AW-CU484
IEEE 802.15.4 and Bluetooth LE 5.0 wireless microcontroller Stamp LGA Module
User Guide
Rev. A
(For Standard)

The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave.

Revision History.

Version	Revision Date	Description	Initials	Approved
A	2020/10/19	*Initial Version	Jeff Kuo	N.C. Chen

System Setup

(1) Hardware Requirements

• AW-CU484 Module test board
• The host system needs to run the Window10 x64 operating system
• Vector Signal Analyzer/WLAN analyzer for transmitting measurements.
• LLAN signal generator for receiver measurements.
• RF isolation chamber for receiving measurements.
• RF attenuators
• RF cable
• NFC reader

(2) Software Requirements

• PL-2303 GPIO Test (tool)
  
• Tera Term (tool)
  Note: Tera Term is our suggestion, you can try any terminal tool.
  
• DK6Production flash programmer folder (please contact FAE)
  Note: You must have the below files
  
• Mbt.exe (please contact FAE)
  Note: MBT is our suggestion, you can try any hcitool.
  

AW-CU484 EVB

How to download the image

1. You must check the COM number (can check the value by the following picture)
   Note: J9 for DUT COM port
   J10 for PL2303 control Test/Normal mode.
   
2. Find the folder of DK6ProductionFlashProgrammer.
   And type cmd to get into the Dos window.
   
3. Key in
   ZIGBEE IMAGE:
   DK6Programmer.exe -s com6 -p JN-AN-1242-JN518x-Customer-Module-Evaluation-Tool.bin
   BLE IMAGE:
   DK6Programmer.exe -s com6 –p qn9090dk6_hci_black_box_bm.bin
   To open the tool and download the image file (com6 is your DUT J9 Com port )
   
4. Select Y
   
5. Finish
   

How to get into the test mode

1. Open the PL-2303 GPIO Test
2. Setting Com port (J11 com port)
3. Baud rate is 115200
4. Setting the GP1
   Key in 1 and Select the set button. (open test mode)
5. Setting the GP3
   First Key in 0 and Select the set button
   Then Key in 1 and Select the set button again. (Reset)

Test mode(In Zigbee)

1. Open the Tera Term
2. Select setup →Serial port
   • Setting COM port (J9 com port)
   • Baud rate is 115200
3. Select setup →Terminal
   • Receive select LF
   • Transmit select CR+LF
   
4. Select a) standard module
   
5. Select a) Regular
   
6. Customer Module Evaluation Tool (main menu)
   • Select “g” trigger packet test (Rx test)
   • Select “I” transmit packet test (Tx test)
   
7. RX test (Select g)
   g → Start test (start to receive the package)
   +/- → Increment or decrement channel
   X → Return to the main menu
   /→Reset
   
8. TX test (Select i)
   +/- → Can control the channel
   F → Fast transmit rate (fast transmit can help modulation to catch signal)
   X → Return to the main menu
   /→Reset
   
9. NTAG tests(Select n)
   Select Internal or External NTAG
   • Select a) internal NTAG NTAG Tests (Internal)
   • Select a) read contents of EEPROM
   • Select b) write data to EEPROM
   
10. Read contents of EEPROM
    Can read the NFC MAC in Block 0: 04830C3AE26180
    
11. Write data to EEPROM
    Use this test to write data to EEPROM, Format is:
    1:0 1 2 3 4 5 6 7 8 9 A B C D E F
    Programs 0 to F in block 1
    

Test mode(In BLE)

1. Open the folder of MBT
   
2. Open the mbt_setup.ini
   Setting MBT_TRANSPORT=COM3 (your DUT COM port J9)
   DOWNLOAD_BAUDRATE=115200
   APPLICATION_ BAUDRATE=115200
   Enable_Debug_Message=1
   DOWNLOAD_DELAY = 50
   [Solution] Type=2
   
3. And type cmd to get into the Dos window.
   
4. Key in mbt.exe
   
5. Main menu
   If you need more information, please key in mbt help.
   
6. Key in MBT reset
   Make sure the DUT has been reset.
   

Documents / Resources

AzureWave AW-CU484 Wireless Microcontroller Stamp LGA Module [pdf] User Guide AW-CU484 Wireless Microcontroller Stamp LGA Module, AW-CU484, Wireless Microcontroller Stamp LGA Module

References

• User Manual