and compare it with the wall thickness of your vehicle.
• The sliding window is suitable for wall thicknesses from 30 to 45 mm
• Before installation, clarify whether the wall cutout needs to be reinforced.
• Please check and verify the installation location carefully before sawing a cutout in the body of your vehicle. There must be no load-bearing components, power lines or furniture in the way.

ATTENTION: The sliding window can be mounted on the left and right side of the vehicle. When mounting, please note that the movable pane must always be in the front direction of travel.

SCOPE OF DELIVERY

• Sliding window
  
• Mounting frame
  
• Mounting material (screws)
  

ACCESSORIES (OPTIONAL)

Interior frame with mosquito net and blackout

INSTALLATION OF THE SLIDING WINDOW

We always recommend installing the window with at least two people.

1. Make sure that the existing wall cutout on your vehicle matches the specified cutout dimension of the window.
   

   Cutout W x H (mm)	Item number
   500×450	318022
   700×300	318023
   700×400	318024
   900×450	318025
   1000×500	318026

   

2. Thoroughly clean the inside of the outer frame and the entire area around the wall cutout. The surfaces must be clean and free of dust and grease.
3. Please apply sealant evenly and as thick as your thumb to the inside of the outer frame.
   Recommendation: DEKAseal 8936 or SikaLastomer 710
   ATTENTION! Observe the instructions of the sealant manufacturer!
   
4. Center the outer frame in height and width in the wall cutout and carefully press the frame against the vehicle wall so that the sealant can spread evenly.
5. While one person holds and fixes the window frame from the outside, the second person should counter-screw the supplied interior mounting frame with the supplied screws from the inside. Attention: Please do not overtighten the screws!
   
6. Once the window installation is complete, the optional blackout system can be installed if required. Depending on the installation situation and the existing wall thickness, an additional wooden frame may be required for mounting the blackout system. This must be manufactured individually and by the customer. At the four outer corners of the frame are the holes for the screw connection. Fasten the blackout system with the supplied fastening screws and tighten the screws lightly by hand. Check that the mosquito net and the blackout can be moved easily. Close the screw holes with the four cover caps and remove all protective foils.
   
   

WARNING! Heat accumulation between the glass pane and the blackout system may damage the product.
Do not close the blackout system completely when there is strong sunlight and the associated high temperatures.

CLEANING AND CARE INSTRUCTIONS

• Do not use aggressive cleaning agents. These can damage the acrylic glass. Gentle cleaning with water or soapy water is recommended (depending on the degree of soiling of the window).
• Do not use rough cloths, as they can cause scratches and haze. Only use soft, lint-free cloths.

WARRANTY

The warranty period is 36 months. Reimo reserves the right to eliminate possible defects. The warranty is excluded for any damage caused by incorrect use or improper handling.
Limitations of Liability: In no event shall Reimo be liable for incidental, consequential or indirect damages, costs, expenses, loss of use or loss of profits. The stated sales price of the product represents the appropriate amount of Reimo’s limitation of liability.

DISPOSAL

Place the packaging material in the appropriate recycling waste. If you wish to decommission the product permanently, please contact your local recycling center or your specialist dealer for the applicable disposal regulations.

Customer Support

REIMO REISEMOBIL-CENTER GMBH
63329 EGELSBACH · BOSCHRING 10
GERMANY · WWW.REIMO.COM
MADE IN CHINA · © REIMO 03/2023