automatic TECHNOLOGY ATS-1 Sectional Door Openers
Specifications
- Product Name: ATS-1 Sectional Door Opener
- Remote Control Capacity: Up to 64 remotes
- Battery Type: 1 x CR2032
Product Usage Instructions
User Operating Controls
The user operating controls are as follows.
| Button | Function |
|---|---|
| 01 | Close |
| 02 | Close indicator |
Manual Door Operation
- Ensure the door is closed.
- Pull the door towards you until you hear a click.
- Manually operate the door.
CAUTION: Remember to re-engage the opener after closing the door to ensure it is locked.
- Pull the door away from you until you hear a click.
- Press the button to test.
CAUTION: Do not use the string handle to open the door as it may cause injury.
Coding a Remote Control
- Switch on the power.
- Press the specified buttons until the remote LED lights up.
Changing a Battery
- Check the light status table to determine battery status.
- Use a screwdriver to remove screws and open the battery compartment.
Troubleshooting
If you encounter any issues such as the main light flashing, refer to the troubleshooting table in the manual for appropriate remedies.
Frequently Asked Questions
Q: How many remotes can be programmed with the ATS-1 Sectional Door Opener?
A: Up to 64 remotes can be programmed into the opener’s memory.
Q: What type of battery does the ATS-1 Sectional Door Opener use?
A: The opener uses a 1 x CR2032 battery.
Q: What should I do if the main light flashes after the operation?
A: Refer to the troubleshooting table in the manual for specific remedies based on the number of flashes and pauses.
USER OPERATING CONTROLS
| Button | Function |
| 01 | Close |
| 02 | Close indicator |
| 03 | Stop / Set |
| 04 | Open |
| 05 | Open indicator |
| 06 | Mode |
| 07 | Status indicator |
| 08 | Remote status indicator |
| 09 | Adjustment indicator |
MANUAL DOOR OPERATION
TO DISENGAGE THE OPENER
- Tip It is recommended to disengage the door with the door in the closed position.
- Pull towards, it until you hear a click
- Manually operate door
- CAUTION: When the opener is manually disengaged, the door is no longer locked. To lock the door manually, re-engage the opener after the door is closed.
TO ENGAGE THE OPENER
- Pull away, until you hear a click
- Press to test
- CAUTION: Do not use the string handle as a mechanism to open the door. Failure to comply may cause serious injury.
CODING A REMOTE CONTROL
The opener can only be operated from remote controllers that have been programmed into its memory. Up to 64 remotes can be programmed.
STEP ONE
- Switch power on
- STEP TWO
- Press repeatedly till the remote LED lit
- Press repeatedly till the remote LED lit
- STEP THREE
- Opener flashes & beeps
- Release both buttons
- STEP FOUR
- Press to test
- Press to test
REMOTELY CODING A REMOTE CONTROL
Remotely coding works when you have a pre-coded remote control and are in the range of the opener.
- STEP ONE
- Take a pre-coded remote and press the button to duplicate
- Take a pre-coded remote and press the button to duplicate
- STEP TWO
- Use a pen, HOLD for 2 sec the middle button through the coding hole
- Use a pen, HOLD for 2 sec the middle button through the coding hole
- STEP THREE
- Opener flashes & beeps
- Take new remote HOLD for 3-sec RELEASE HOLD for 3-sec RELEASE
- STEP FOUR
- Opener stops flashing & beeping
- Press to test
CHANGING A BATTERY
Battery Type: 1 x CR2032.
STEP ONE
Check Light Status Table
| Light Status | Battery |
| Solid | OK Replace Replace |
| Flashing | |
| No light |
STEP TWO
- Use a screwdriver to remove the scews and open
STEP THREE
- Use a non-metallic object to push out.
- WARNING!: The battery is hazardous and must be kept out of reach of children.
- The battery can cause severe or fatal injuries within 2 hours or less if swallowed or placed inside any part of the body.
- If you suspect the battery has been swallowed or placed inside any part of the body, SEEK IMMEDIATE medical attention.
TROUBLESHOOTING
Main Light = Service / Warning Indicator:
Requirements for a service and user warnings are indicated after operation by the main light repeatable flashing OFF a number of times followed by a pause.
The below table identifies the issues and remedies:
CARING FOR YOUR OPENER
- Preventative servicing of your garage door and opener is important. Your garage door is made up of numerous moving parts designed to lift and lower your door safely and efficiently.
- Ongoing preventative servicing ensures that your door continues to function within factory specifications, greatly reduces the risk of failure and repair bills down the track, and ensures you maintain your Warranty.
- Refer to the installation manual for monthly testing procedures in Section 13 to ensure the garage door is fit for use available HERE
- Online warranty details are available HERE
NEED A SERVICE CALL
- If the opener needs a service please call the dealer who installed the garage door opener (their contact details are usually on a sticker on the back of your garage door).
- For product assistance, general inquiry, or more information, please visit: automatictechnology.com/au or call 1300133944.
Documents / Resources
 |
automatic TECHNOLOGY ATS-1 Sectional Door Openers [pdf] User Guide ATS-1 Sectional Door Openers, ATS-1, Sectional Door Openers, Door Openers, Openers |
