Banda Audioparts – Automotive Sound Amplifier Modules
Instruction Manual for BANDA AUDIOPARTS models including: ELITE 2000.4 Bluetooth App Processor Amplifier, ELITE 2000.4, Bluetooth App Processor Amplifier, App Processor Amplifier, Processor Amplifier
ELITE 2000.4 – Banda Audioparts
File Info : application/pdf, 12 Pages, 1.50MB
DocumentDocumentINSTRUCTION MANUAL Read before using TABLE OF CONTENTS Introduction 3 Description 4 Technical Specifications 8 Solutions to Potential Problems 10 /Bandaaudioparts /banda_audioparts @BandaAudiopartsOficial Visit www.bandaaudioparts.com INTRODUCTION Congratulations! You have just purchased a product with Banda Audioparts quality. Developed by qualified engineers and in a high-tech laboratory. To ensure optimal operation, please read this manual carefully before using the product. Keep the manual in a safe and accessible place for future reference. 3 DESCRIPTION 1 4 2 5 3 POWER UNIT 1 GND INPUT Connect to the vehicle chassis (Ground) 2 DRIVE INPUT 12VDC (+) Connect electrical antenna (Remote) 3 12VDC POSITIVE INPUT GND REM. 12 VDC NOTE: USE EXTERNAL FUSE 4 FRONT PANEL D G F C A EB H I 4 LEDS A Blue (ON): On B Red (CLIPPING): Indicator of output distortion, short circuit and thermal protection C Yellow: Battery voltage below specified (flashing) DESCRIPTION D MONO/STEREO switch (Channel 3 and 4) E MONO/STEREO switch (Channel 1 and 2) F Left channel gain adjustment (Channel 3)/Gain adjustment for MONO (Bridged 2) G Right channel gain adjustment (Channel 4) H Right channel gain adjustment (Channel 1) I Left channel gain adjustment (Channel 2) Gain adjustment for MONO (Bridged 1) 5 SIDE | CROSSOVER KEY CROSSOVER key - +/- + - +/- + BRIDGED BRIDGED - +- - - +- + CROSSOVER KEY Allows you to adjust the Crossover using the selector switch in the LOW (L), FLAT (F) and HIGH (L) positions. This function, when selected in the LOW position, leaves the device only adjustable for a lower frequency (20Hz - 90Hz @ -3dBs). When positioned in FLAT, the device responds in FULL RANGE (20Hz - 20kHz @ -3dBs). And when positioned at HIGH, it allows adjustment only at high frequencies (90Hz - 20kHz @ -3dBs). 5 DESCRIPTION CROSSOVER SWITCH 6 DESCRIPTION CONNECTION EXAMPLES - +/- + - +/- + 1 ohm VERSION CHANNELS 1 and 2 - 2 speakers of 250Wrms @ 2ohms each in parallel resulting in 500Wrms @ 1ohm per channel 2 ohms VERSION CHANNELS 1 and 2 - 2 speakers of 250Wrms @ 4ohms each in parallel resulting in 500Wrms @ 2ohms per channel 1 ohm VERSION BRIDGED (CHANNELS 3 and 4) - Subwoofer 1 coil @2ohms 1000Wrms 2 ohms VERSION BRIDGED (CHANNELS 3 and 4) - Subwoofer 1 coil @4ohms 1000Wrms 7 - +/- + - +/- + 1 ohm VERSION BRIDGED (CHANNELS 1 and 2) - Subwoofer 1 coil @2ohms 1000Wrms 2 ohms VERSION BRIDGED (CHANNELS 1 and 2) - Subwoofer 1 coil @4ohms 1000Wrms TECHNICAL SPECIFICATIONS 1 ohm VERSION BRIDGED (CHANNELS 3 and 4) - Subwoofer 1 coil @2ohms 1000Wrms 2 ohms VERSION BRIDGED (CHANNELS 3 and 4) - Subwoofer 1 coil @4ohms 1000Wrms 236mm DIMENSIONS 63mm 3,7 kg Weight 225mm 8 TECHNICAL SPECIFICATIONS PARAMETERS Maximum Power 14.4v @ 1 Ohm Maximum Power 14.4v @ 2 Ohms Maximum Power 14.4v @ 4 Ohm Maximum Power 14.4v Bridged Maximum Power 12.6v @ 1 Ohm Maximum Power 12.6v @ 2 Ohm Maximum Power 12.6v @ 4 Ohm Maximum Power 12.6v Bridged Efficiency @ 8 Ohms Efficiency @ 4 Ohms Efficiency @ 2 Ohms Efficiency @ 1 Ohm Input Voltage Input Impedance THD maximum power Input Sensitivity Signal to Noise Ratio Frequency Response (FLAT Switch) HPF (Crossover) LPF (Crossover) Recommended Fuse Rest Current Maximum Current (sine signal) Maximum Current (musical signal) Power Cables (min. recommended) Output Cables (min. recommended) 1 ohm VERSION 2 ohms VERSION 4 x 600 WRMS - 4 x 510 WRMS 4 x 600 WRMS - 4 x 