CADDX FPV Gofilm 20 Universal Solution For Daytime
How to bind ELRS 2.4G
- The flight controller has a built- in ELRS receiver. Use the battery to quickly power up the Gollum 20 three times. When the receiver indicator (as shown in Figure 3) turns red and flashes twice quickly, it enters the binding mode.
- Use the ELRS 2.4G protocol remote controller for frequency binding. Take the Radiomaster ZORRO ELRS 2.4G remote controller settings as an example. Perform the remote controller settings according to Figures (1) (2). After the frequency binding is successful, the flight control ELRS receiver indicator light will be solid red.
Default flrm,uare version: ExpressLRS V3.0.1
ARM & Mode
After the binding is successful, use FC to connect to the Betalight, and enter the Modes tab.
Try to toggle the corresponding switch for each function, You move the Yellow cursor of the corresponding aux channel of the switch, the corresponding function will be turned on when you move to the set range.
Default motor rotation direction
How to bind VTX
- Connect the moonlight kit and the power of the goggles.
- Short press the moonlight kit and goggles linking buttons respectively, when the moonlight kit enters the pairing state The VTX LED turns red, and the goggles end is a DI. .. DI. .. DI. ..
- After the link is successful, the indicator light on the VTX LED turns solid green, the beeping sound on the goggles stops and the screen is displayed.
For more information on how to use the MOONLIGHT KIT, please scan the QR code to view the electronic manual.
Flight control wiring
Pre-flight Check
- Turn on the transmitter and select the correct mode. Please confirm that the arming switch on the transmitter is in the “disarmed” position and the thrott le is all the way down.
- Check whether the propeller steering is correct, whether the rota tion is smooth, and whether the screws are locked.
- Check whether the battery power is sufficient. The 4S battery is fully charged at 16.8V.
- Please confirm the battery is securely attached to the aircraft by the strap. And secure the balance head so that it can’t be struck by the props.
- Observe whether the take- off environment is safe, whether there are obstacles, and whether it is in a no- fly zone.
- Verify that you have clean, strong video in your Fpv goggles or screen. if you see interference or you see another pilot feed, resolve this issue before flying.
CAUTION!
- This product is NOT a toy, thus it is not suited for children under 14 years of age.
Minors should be accompanied by an adult when operating. - Warnings listed in the instructions must be read carefully.
- Improper adjustments and operation will result in crashes and damage to the item.
- Experience is required before handling this product.
Product Information
| GOFILM 20 Features | Equipped with Avata moonlight HD digital VTX, 1080p low-latency long- distance transmission; Support 4k60 video recording; Designed specifically for the Avatar moonlight and can be fitted with ND filters; Use high quality 1303 6000kv motor with strong power; Fixed power plug design reduces exposed wires; Use 2- inch propellers with protective rings for safer flight; Flight controller built-in ELRS 2.4G receiver. |
|
| GOFILM 20 Parameter | Name | GOFILM 20 |
| flight Control | CADX- CADDXF4_AIO_ELRS | |
| VTX | Moonlight Kit | |
| Motor Diagonal | 94mm | |
| Motor | 1303 6000KV | |
| Propeller | HQ Prop T2x2x3 | |
| Weight | 115±5g | |
| Size | 33x123x39mm | |
| Maximum Hover Time | 4S650mAh & About 5 min 30s | |
| Remote Control Receiver | ELRS 2.4G | |
| Battery Interface | XT30 | |
| Flight Control Parameters | MCU | STM32F405RGT6 |
| GYRO and IMU | ICM42688 | |
| Barometer | BMP280 | |
| ExpressLRS Receiver | ELRS V3.0 UART | |
| ESC | 20A 4-IN- 1 | |
| Blackbox | 8MBp | |
| Support Power | 2~4S Lipo/ Lihv | |
| Mounting hole Distance | 25.5×25.5mm | |
| Firmware Target | BET AFLIGHTF4 | |
| VTX Parameters | Model | Moonlight Kit |
| Firmware Name | AvatarMoonlight_Sky_X.X.X | |
| Communication Frequency | 5.725- 5.850 GHz | |
| Transmitter Power (EIRP) | FCC:<30dBm;CE:<14dBm; SRRC: <20dBm; MIC: <25dBm |
|
| 1/0 Interface | JST1 .0*4(power cable); JST0.8*6(USB); microSD Card Slot; IPEX- 1 |
|
| Sensor | Starlight sensor | |
| FOV | Max 160° | |
| Aperture | F2.1 | |
| Shutter | Rolling shutter | |
| ISO | 100- 25600 | |
| Recording Resolution | 4K@30/60fps; 2 7K@30/60fps; 1080p@100/60fps; 720p@60fps |
|
| Max Mbps | 150Mbps | |
| Video Format | MP4 (H.264) | |
| 3D DNA | Support | |
| Gyro flow | Support | |
| Built- in EIS | Support | |
| Wide Power Input | 7.4V- 25.2V | |
| Power Consumption | 12V@1.4A, 8V@2.2A | |
| Memory Card Type | U3 microSD, Max 256G | |
| camera Size | 19.6mmx19mmx24mm | |
| VTX Size | 15.3mmx34.5mmx34.5mm | |
| VTX Installation hole Distance | 20x20mm/ 25x25mm (M2) | |
| Weight | 38.5g (Antenna not included) | |
| OSD | Canvas mode | |
| Latency | Average delay 22ms | |
| Antenna | 2 (IPEX) | |
Customer Support
CADDXFPV Support
email: support@caddxtpv.com
This CMtent is subject to change.
Download the latest version from
https://www.caddxfpv.com
Documents / Resources
 |
CADDX FPV Gofilm 20 Universal Solution For Daytime [pdf] User Guide Gofilm 20 Universal Solution For Daytime, Gofilm 20, Universal Solution For Daytime, Solution For Daytime, For Daytime, Daytime |