ELITE 2000.4 Bluetooth App Processor Amplifier
“
Technical Specifications:
- Dimensions: 236mm x 225mm x 63mm
- Weight: 3.7 kg
- Power Output:
- 4 x 600 WRMS @ 1 ohm
- 4 x 510 WRMS @ 2 ohms
- 2 x 1200 WRMS @ 2 ohms
- 2 x 1200 WRMS @ 4 ohms
- Efficiency: 82%
- Input Voltage: 9 – 15V
- Input Impedance: 100K Ohms
- Total Harmonic Distortion: < 1%
- Input Sensitivity: 150mV – 4V
- Signal-to-Noise Ratio: 85dB
- Frequency Response: 20Hz to 20kHz (-3dB)
- Crossover Frequency: 90Hz – 20kHz @ 12dB/octave
Linkwitz-Riley - Crossover Frequency (Low): 20Hz – 90Hz @ 12dB/octave
Linkwitz-Riley - Fuse Rating: 100A
- Remote Control Fuse Rating: 1.5A
- Current Consumption: 210A (Max), 105A (Musical Signal)
- Wire Gauge: 21mm / 5 AWG
Product Usage Instructions:
Connection Setup:
1. Connect the POWER UNIT GND INPUT to the vehicle chassis for
grounding.
2. Connect the DRIVE INPUT 12VDC (+) for electrical antenna
control.
3. Connect the 12VDC POSITIVE INPUT and GND REM. 12 VDC with an
external fuse.
Front Panel Controls:
1. Use the MONO/STEREO switches for Channel 1 and 2 and Channel
3 and 4 configurations.
2. Adjust gain levels using the Left and Right channel gain
adjustments.
Crossover Settings:
1. Use the CROSSOVER KEY to select between LOW, FLAT, and HIGH
frequencies for crossover adjustment.
Connection Examples:
– For a 1 ohm VERSION BRIDGED setup, use Subwoofer with a coil
@2ohms for 1000Wrms output.
FAQs:
Q: What should I do if the Red LED is flashing?
A: The flashing Red LED indicates output distortion, short
circuit, or thermal protection. Check your connections and speaker
impedance.
Q: How do I adjust the crossover frequency?
A: Use the CROSSOVER KEY to select between LOW (20Hz – 90Hz),
FLAT (20Hz – 20kHz), and HIGH (90Hz – 20kHz) positions for
crossover adjustment.
Q: What is the recommended input voltage range?
A: The amplifier operates within an input voltage range of 9 to
15V.
“`
INSTRUCTION MANUAL
Read before using
TABLE OF CONTENTS
Introduction
3
Description
4
Technical Specifications
8
Solutions to Potential Problems
10
/Bandaaudioparts /banda_audioparts @BandaAudiopartsOficial Visit www.bandaaudioparts.com
INTRODUCTION Congratulations! You have just purchased a product with Banda Audioparts
quality. Developed by qualified engineers and in a high-tech laboratory. To ensure optimal operation, please read this manual carefully before using the product. Keep the manual in a safe and accessible place for future reference.
3
DESCRIPTION
1 4
2 5
3
POWER UNIT 1 GND INPUT
Connect to the vehicle chassis (Ground)
2 DRIVE INPUT 12VDC (+) Connect electrical antenna (Remote)
3 12VDC POSITIVE INPUT
GND REM. 12 VDC
NOTE: USE EXTERNAL FUSE
4 FRONT PANEL
D
G
F
C A
EB
H
I
4
LEDS A Blue (ON): On B Red (CLIPPING): Indicator of
output distortion, short circuit and thermal protection C Yellow: Battery voltage below specified (flashing)
DESCRIPTION
D MONO/STEREO switch (Channel 3 and 4) E MONO/STEREO switch (Channel 1 and 2) F Left channel gain adjustment (Channel
3)/Gain adjustment for MONO (Bridged 2)
G Right channel gain adjustment (Channel 4)
H Right channel gain adjustment (Channel 1)
I Left channel gain adjustment (Channel 2) Gain adjustment for MONO (Bridged 1)
5 SIDE | CROSSOVER KEY
CROSSOVER key
– +/- +
– +/- +
BRIDGED
BRIDGED
– +- –
– +- +
CROSSOVER KEY
Allows you to adjust the Crossover using the selector switch in the LOW (L), FLAT (F) and HIGH (L) positions. This function, when selected in the LOW position, leaves the device only adjustable for a lower frequency (20Hz – 90Hz @ -3dBs).
When positioned in FLAT, the device responds in FULL RANGE (20Hz – 20kHz @ -3dBs). And when positioned at HIGH, it allows adjustment only at high frequencies (90Hz – 20kHz @ -3dBs).