510 WRMS 2 x 1200 WRMS 2 Ohms 2 x 1200 WRMS 4 Ohms 4 x 500 WRMS - 4 x 400 WRMS 4 x 500 WRMS - 4 x 400 WRMS 2 x 1000 WRMS 2 Ohms 2 x 1000 WRMS 4 Ohms - - - 82% 78% 78% 71% - 9 - 15V 100K Ohms < 1% 150mV - 4V 85dB 20 to 20Khz (-3dB) 90Hz - 20kHz @ 12dB/oitava Linkwitz-Riley 20Hz - 90Hz @ 12dB/oitava Linkwitz-Riley 100A 1,5A 210A 105A 21mm / 5 AWG 2 x 2,5mm / 2 x 14 AWG 9 SOLUTIONS TO POTENTIAL PROBLEMS PROTECTION SYSTEM PROBLEM SOLUTION Blue & Red LED On Blue LED on and Red flashing with no audio on output Blue LED on and Red LED flashing as per the music Flashing Yellow LED Red LED and Yellow LED on Amplifier temperature has reached the operating limit. Install the appliance in a well-ventilated place and ensure that the ventilation system is not obstructed. The amplifier will return to normal operation as soon as the temperature drops. Short circuit in the audio output or impedance of the speakers below the rated impedance of the amplifier. Make sure that there is no short circuit in the speaker connection cables and that there is no shorted speaker connected to the system, or that the impedance of the speakers is not less than the minimum impedance of the amplifier. LED clipping indicating that the distortion in the output is going over 1%. The system can operate with the amplifier with the Clip LED flashing, but the speakers connected to the output will suffer coil overheating due to Clip distortion. Amplifier input voltage below 9V. Check the charge of the batteries where the amplifier is connected. In addition, poor contact in the power cables can also generate voltage drops. Check the voltage at the input of the amplifier and the output of the batteries to verify that the voltage drop is not occurring in the cables or connections. Problem with the amplifier. Please refer to our nearest authorized service center. 10 WARRANTY TERMS Warranty valid for 12 months (one year), starting from the date of purchase, if purchased from an authorized Banda Audioparts dealer. Will be covered by warranty components and/or parts comproved that shows failures in process manufacture or damaged components. Warranty don't cover: 1. Equipment, parts or components previously altered by unauthorized people. 2. Damages caused by accidents (fall, crash, etc) or natural disasters (overflow, burning, etc). 3. Improper instalation (improper wiring, abuse, installation out of specifications). 4. Shipping costs In case needed any repair, contact the dealer for warranty instructions. ADDRESS: Banda Audioparts Rua Sofia Atauri Fadin, 256 Neighborhood: Santa Terezinha II Paulínia - SP Brazil Zip Code: 13148-142 NOTE: If out of warranty,repair costs (if needed) will be charged from client. Phone: 55 (19) 3844-7173 e-mail: banda@bandaaudioparts.com.br Banda Audioparts reserved rights to alter caracteristics of the product without previously advice. WARRANTY REGISTRATION: Name:................................................................................................................................................................................................ Register:................................................................... Date:............................................. Phone:.................................................. Address:............................................................................................................................................................................................ Dealer:............................................................................................................................... Phone:.................................................. 11 /Bandaaudioparts /banda_audioparts @BandaAudiopartsOficial Visit www.bandaaudioparts.com