AUTEL TS900 MaxiTPMS Programming Tool User Manual

AUTEL MAXITPMS
APPLIES ONLY TO THE ITS600PRO, TS900, & MS-906PRO2TS

42 TPMS SERVICE FUNCTIONS

	Oil Reset Reset maintenance reminder or service interval indicator
	EPB – Electronic Parking Brake Allows technicians to perform rear brake service on EPB equipped vehicles
	BMS – Battery Management System New battery registration on vehicles equipped with advanced electronic systems
	SAS – Steering Angle Sensor Allows technicians to perform Steering angle sensor & Zero point calibrations after alignment or service
	Immo Keys – Immobilizer & Keys Program new or additional ignition keys (conventional and proximity)
	Brake Bleed Automatic brake bleed feature for ABS control units
	DPF – Diesel Particulate Filter Force regeneration on active and passive diesel particulate filter systems
	Injector Perform fuel injector registration and coding on vehicles with advanced fuel management systems
	Suspension Suspension calibration for vehicles equipped with Air or Hydraulic systems fitted with ride level sensors
	Throttle Electronic Throttle Calibration and idle learn for vehicles equipped with “drive by wire” throttle bodies
	ABS/SRS Zero point calibration of brake pedal; Reset steering angle sensor
	VGT Learn Calculates calibration to increase or decrease exhaust gases driving the turbine wheel
	Relative Compression Disengage fuel system to enable compression test
	Sunroof Initialization Relearns Sunroof power settings after console replacement or loss of battery power
	TEC learn Top Dead Center Offset Learn Procedure is required after Replacement of the PCM, fuel injection pump, crank position sensor or powertrain in many applications
	Window / Door / Roof Component activation and calibration for power door locks, windows and sun roof
	Seats Calibrate occupancy detection systems and seat weigh sensors
	Odometer Allows access to advanced settings in the Instrument Cluster Module such as distance unit
	Language Change Change the language displayed on various control systems including the driver information center
	Headlamp Calibration for adaptive headlight systems
	CHG Tire Size Change speedometer parameters to accommodate different wheel sizes while maintaining accuracy
	Speed & PTO Set a maximum speed limit for vehicle
	Cylinder Technicians can perform Cylinder Contribution test to aid in the diagnostic process (under development)
	Trans Adaption Perform transmission shift adaptation after installing a rebuilt transmission or transmission control module
	Airbag Reset Reset airbag system and indicator on vehicles that do not require SRS Module reprogramming
	Clutch Relearn clutch position after clutch replacement, fluid change, or transmission service
	A/F Setting Serves to adjust the air-fuel ratio of the engine. The optimal ratio was learned by the ECU to ensure smooth operation
	Resolver Sensor Calibration Calibrate Resolver Sensor that controls the drive motor electric vehicle, the power source of an EV
	Automatic Start/Stop Enable the adaptive learning of the Start/Stop system, and serves to activate or deactivate the function
	Electronic Water Pump Start Run water pump for system bleed
	EGR Initialization of the EGR actuator to enable the ECU learning values to return to the initial status
	FRM Reset Serves to reset the parameter settings of the FRM module to the initial status after the FRM module is replaced
	Transport Mode Activated during transportation of the car from the manufacturer to the 4S store. Reduces battery discharge
	HV Battery This function serves to calibrate the battery parameter of high voltage battery, to re-adapt to vehicle control modules
	ACC Sensor will change the original position after it is removed and reinstalled or repaired. It is necessary to perform ACC system calibration
	A/C After removing and repairing the control air flap motor of the A/C system, the position needs to be calibrated
	Rain/Light Sensor This function serves to calibrate the rain/light sensor, making the signal output more accurate
	Reset Control Unit Clears memory of the engine’s previous performance to solve engine issues
	CCS/ACC Reset Adaptive Cruise Control default following distance; Set maximum cruise control speed
	VIN Auto-VIN functionality to identify vehicle year, make and model
	Coolant/Refrigerant Change Performs electronic bleed of coolant system
	HV De-energization/Energization Enable contactors of the battery to open, de-energizing high voltage components on the vehicle and isolating high voltage to the battery/or closest contactors, bringing the system back to an energized state
	All System Auto-Scan Retrieves diagnostic trouble codes and live date from ALL vehicle modules via Auto-Scan. Detailed vehicle scan reports can be printed wirelessly and customized to meet the needs of customers