DVC DF7, DF7-W 2 Wire Intercom System
Parts i funció
Talk/Monitor
Desplaça't cap avall
Desbloqueja
Silenciar
Desplaça't cap amunt
Desviar
Talk voice volume switch: the volume of the speaker voice when talk with door station, up means high, down means low.
Connexions
AVÍS: the DF7monitor does not support DT-IPG, RLC light mode requires update RLC to support.
DF7 monitors does not support in-out connection.
Muntatge
Configuració de la instal·lació
Configuració de l'adreça
DIP Switcher Set Address
The DIP switches are used to set the user code for each monitor. Total 6 bits can be configured.
- Bit-1 to Bit-5 are used for user code setting. The value range is from 0 to 31, which have 32 different codes for 32 apartments.
- When multi monitors need to be installed in one apartment, these monitors should use the same user code, and the master/slave mode should be set on the monitor. (Details refer to the section of Setting Slave Monitor)
- Bit-6 is bus line terminal switch, which should be set to “ON” if the monitor is at the end of bus line, otherwise be set to “OFF”.
Bit-6 switch setting
Master/Slave setup
By monitor menu Refer address setup step 1
- Toqueu
to get into main menu - In main menu, long press unlock key
- Toqueu
to set monitor master slave
Auto call back
- After 1 and 2 setups, DF7 can apply a calling from DF7, simulator a call from door station.
- When power up and standby (DF7 is screen off), press and hold 3s until parpellejos.
User personalization setup
- Adjust ringtone volume
- levels adjustable. When standby, into main menu, tap fa referència
to switch the volume between large and small.
Change ringtone melody
3 sets of the ring tune selectable. When standby, into main menu, tap (refers 
)to switch the melody between 3 sets, after switch DF7 will play the melody for door station calling, inner call, and ring button separately.
Funcionament
Status setup (Do Not Disturb)
When power up and standby (DF7 is screen off), :
- Toqueu to enable “Do Not Disturb”, the corresponding LED solid on mean the is in Do Not Disturb and will not ring for any calls.
- Toqueu to enable/disable “Divert to APP”. (*Reserve function, requires additional accessary or specific door station to enable, not working for 2easy standard door station.)
Accept calling
When DF7 rings,
- Toqueu to accept calling.
- Toqueu (refers
) to release door lock 1. - Toqueu (refers
) to release door lock2. - Toqueu (refers
) to adjust brightness of the image, 2 levels. - Toqueu (refers
) to switch to other door station camera(if has).
Monitor door station
When power up and standby (DF7 is screen off), or in main menu, tap to start monitoring door station 1.
In monitoring check “Operation, point 2) for operations.
Intercom call / Inner call
When power up and standby (DF7 is screen off), into operate menu, tap referir-se 
to get into intercom/inner call menu.
And use i to scroll to the address needs to call and tap to call, tap again to end calling.
- GU: to Guard Unit.
- INTERIOR: to monitor with the same address.
Operating the light thought DT-RLC/Mini RLC
When power up and standby (DF7 is screen off), into main menu, tap referir-se 
to light up RLC’s light. When the icon turns in yellow means light up
AVÍS: limit support on DT-RLC(with only DT607/608/821,DMR18S)
Restaura la configuració de fàbrica
To restore to the factory default settings, by following steps.
- .Disconnect the DF7 from bus line, wait for 30s, and connect to bus line.
- Within 10s power up, press and hold for 12s, release when and LED flashes.
- A long beep means all setting rest to factory default
Address will remain while the master/slave will restore
Precaucions
- Tots els components s'han de protegir de les vibracions violentes. I no deixar-se impactar, colpejar i caure.
- Please do the cleanness with soft cotton cloth, please do not use the organic impregnant or chemical clean agent. If necessary, please use a little pure water or dilute soap water to clean the dust.
- Es pot produir distorsió de la imatge si el monitor de vídeo està muntat massa a prop del camp magnètic, per exemple, microones, televisor, ordinador, etc.
- Please keep away the monitor from wet, high temperature, dust, caustic and oxidation gas in order to avoid any unpredictable damage.
- Ha d'utilitzar l'adaptador adequat subministrat pel fabricant o aprovat pel fabricant.
- Fixeu-vos en l'alt voltagA l'interior dels productes, consulteu el servei només a un professional format i qualificat.
Especificació
Font d'alimentació: DC20 ~28 V- Consum d'energia : standby 9mA,working 127mA
- Temperatura de treball : -15ºC ~ +55ºC
- Cablejat: 2 cables, no polaritat
- Pantalla del monitor: 7 Inch digital color LCD
- Operation Dimension:
- DF7 : 186.2*139.2*13.8mm(not include the metal support)
El disseny i les especificacions es poden canviar sense previ avís a l'usuari. Es conserven els drets d'interpretació i els drets d'autor d'aquest manual.
Preguntes freqüents
- Q: Can the DF7 monitor be used with standard door stations?
- A: Yes, the DF7 monitor is compatible with standard door stations, but certain functions may require additional accessories or specific door stations for full functionality.
- Q: How many user codes can be set up on the DF7 system?
- A: The system supports up to 32 different user codes for individual apartments or units.
- Q: How to apply auto call back feature on the DF7 system?
- A: After setting up the address and master/slave configurations, initiate a call from the DF7 by pressing and holding a specific button until prompted to release. This simulates a call from the door station.
Documents/Recursos
 |
DVC DF7, DF7-W 2 Wire Intercom System [pdfManual d'usuari DF7, DF7-W, DF7 DF7-W 2 Wire Intercom System, DF7 DF7-W, 2 Wire Intercom System, Intercom System, System |