5
DESCRIPTION CROSSOVER SWITCH
6
DESCRIPTION CONNECTION EXAMPLES
– +/- +
– +/- +
1 ohm VERSION CHANNELS 1 and 2 – 2 speakers of 250Wrms @ 2ohms each in parallel resulting in 500Wrms @
1ohm per channel 2 ohms VERSION CHANNELS 1 and 2 – 2 speakers of 250Wrms @ 4ohms each in parallel resulting in 500Wrms @ 2ohms per channel
1 ohm VERSION BRIDGED (CHANNELS 3 and 4) – Subwoofer
1 coil @2ohms 1000Wrms 2 ohms VERSION
BRIDGED (CHANNELS 3 and 4) – Subwoofer 1 coil @4ohms 1000Wrms
7
– +/- +
– +/- +
1 ohm VERSION BRIDGED (CHANNELS 1 and 2) – Subwoofer
1 coil @2ohms 1000Wrms 2 ohms VERSION
BRIDGED (CHANNELS 1 and 2) – Subwoofer 1 coil @4ohms 1000Wrms
TECHNICAL SPECIFICATIONS
1 ohm VERSION BRIDGED (CHANNELS 3 and 4) – Subwoofer
1 coil @2ohms 1000Wrms 2 ohms VERSION
BRIDGED (CHANNELS 3 and 4) – Subwoofer 1 coil @4ohms 1000Wrms
236mm
DIMENSIONS
63mm
3,7 kg
Weight
225mm
8
TECHNICAL SPECIFICATIONS
PARAMETERS
Maximum Power 14.4v @ 1 Ohm Maximum Power 14.4v @ 2 Ohms Maximum Power 14.4v @ 4 Ohm Maximum Power 14.4v Bridged Maximum Power 12.6v @ 1 Ohm Maximum Power 12.6v @ 2 Ohm Maximum Power 12.6v @ 4 Ohm Maximum Power 12.6v Bridged Efficiency @ 8 Ohms Efficiency @ 4 Ohms Efficiency @ 2 Ohms Efficiency @ 1 Ohm Input Voltage Input Impedance THD maximum power Input Sensitivity Signal to Noise Ratio Frequency Response (FLAT Switch) HPF (Crossover) LPF (Crossover) Recommended Fuse Rest Current Maximum Current (sine signal) Maximum Current (musical signal) Power Cables (min. recommended) Output Cables (min. recommended)
1 ohm VERSION
2 ohms VERSION
4 x 600 WRMS
–
4 x 510 WRMS
4 x 600 WRMS
–
4 x 510 WRMS
2 x 1200 WRMS 2 Ohms
2 x 1200 WRMS 4 Ohms
4 x 500 WRMS
–
4 x 400 WRMS
4 x 500 WRMS
–
4 x 400 WRMS
2 x 1000 WRMS 2 Ohms
2 x 1000 WRMS 4 Ohms
–
–
–
82%
78%
78%
71%
–
9 – 15V
100K Ohms
< 1%
150mV – 4V
85dB
20 to 20Khz (-3dB)
90Hz – 20kHz @ 12dB/oitava Linkwitz-Riley
20Hz – 90Hz @ 12dB/oitava Linkwitz-Riley
100A
1,5A
210A
105A
21mm / 5 AWG
2 x 2,5mm / 2 x 14 AWG
9
SOLUTIONS TO POTENTIAL PROBLEMS
PROTECTION SYSTEM
PROBLEM
SOLUTION
Blue & Red LED On Blue LED on and Red flashing with no audio on output Blue LED on and Red LED flashing as per the music Flashing Yellow LED Red LED and Yellow LED on
Amplifier temperature has reached the operating limit.
Install the appliance in a well-ventilated place and ensure that the ventilation system is not obstructed. The amplifier will return to normal operation as soon as the temperature drops.
Short circuit in the audio output or impedance of the speakers below the rated impedance of the amplifier.
Make sure that there is no short circuit in the speaker connection cables and that there is no shorted speaker connected to the system, or that the impedance of the speakers is not less than the minimum impedance of the amplifier.
LED clipping indicating that the distortion in the output is going over 1%.
The system can operate with the amplifier with the Clip LED flashing, but the speakers connected to the output will suffer coil overheating due to Clip distortion.
Amplifier input voltage below 9V.
Check the charge of the batteries where the amplifier is connected. In addition, poor contact in the power cables can also generate voltage drops. Check the voltage at the input of the amplifier and the output of the batteries to verify that the voltage drop is not occurring in the cables or connections.
Problem with the amplifier.
Please refer to our nearest authorized service center.
10
WARRANTY TERMS
Warranty valid for 12 months (one year), starting from the date of purchase, if purchased from an authorized Banda Audioparts dealer. Will be covered by warranty components and/or parts comproved that shows failures in process manufacture or damaged components. Warranty don’t cover: 1. Equipment, parts or components previously altered by unauthorized people. 2. Damages caused by accidents (fall, crash, etc) or natural disasters (overflow, burning, etc). 3. Improper instalation (improper wiring, abuse, installation out of specifications). 4. Shipping costs In case needed any repair, contact the dealer for warranty instructions.
ADDRESS: Banda Audioparts Rua Sofia Atauri Fadin, 256 Neighborhood: Santa Terezinha II Paulínia – SP Brazil Zip Code: 13148-142
NOTE: If out of warranty,repair costs (if needed) will be charged from client. Phone: 55 (19) 3844-7173 e-mail: banda@bandaaudioparts.com.br Banda Audioparts reserved rights to alter caracteristics of the product without previously advice.
WARRANTY REGISTRATION: Name:………………………………………………………………………………………………………………………………………………………………………… Register:…………………………………………………………. Date:……………………………………… Phone:………………………………………….. Address:…………………………………………………………………………………………………………………………………………………………………….. Dealer:………………………………………………………………………………………………………………. Phone:…………………………………………..
11
/Bandaaudioparts /banda_audioparts @BandaAudiopartsOficial Visit www.bandaaudioparts.com
Documents / Resources
 |
BANDA AUDIOPARTS ELITE 2000.4 Bluetooth App Processor Amplifier [pdf] Instruction Manual ELITE 2000.4 Bluetooth App Processor Amplifier, ELITE 2000.4, Bluetooth App Processor Amplifier, App Processor Amplifier, Processor Amplifier |