BN-LINK ES1513-5-2 WIRELESS REMOTE CONTROL SOCKET
PRODUCTS VIEW
FEATURES
- Easily controlled by the remote control from up to 100 feet in line-of-sight.
- Separate on and off buttons on the remote
- Outlets will remain powered off after a power outage to save energy.
- Power output up to 1200W at 120V(60Hz).
- Low power consumption, reduces energy use, and extends product life by up to 15%.
- Manual pairing and unpairing.
SETUP
- Install one 12V/23A battery in the remote control’s battery compartment, making sure the polarity of the battery is correct.
- Plug each outlet switch into a socket and plug a device or appliance into each
- Press the on/off buttons for the respective channel on the remote control to operate the outlet switch.
NOTES
- Regularly change the battery in the remote control for the best performance. If you find the outlet switches are not responding or the LED indicator on the remote control becomes dim, the battery should be replaced. Always dispose of old batteries properly with consideration for the environment.
- Make sure the battery and outlets are installed firmly and correctly for safe
- These outlet switches are for indoor use only. Avoid exposure to high-temperature sources, strong sunlight, and moisture. The outlets are best used in the air with good air circulation.
- Do not exceed the maximum load current of 10A(Approximately 1200W).
PROGRAMMING THE OUTLETS
Notes: The outlets are pre-programmed for immediate use, but the configuration can be customized to meet your needs.
To program a remote control transmitter and outlets switch receiver:
- Remove the outlet receiver from the power socket, then plug the outlet receiver back into the power
- Press and hold the “Learning & ON/OFF” button till the indicator start to flash.
- Release the “Learning & ON/OFF” button, and press and hold the corresponding “ON” button on the remote until you hear a “click”.
- The indicator will stop flashing indicating that the pairing is successful.
RESETTING AN OUTLET
Should you wish to unpair an outlet receiver from the remote, or if your outlets are unresponsive to the remote, the outlets can be reset following the below steps.
- Remove the outlet receiver from the power socket.
- Press and hold the “Learning & ON/OFF” button on the outlet receiver.
- While still holding the button, plug the outlet receiver into a power socket and wait to see the indicator flash.
- When the indicator stops flashing, you may release the button, and the reset process is now complete.
- You may program the outlet after.
TROUBLESHOOTING
In the case that one or more of the outlet receivers do not respond to the remote control, please follow the steps given below to resolve the issue:
- Check to see if the battery of the remote is low and needs replacement.
- Make sure that the outlet receiver is correctly placed in the power socket.
- Make sure that the outlet receiver is used in an area with proper air circulation to avoid overheating.
- Reset and program the outlet(s).
TECHNICAL DATA
- Voltage…………………………………. 120V-60Hz
- Max. power…………………………….. 10A 1200W
- Transmission frequency……….. 433.92MHz
- Remote battery……….12V (23A
CENTURY PRODUCTS INC.
- 3545 Granada Ave El Monte Ca 91731 Custom Service Assistance: 1.909.592.1881 E-mail: support@bn-link.com Http://www.bn-link.com
- Hours: 9 AM – 5 PM PST, Mon – Fri Designed in California Made in China
FAQ’s
It won’t at all obstruct your initial set. Trust that your new set will function properly.
I believe what user 97235 was trying to say when he or she mentioned 433 Hz was that it is a frequency. Similar, if not the same frequency is required for communication from the remote control to the device and vice versa.
Yes, the five outlets may be controlled by two remotes, and you can programmer it.
As long as the receiver is placed in a dry location. They perform flawlessly.
These are radio signal controllers rather than IR controllers. This means that in order to utilize the plug, you must either be able to see it or point the remote at it. Within its 100-foot range, they could be in separate rooms or even in a different building.
I don’t see why it shouldn’t work as long as the power consumption of the LED lights is within the range of the remote-controlled switch.
Please check if the battery is installed correctly.
Please replace the battery with a new one.
Please check if there is any obstacle between the remote control and the outlet switch, and make sure there is no obstruction in front of the remote control. If it still doesn’t work, please replace the battery with a new one.
Yes, provided that the ratings of your electric fireplace are not exceeded. 120V, 10A, 1200W
Yes, you can, and the button on the remote that is programmed to that plug will operate anything put into the extension cord.
1 23A-12V alkaline battery it is a tiny battery that is only half the size of a AAA battery.
They are UL rated, yeah.
100 ft.
Any combination of remote controls and switches can be paired together. There are many different pairing possibilities for this device, such as having both remotes control the switches by number or pairing numerous switches to each button on a remote.
