Auri DC16 Docking Station User Guide

Auri DC16 Docking Station

Product Specifications

• Product Name: AuriTM D4 and D16 Docking Station
• Manufacturer: Ampetronic & Listen Technologies
• Model: AURI-D4, AURI-D16, AURI-DC16
• Country of Origin: United Kingdom & USA

Product Usage Instructions

Setup and Charging:

1. Place the docking station on a flat surface or counter where receivers are easily accessible. Alternatively, mount it to a wall using the provided wall mounting slots (AURI-D4 and AURI-D16).
2. Connect the docking station to a power outlet using the provided power supply.
3. Insert your AuriTM receivers into the charging pockets of the docking station. The receiver’s top LED status will flash while charging and turn solid when fully charged.

General Operation:

Note: The AuriTM Manager software is required for configuration.

1. The software is used to configure broadcast names, encryption keys, and receiver settings stored in the docking station.
2. Default settings: broadcast names and encryption keys are blank, and receiver settings match factory defaults.

LA-382 Intelligent Cable Management Unit:

A cable management unit is available for storing headphones, ear speakers, neck loops, and other accessories (available for AURI-D16 only).

AuriTM Manager Software:

1. Connect the docking station to a PC using a single network cable or connect both to the same existing network.
2. Open AuriTM Manager to view and manage docked receivers.
3. Confirm the docking station is visible in the device list. Direct connection may take approximately 2 minutes after connecting and powering on.

Frequently Asked Questions

• Q: Do I need the AuriTM Manager software for basic operation?
  • A: The software is primarily required for advanced settings and configuration. Basic charging and usage can be done without it.
• Q: Can I use the docking station without connecting it to a PC?
  • A: Yes, you can use the docking station for charging and basic operation without connecting it to a PC. PC connection is mainly for software-based configuration.

Quick Start Guide

PARTS

1. Copy button
2. Copy LED
3. Status LED
4. Status button
5. Power connector
6. Network connector
7. Wall mounting slots
8. LA-382 mounts

Setup and Charging

1. Place the docking station on a flat surface or counter where receivers are easily accessible. Alternatively, the docking station can be mounted to a wall or other surface using the wall mounting slots (AURI-D4 and AURI-D16).
2. Connect the docking station to a power outlet using the provided power supply.
3. Insert your AuriTM receivers into the charging pockets of the docking station. The receiver(s) top LED status will begin flashing to indicate the battery is charging and turn solid when fully charged.

Note: Do not close the docking station case when connected to power! The case must remain open to ensure proper ventilation while charging (AURI-DC16).

General Operation

• Status Button – Press the status button to illuminate the displays of all receivers and show status information.
• Copy Button – A momentary press will copy the library of broadcast names and encryption keys from the docking station to all docked receivers, the red LED flashes slowly during this process. A long press will copy the broadcast names, encryption keys and receiver configuration settings from the docking station to all docked receivers, the red LED flashes quickly during this process. Holding the button for longer than 5s cancels the operation, the red LED will go off to indicate no action will be taken.

Note: The AuriTM Manager software is required to configure the broadcast names, encryption keys, and receiver settings stored in the docking station. By default, the broadcast names and encryption keys will all be blank, and the receiver settings will match the receiver factory defaults.

LA-382 Intelligent Cable Management Unit

A cable management unit is available for conveniently storing headphones, ear speakers, neck loops, and other accessories (available for AURI-D16 only).

AuriTM Manager Software

The AuriTM Manager software application is required to make any settings changes on the docking station and to view and manage docked receivers.

1. Search the Microsoft ® Store for “AuriTM Manager” and install the application.
   https://www.microsoft.com/store/productId/9NRJLR0V9QXH
2. Connect the docking station to the PC using a single network cable or connect them both to the same existing network.
3. Open AuriTM Manager and confirm the docking station is visible in the device list, with a direct connection this could take approximately 2 minutes after connecting and powering on the docking station.
4. Click on the docking station and enter the credentials you would like to use for the device, then enter the default credentials, as shown on the device label.
5. Use the software to update docking station and receiver firmware, adjust receiver settings such as default volume, and manage the library of known broadcast names and encryption keys.

For complete details on care and use, please visit the AuriTM website to download the AuriTM system manual and supporting AuriTM Manager software. www.auriaudio.com

Auri™ D4 and D16 Docking Station Quick Start Guide

• www.auriaudio.com

Auri™ D4 and D16 Docking Station Quick Start Guide

• www.auriaudio.com

AMPETRONIC Unit 2, Trentside Business Village, Farndon Road, Newark NG24 4XB, United Kingdom | Phone: +44.1636.610062 www.ampetronic.com

LISTEN TECHNOLOGIES 14912 Heritage Crest Way, Bluffdale, Utah 84065-4818 USA