Bellman BE1521-433 Bridge Transceiver User Manual
BE1521-433 Bridge Transceiver
Troubleshooting
Unpairing your bridge
If you want to use the bridge in another system, you need to unpair it from your current system.
- Hold down both buttons for at least 6s. The top LED will start to blink rapidly in purple.
- Release the buttons and hold down the top button for 3s to confirm. The top and bottom LED lights up.
- Remove the power adapter and batteries to restart.
Installing the app
1. Turn on Bluetooth®
Swipe down from the top of the screen and tap the Bluetooth icon to turn it on.
2. Install the app
Warranty and Safety Information
This booklet guides you on how to use and maintain your Bridge Transceiver. Ensure you read it carefully, including the Safety and Handling section. If you have additional questions, contact your point of purchase for further assistance.
Safety and Handling
Failure to follow these instructions could result in fire, electric shock, or other injury or damage to the device or other property.
- Keep this device out of reach of children under 3 years.
- Note that notifications can be missed if batteries run out.
- This product uses Alkaline batteries as power backup.
Do not expose the batteries to fire or to direct sunlight.
Only use 1.5 V AA alkaline batteries. - This device is designed for indoor use only. Do not expose the device to moisture.
- Protect the device from shocks during storage and transport.
- This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the user guide, may cause harmful interference to radio communication.
- Do not use or store this device near any heat sources such as flames, radiators, ovens or other devices that produce heat.
- Do not dismantle the device; there is a risk of electric shock. Tampering with or dismantling the device will void warranty.
- Protect cables from any potential source of damage.
- Do not make any changes or modifications to this device. Use only power adapters and accessories that are specified in the user guide.
- Batteries are toxic. Do not swallow them! Keep out of reach of children and pets. If they are swallowed, consult your physician immediately!
- Do not expose batteries to fire or to direct sunlight.
- Do not drop your device. Dropping onto a hard surface can damage it.
- Do not install the device in areas where electronic equipment is prohibited.
- The device may only be repaired by an authorized service center.
No company, enterprise or user is allowed to change the frequency, enhance the transmitting power or alter the original characteristics or performance on an approved low power radio frequency device.
Operating Conditions
Operate the device in a dry environment within the temperature and humidity limits stated in this leaflet. If the product gets wet or is exposed to moisture, it should no longer be regarded as reliable and should therefore be replaced.
Cleaning
Disconnect all cables before you clean your device. Use a soft, lint-free cloth. Avoid getting moisture in openings. Do not use household cleaners, aerosol sprays, solvents, alcohol, ammonia, abrasives or compressed air.
Service and Support
If the device appears to be damaged or doesn’t function properly, follow the instructions in the user guide. If the product still doesn’t function as intended, contact an authorized service center for information on service and warranty.
Two-Year Limited Warranty
The company guarantees this product for two (2) years from date of purchase against any defects that are due to faulty materials or workmanship. This guarantee only applies to normal conditions of use and service, and does not include damage resulting from accident, neglect, misuse, unauthorized dismantling, or contamination howsoever caused. This guarantee excludes incidental and consequential damage. Furthermore, the warranty does not cover Acts of God, such as fire, flood, hurricanes and tornadoes.
This warranty gives you specific legal rights and you may also have other rights that vary with territory. Some countries or jurisdictions do not allow the limitation or exclusion of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This guarantee is in addition to your statutory rights as a consumer. The above warranty may not be altered except in writing signed by both parties hereto.
For Australian Consumers: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. BE1521_
You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by the company is under license.
Technical Specifications
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by Bellman & Symfon Group AB could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IC compliance statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Product disposal and recycling information
According to local laws and regulations your product should be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities. The recycling of your product will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.
Battery disposal information
This product contains batteries that according to local laws and regulations must be disposed of separately from household waste. Take used batteries to a collection point designated by the authorities.
FCC Part 68 Compliance
Consumer information: a) This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. b) An applicable certification jacks Universal Service Order Codes (USOC) for the equipment is provided (i.e., RJ11C) in the packaging with each piece of approved terminal equipment. c) A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. d) The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. [For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.] e) If this equipment BE1431 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. f) The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. g) Should you experience trouble with this equipment, please contact Bellman & Symfon North America Inc. (833) BELLMAN or 833-235-5626 for repair or warranty information. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. h) Please follow instructions for repairing if any (e.g. battery replacement section); otherwise do not alternate or repair any parts of device except specified. i) Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. j) NOTICE: If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this bridge does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
FCC ID: 2APAKBE1521
IC: 6693A-BE1521
Distributor | Distribuidor | Distributeur
USA & Canada
Bellman & Symfon North America Inc.
PO Box 1388, Morrisville
North Carolina 27560, USA
Phone: 910-239-5796
Customer support: (833) BELLMAN
or 833-235-5626
Australia & New Zealand
Word of Mouth Technology
PO Box 1001
Croydon VIC 3136
Australia
Phone: 03 9723 0660
Email: info@wom.com.au
Bellman & Symfon Group AB
Södra Långebergsgatan 30
436 32 Askim Sweden
+46 31 68 28 20
Info@bellman.com
bellman.com
Rev: BE1521_080WCD5.0
Date of issue: 2025-02-08
TM & © 2025 Bellman & Symfon AB
All rights reserved
Read More About This Manual & Download PDF:
Documents / Resources
 |
Bellman BE1521-433 Bridge Transceiver [pdf] User Manual BE1521, 2APAKBE1521, BE1521-433 Bridge Transceiver, BE1521-433, Bridge Transceiver, Transceiver |
