ATUMTEK ATSS001 Tripod Selfie Stick
Product Introduction
Product Parameters
| Product model | ATSSOOl |
| Weight | Approx. 157g |
| Remote distance | <10m(33ft) |
| Ambient temperature | -l0″C~S0°C |
| Remote battery capacity | Replaceable 3 Volt Lithium Cell CRl220 38mAH |
| Compatible devices | 105 7.0 and above I Android 5.0 and above |
| Device width | Approx. 2.16-3.42 in |
| Extended length w/o tripod activated | Approx. 7.2-29.3 in |
| Extended length with tripod activated | Approx. 9.6-27.1 in |
| Folded size | Approx. 7.2*1.18 in |
| Remotebutton lifespan | >8,CXXJ times |
How to take out or put back the wireless Bluetooth remote?
Take it out Pull up the top part of ATIJMTEKSelfie stick about 5 cm, then push the Bluetooth remote from bottom to top and take it out from the remote slot. Please refer to picture 1 and 2
Put it back on: Pull out the top part of ATUMTEK selfie stick about 5 cm, then push the Bluetooth remote from top to bottom and place the remote back in the Remote slot as shown. Please refer to picture 1 and2
How to active the Bl uetooth remote battery?
- Taking out the wireless Bluetooth remote, hold it and push the battery cover from bottom to up about 1 mm to loose the battery cover;
- Use your finger to lift the top part of the battery cover, and remove the cover.
- Take out the Lithium cell from battery slot, then remove the plastic insulating strip and put the Lithium cell back.
- Push the battery cover from top to bottom, lock the cover.
How to replace the Lithium Cell battery?
First please refer to the above step 1 &2, then take out the Lithium battery, and put new battery in the slot; Finally lock the battery cover
How to use the selfie stick?
Step 1: Hold the bottom part of ATUMTEK selfie stick, rotate phone bracket upward till 90° to selfie stick. (From back side of the Product.)
Step 2: Horizontally rotate the phone bracket 180″ to the front side of the product, now the phone bracket can be rotated 90° vertically.
Step 3: Hold the bottom part of ATUMTEK selfie stick and use another hand to pull up the stick to your suitable length freely.
Note: Open all three of the tripod legs at the bottom manually to activate the tripod if you want to use the tripod. Put the tripod stand on fiat surface when you use it.
Step4: Pull up the foot cushion on the smartphone holder and widthwise set your phone inside the adjustable sliding bracket on the smartphone holder.
Note: please avoid sticking the buttons of your phone.
How to close?
Step 1: Remove your mobile phone by releasing the adjustable sliding bracket. Then, hold the product middle position and use the otherhand to push the aluminum alloy telescopic arm back from the top.
Note: If you open the tripod, putting back the tripod manually,the magnetic type tripod will close together.
Step 2: Rotate the phone holder 90° vertically, then 180° horizontally, ensure the phone bracket is on the back side of the product. Push down the phone holder near to the stick.
CAUTIONS:
- Please use it in an ambient temperature between 10°C to50°C.
- Please do not continuously rotate the smartphone holder in high frequency.
- Please do not continuously and frequently pull the aluminum alloy telescopic arm up and down.
- Push out on all three of the tripod legs attached to the stem at the button to activate the tripod.
LED light instruction
| No. | Status | LED Indicaot r Ligh t |
|
1 |
Switch On | Green Color On |
| Keep pressing the power & camera 2 in 1 button for 2 seconds, the green light of the wireless Bluetooth remote will be on or flash about 05 seconds. Search’ ATUMTEK’ Bluetooth device on your phone and connect with it. | ||
|
2 |
Switch Off | OFF |
| Long press for 3 seconds, the light of wireless Bluetooth
remote is OFF. |
||
|
3 |
Standby | OFF |
| The wireless Bluetooth remote will standby when in
connections status after 2 minutes. Note: The remote would not switch off in standby status; Press the power & camera 2 in 1 button for once and then the green light will flashes. This means the remote is available le to connect to phone Bluetooth. |
||
|
4 |
Low Power | Green Color Flashing Continuously |
| The green light of the wireless blueooth remote will flash continuously when the power is low, about twice every 3
seconds. |
||
|
5 |
Connected | Green Color On |
| The light of the wireless Bluetooth remote will display green when connected with the device’s Bluetooth. This means it is available to control the built-in camera app on your phone to
take a photo |
||
|
6 |
Connectionless | Green Color Flashing |
| The green light of wireless Bluetooth remote will flash when connected less with the device’s Bluetooth.In this case, please turn the Bluetooth in your phone on and choose to
connect. ATl.JM TEK” |
||
NOTE:
- Open your built-in camera in your phone and press the power & camera 2 in 1 button of once for taking a photo.
- The wireless Bluetooth remote will connect directly after switch on if it is already connected with the phone Bluetooth in last
- The Bluetooth will automatically disconnect when the distance is longer than or equal to 10 met
- Turn the Bluetooth off in your phone and the wireless Bluetooth remote will
- How to disconnect with your phone: Go to your phone Bluetooth setting and disconnect ATUMTEK” ln paired devices.
Contact us via Facebook Messenger (Recommended):
m.me/atumtekproducts
OR
www.atumtek.com
OR
support@atumtek.com
If you find our product satisfactory, please encourage us by sharing your user experience online.
If you need help with this purchase, please do not hesitate to contact us.
Documents / Resources
 |
ATUMTEK ATSS001 Tripod Selfie Stick [pdf] User Manual ATSS001, Tripod Selfie Stick |
