BenQ BL2491T LCD Monitor
Recycle Disassemble Instruction (Dismantled Information)
Requirements according to ANNEX VII of DIRECTIVE 2012/19/EU on waste electrical and electronic equipment (WEEE)
Materials and components with hazardous content LCDs may contain hazardous substances like Pb and BFRs which are covered by exemptions under the RoHS directive. However, the majority is present in the printed circuit boards assembly. In order to reduce emissions as much as possible, a complete disposal of the old appliance is required. This treatment may only be performed in authorized handling plants.
- Product Name: LCD Monitor
- Model No.: GW2491,GW2491E,GW2491T,BL2491,BL2491T
Disassembly Tools
Product exploded view
Table 1 Disassembly parts list
| Item | Description | Item | Description |
| 1 | Deco | 21 | Foot pad |
| 2 | Panel | ||
| 3 | Mylar | ||
| 4 | Screw | ||
| 5 | Screw | ||
| 6 | Rubber lens-cover | ||
| 7 | Lens | ||
| 8 | Key board | ||
| 9 | Power board | ||
| 10 | Main board | ||
| 11 | Main frame | ||
| 12 | Screw | ||
| 13 | Screw | ||
| 14 | Rear cover | ||
| 15 | Screw | ||
| 16 | Hinge | ||
| 17 | Screw | ||
| 18 | Stand | ||
| 19 | Base | ||
| 20 | Screw |
External cable
| External cable | |||
| Item | Description | Qty | Unit |
| P1 | Power cable | 1 | PCS |
| P2 | HDMI cable | 1 | PCS |
Product Disassembly
Place the monitor face down on a smooth surface first. 1. Remove the stand and base.
- Hold the both protruding clips located on the base and squeeze them inward without releasing, at the same Time, use your thumb with the other hand against the base, push it downward until the base detached.
Use the sharp object to press the protruded object, and hold the stand with the other hand to push it downward until the stand detached.
Remove the back cover.
- Release the screws first.
- Use the tool (not provided) starting from the opening to open all the latches of back cover slowly and carefully.
- Disconnect cable to remove back cover.
Remove main frame from the panel.
- Tear out tapes and mylar, then disconnect all the cables.
- Release all the screws.
- Lift up main frame and disconnect cable to remove it.
Take out bezel from panel. 
Separate the board from the main frame.
- Turn over the main frame, remove mylar and release all the screws to separate boards from main frame.
Take out the key board from back cover. （Do not miss the part remarked in yellow）
Recycle characteristics
| Recycle characteristics Part | No. |
| Reuse | – |
| Recycle | 1,3,4,5,6,7,11,12,13,14,15,16,17,18,19,20,21 |
| WEEE annex VII | 2,8,9,10, P1~P2 |
| Recovery | – |
| Disposal | – |
Disassembly Time
- Total time: 30 minutes
FAQ
- Q: Can I recycle the LCD monitor parts at home?
A: No, for proper disposal and recycling of the parts containing hazardous substances, it is recommended to take them to authorized handling plants. - Q: Do I need any additional tools for disassembling the monitor?
A: The necessary disassembly tools are listed in the manual. Make sure to use them as instructed for safe disassembly.
Documents / Resources
 |
BenQ BL2491T LCD Monitor [pdf] Instruction Manual GW2491, GW2491E, GW2491T, BL2491, BL2491T, BL2491T LCD Monitor, LCD Monitor, Monitor |