FS-BRD-B1-TA9P-MX Tablet Security Enclosure
“
Product Information
Specifications:
- Model: Original Floorstanding
- Sheet Code: BP-IM-047_REV5
- Release Date: 14/05/2025
- Manufacturer: SpotSpot Ltd. (T/A Bouncepad)
Product Usage Instructions:
Assembly Instructions:
- Orientate, locate & secure the Floorstanding Pole to the
Base. - Locate the Cover over the Floorstanding Pole.
- Locate & secure the Case onto the Floorstanding Pole.
Tighten by hand. - Unlock & remove the Faceplate from the Case.
- Feed the Power Cable through the Case & Floorstanding
Pole. - Install the Tablet Setup Kit. Each kit is specific per Tablet
& Case. - Install the Tablet into the Case & connect to Power
Cable. - Locate & lock the Faceplate onto the Case.
- Connect the Power Cable to its mains power source.
- If installing a Battery Pack, connect the Power Cable &
locate into the Base. - With the Cover on the ground, locate & fit the Rubber
Collar. - Installation is now complete.
Branding Mount Assembly Instructions:
- Locate the top Bracket Mount & Mount Bolt to Floorstanding
pole. - Ensure that the Bracket Mount & Mount Bolt are positioned
correctly as shown. - Secure the Bracket Mount & Mount Bolt to the Floorstanding
Pole with the supplied Nuts. Tighten evenly. - Locate the Placard Board to the Bracket Mount. Secure with the
supplied Plastic Screws & Nuts. - Locate & secure the bottom Bracket Mount & Mount Bolt.
Tighten the nuts evenly.
FAQ:
Q: What tools are required for assembly?
A: Socket Driver, 10mm Spanner (or adjustable spanner), T20 Pin
Buttonhead Torx Driver Bit, PZ3 Pozi Driver Bit, 13mm Spanner
Q: How do I ensure all fixings are installed correctly?
A: Follow the orientation and location instructions provided in
the manual for each fixing component. Tighten screws by hand to
avoid damage to your Bouncepad.
Q: What are the approximate maximum Battery Pack
dimensions?
A: 91mm (length) x 56mm (width) x 25mm (height).
“`
Original Floorstanding
Assembly Instructions
Tools Required:
Socket Driver 10mm Spanner *or adjustable spanner
Base
Faceplate Case
Pair of Keys
Floorstanding Pole
Tablet Set-up Kit
1x Case Washer
4x M4 Split Washer
Rubber Collar Fixings Kit
4x M4x16mm 1x T20 Pin Buttonhead Torx Driver Bit
Screw *
4x M6 Split Washer
4x M6x25mm Countersunk
Screw
Sheet Code: BP-IM-047_REV5
Release Date: 14/05/2025
Copyright 2025 SpotSpot Ltd. (T/A Bouncepad) all rights reserved. Confidential, no part of this publication may be reproduced or transmitted in any form without the written permission of the copyright holder.
In the Box
Tighten screw(s) using hand tools, using electric tools may
damage your Bouncepad.
4x M6 Nylon Locking Nut
4x M6 Split Washer
10mm Spanner
4x M6x25mm Countersunk
Screw
PZ3 Pozi Driver Bit
Cover
4x M6 Locking Nut
1x PZ3 Pozi Driver Bit
Fixings List
Due to the modular nature of our product range you may receive additional fixings in the fixings kit. * Previous models may have been supplied with 20mm.
T20 Pin Torx Driver Bit 4x M4x16mm Buttonhead Screw
Case Washer
4x M4 Split Washer
Orientate, locate & secure the Floorstanding Pole
1 to the Base as shown. Ensure that all fixings are installed correctly.
2 Locate the Cover over the Floorstanding Pole.
Locate & secure the Case onto the
3 Floorstanding Pole as shown. Tighten by hand.
4x Tablet Supports
4x Corner Pieces
1x Cable Clip
4 Unlock & remove the Faceplate from the Case.
Feed the Power Cable
5 through the Case & Floorstanding Pole.
Install the Tablet Setup
6 Kit. Each kit is specific per Tablet & Case.
Install the Tablet into the
7 Case & connect to Power Cable.
8 Locate & lock the Faceplate onto the Case.
Approximate maximum Battery Pack dimensions: 91mm (length) x 56mm
(width) x 25mm (Height).
9.1 Connect the Power Cable to its mains power source.
If installing a Battery Pack, connect
9.2 the Power Cable & locate into the Base.
Key number here
*We recommend recording the key number so you can purchase
additional keys in the future.
10 With the Cover on the ground, locate & fit the Rubber Collar.
Use a Kensington® Microsaver product to
11 tether to a secure object. (refer to your Kensington® instructions for full details)
12 Installation is now complete.
Branding Mount
Assembly Instructions
Follow these instructions for the successful assembly of your Branding board to your Floorstanding.
2x Mount Bolt
4x Nuts
2x Mount Bolt Gasket
4x Plastic Screws
Sheet Code: BP-OR-IM-011_REV2
Release Date: 01/04/2019
Copyright 2016 Spotspot Ltd. (T/A Bouncepad) all rights reserved. Confidential, no part of this publication may be reproduced or transmitted in any form without the written permission of the copyright holder.
13mm Spanner
2x Branding Bracket Mount
4x Plastic Nuts
0 Tools required
0 A1 Branding Mount – In the Box
Follow `A’ steps if installing a Placard board
Locate the top Bracket Mount &
A2 Mount Bolt to Floorstanding pole.
Ensure that the Bracket Mount &
A3 Mount Bolt are positioned correctly as shown.
Secure the Bracket Mount & Mount
A4 Bolt to the Floorstanding Pole with the supplied Nuts. Tighten evenly.
Locate the Placard Board to the
A5 Bracket Mount. Secure with the supplied Plastic Screws & Nuts.
Locate & secure the bottom Bracket
A6 Mount & Mount Bolt. Tighten the nuts evenly.
Secure the bottom section of the
A7 Placard Board with the Plastic Screws & Nuts. Installation now complete.
B1 Follow `B’ if installing a Front Board
B2 Locate the top Bracket Mount & Mount Bolt to the Floorstanding pole.
Ensure the Bracket Mount & Mount
B3 Bolt are positioned correctly as shown.
Secure the Bracket Mount & Mount
B4 Bolt to the Floorstanding Pole with the supplied Nuts. Tighten evenly.
Locate the Front Board to the Bracket
B5 Mount. Secure with the supplied Plastic Screws & Nuts.
Locate & secure the bottom Bracket
B6 Mount & Mount Bolt. Tighten the nuts evenly.
Secure the bottom section of the
B7 Front Board with the Plastic Screws & Nuts. Installation now complete.
Documents / Resources
 |
Bouncepad FS-BRD-B1-TA9P-MX Tablet Security Enclosure [pdf] Instruction Manual FS-BRD-B1-TA9P-MX, FS-BRD-W1-TA9P-MX, FS-BRD-B1-TA9P-MX Tablet Security Enclosure, FS-BRD-B1-TA9P-MX, Tablet Security Enclosure, Security Enclosure, Enclosure |