600 Built Under Oven Unit Assembly
TH Note: If fitting a “True Handleless” kitchen, some components will differ to those shown in this instruction and will also be packaged separately. Please refer to your True Handleless guide to Receiving for further details on the different components and difference in installation.
Components
Note: Supports D not used if fitting drawer.
Important Information – True Handleless Kitchens Installers: See Note Above TH

Caution: Some pieces of hardware could be hazardous to small children. Keep all these items out of reach and do not leave children unattended in the assembly area.
Please read these instructions carefully before proceeding. Refer to the Guide to Receiving and Installing your Kitchen booklet for further information.
Note: Due to variation in wall conditions no screws are supplied for fixing the units to the wall. If in doubt consult an expert. Assemble the unit on a clean solid work surface.
In the interest of continuing improvements we reserve the right to amend or adjust the specifications without prior notice. Errors and omissions excepted.
These units may be fitted with a drawer system. The drawers are supplied separately. These instructions show the runner positions for the drawer system.
Follow the instructions supplied with the drawers for drawerbox assembly.
Every effort has been made to ensure that this product leaves the factory in perfect condition. In the unlikely event that an item is damaged or incorrect, please contact the customer services department.
Note – Fitting Handles: (1) Decide where you are going to position each handle to maintain symmetry around your kitchen. (2) Measure the handle centres and mark off each door/drawer position. (3) Drill through the door/drawer using a fine drill (<2.5 mm), then drill back from the rear face using a 4.5 mm drill. (4) Attach with the fixings provided with your handle.
Ref. No. Item Quantity
150101 3.5x12mm 4
150202 4x12mm 14
150201 4x15mm 22
150124 4x25mm 8
154082 10
154085 10
154004 10
154068 6
154047 2
154014 2
154015 2
151999 2
152401 4
152418 4
152402 2
150308 2
150309 2
Tools Required
Drill G-Clamp (pair)
Medium Crosshead Screwdriver Hammer
Large Flathead Screwdriver Tape Measure
Spirit Level Bradawl
1 – 2 Assembly Instructions
TH Modification required at this stage, see True Handleless guide for further details.
1. 2.
154082 10 154004 10
3 Without Drawer
Note: Left hand panel shown only, mirror for right hand panel.
Note: For ease of fitting, Step 17 can be completed at this point.
3.
150124 8
4 With Drawer
Note: Left hand panel shown only, mirror for right hand panel.
Drawer Runner
1 x ‘L’; 1 x ‘R’
x4
x2
Fit as third screw
4.
150202 4 154068 4
5.
5.
154085 10
6 – 7
TH Modification required at this stage, see True Handleless guide for further details.
Do Not Over Tighten
Start Locked
8 – 9
8.
152401 4 150201 16
9.
152418 4
10 – 14 Installation Instructions
10.
150202 4 154047 2
11.
150202 2 154068 2
TH Modification required at this stage, see True Handleless guide for further details.
12.
150308 2 150309 2
13.
150202 4 (Only if Drawer is being fitted)
14.
152402 2 150101 4
15 – 16 Without Drawer
15.
154014 2 150201 2
Note: Do not over tighten screws or use a power screwdriver.
16.
151999 2
17 – 18 Without Drawer
154015 2 150201 4
Note: For ease of fitting, Step 17 can be completed at same time as Step 3
19 – 20 With Drawer
20.
151999 2
Ref. 170805 (05)
Documents / Resources
![]() |
bsi Built Under Oven Unit [pdf] Instruction Manual Built Under Oven Unit, 600, 170805 05 |