bumpboxx Ultra Plus Portable Bluetooth Speaker
FUNCTION DESCRIPTION
BATTERY AND POWER
- The Ultra features a rechargeable lithium-ion battery
- Charge your Ultra+’s battery using ONLY the included 15v 3a AC Adapter.
- The LED indicator light will flash blue when charging and will go solid once the charge cycle is complete.
- Complete charge cycle will take 4-6 hours
- Full battery will last up to 12 hours
- For optimal battery performance, please charge your Ultra+ for 4-6 hours before using it for the first time
BLUETOOTH CONNECTION
- Power on your Ultra+
- Flashing BLUE on screen display means your Ultra is ready to pair to a mobile device. Solid BLUE display means your Ultra+ has established a connection.
- Do a bluetooth scan and select “Ultra+”
- Pair via Bluetooth
- Once connection is established, you can control volume and track using the paired mobile device, the Ultra+’s control panel or the included remote control.
MODE CONTROL - Insert 3.5mm ALIX cable into AUX Input (Unit automatically changes to ALX mode)
- insart Micro SD Card into TF (Unit automatically changes to TF mode)
- frisert USB drive into USB port (Unit automatically changes to TF Player mode)
- TWS Mode Link 2 Bumpboxx Ultra’s together for a True Wireless Steres Experienice
CAREFULLY READ THIS OPERATING MANUAL TO USE AND ENJOY THIS UNIT PROPERLY. KEEP THIS MANUAL FOR FURTHER REFERENCE.
REMOTE CONTROL
- Power
- Mode
- Mute
- Play/Pause
- Channel +/-
- EQ
- Volume +/-
- Repeat
- USB/SD
- 0-9
BEST CARE AND INSTRUCTIONS
- Once you’ve unpackaged the unit and it has finished its charging cycle of roughly 2 full hours, it will allow your unit to function properly.
- It’s perfectly fine to power on the unit during this charging process.
TWS PAIRING INSTRUCTIONS
- Power on both Bumpboxx Ultra+ units. Both of your Bumpboxx Ultra+ display screens will be flashing the word BLUE if unit’s have open bluetooth connections, if not please turn off Bluetooth on all previously paired cell phones within range until you see both unit display’s flashing the words BLUE.
- Hold the TWS (Pause/Play) button on your master unit (the one closest to your device) for 5-10 seconds, you will see the letters BT ST on the display, then you will hear a chime. This means you have successfully established your TWS connection.
(If this is unsuccessful, power down both devices, make sure all previously paired cell phones and devices have tumed off Bluetooth and start again. This time try using the other Bumpboxx Ultra+ as the master.) - Just like you would normally do, find your Bumpboxx Ultra+ on the bluetooth list on your phone and pair to it.
- Crank up the volume and enjoy.
PANEL FUNCTIONS
- Treble
- Bass
- Volume
- USB
- TF Card
- Mode
- Previous/Back
- Play/Pause (TWS Mode)
- Next
- EQ Modes
- AUX In
- AUX Out
- DC 15V Input
- Power On/Off Switch
- LED On/Off Switch
- Charge Status
SPECIFICATIONS
| Drivers | 2-5.25″ |
| Tweeters | 2-2″ |
| Power | 140 W |
| Dual Rear Bass Radiators | |
| AC Adapter | 15V3A |
| Rechargeable Lithium-Ion | |
| Battery Life | 12 Hours |
ACCESSORIES
- AC Adapter x1
- Shoulder Strap x1
- Operation Manual x1
- Remote Control x1
- Microphone x1
- RCA Adapter x1
FCC ID: 2APOI-ULTRA
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and.
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
*RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
CUSTOMER SUPPORT
Documents / Resources
 |
bumpboxx Ultra Plus Portable Bluetooth Speaker [pdf] Instruction Manual Ultra Plus Portable Bluetooth Speaker, Portable Bluetooth Speaker, Bluetooth Speaker, Speaker |