ATOMSTACK R7 Conveyor Feeder

Specifications

• Product Name: R7 Conveyor Feeder
• Compatibility: Specifically designed for the AtomStack Hurricane
• Manufacturer: AtomStack

Product Usage Instructions

Disclaimer
This product is not a toy and is not suitable for individuals under the age of 15. It is a conveyor feeder specifically designed for the AtomStack Hurricane. For the complete User Manual, instructions, and warnings, visit AtomStack’s website. AtomStack reserves the right to update safety guidelines and disclaimers.

Assembly Steps

• Step 1: Align the left/right side panels and the middle panel.
• Step 2: Place the fixing pieces under the panel and assemble in the order shown in the diagram using M4*6 screws.

Used in Combination
The R7 Conveyor Feeder is used in combination with the AtomStack Hurricane for efficient operation. Ensure proper alignment and connection.

Wiring
Refer to the provided wiring instructions for connecting the conveyor feeder to the AtomStack Hurricane. Ensure all connections are secure before operation.

Software Settings
For engraving work with the AtomStack Hurricane using the conveyor feeder, you need to use the LightBurn software. Make sure to download the genuine LightBurn software for optimal performance. Contact customer support at support@atomstack.com for any technical assistance related to software compatibility.

FAQ

• Is the R7 Conveyor Feeder suitable for individuals under 15 years of age?
  
  • No, this product is not a toy and is not suitable for individuals under the age of 15 due to its specific design and functionality.
• What software is recommended for engraving work with the AtomStack Hurricane?
  
  • The genuine LightBurn software is required for engraving work with the AtomStack Hurricane when using the R7 Conveyor Feeder. Make sure to download it for optimal performance.

Disclaimer

• This product is not a toy and is not suitable for individuals under the age of 15.
• This product is a conveyor feeder specifically designed for the AtomStack Hurricane. Please visit [ http://www.atomstack.com/ ]( http://www.atom-stack.com/ ) to access the complete “User Manual” as well as the latest instructions and warnings. AtomStack reserves the right to update this disclaimer and safety operation guidelines.
• Please read this document carefully before using the product to understand your legal rights, responsibilities, and safety instructions; failure to do so may result in property damage, safety accidents, and personal safety hazards.
• By using this product, you are deemed to have understood and accepted all terms and content of this document. Users agree to be responsible for their own actions and all consequences arising from them. Users agree to use the product only for legal purposes and to comply with all terms and content of this document as well as any related policies or guidelines set by AtomStack. You understand and agree that AtomStack will not be liable for any loss caused by the user’s failure to use the product in accordance with this manual, unless you provide the original engraving or cutting files, the configuration parameters of the engraving software used, the operating system information, a video of the engraving or cutting process, and the steps taken before any issue or malfunction occurred.
• AtomStack has the final authority to interpret this document, subject to legal provisions. AtomStack reserves the right to update, modify, or terminate these terms without prior notice.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Declaration of conformity
Hereby, AtomStack Co., Ltd., declares that this product is in compliance with the essential requirements and other relevant provisions of Directive RED 2014/53/EU and the RoHS directive 2011/65/EU & (EU) 2015/863.

 Software Statement

• LightBurn software is required for engraving work with the AtomStack Hurricane. Please download the genuine LightBurn software. AtomStack is not responsible for any losses caused by the operation of third-party software LightBurn.
• AtomStack’s firmware has been thoroughly tested by AtomStack, but there may still be instances of software or hardware incompatibility. If errors occur due to incompatibility, you can contact our customer support for technical assistance at support@atomstack.com .

Parts List

Assembly Steps

• Step 1
  Align the left/right side panels and the middle panel.
• Step 2
  Place the fixing pieces under the panel and assemble in the order shown in the diagram.（44 pcs M4*6）

• Step 3
  Install the assembled panel to base component with 12pcs M5*6 screws.
  Note: The panel must be placed horizontally to expose the four screws in the center of the base.
• Step 4
  If there is any movement between the panel and the base, adjust the position shown in the diagram with an open-end wrench.

Step 5
Instructions for fastening components

1. If you are engraving objects with a width of 340mm-370mm, directly use the fastening components. Slide the parts into the conveyor, and insert the screws in the direction shown in the diagram to install the other fastening components.
2. If the objects being carved are narrower than 340mm, unscrew the knurled screws on the fastening components and replace them with M4*50 knurled screws, and also install the fixing pieces.

Used in combination

The R7 conveyor feeder must be used in combination with the H3 riser.

1. Remove the side plates from riser first.
2. Align conveyor with riser.(Ensure alignment with the guide labels）
3. Assembly of conveyor feeder with riser finished.
4. Push the X-axis of the Hurricane to the top and rotate the Z-axis air nozzle to the highest position.
5. Take out working plate.
6. Pull out the drawer tray
7. Insert the 6 support feet of the AtomStack Hurricane into the 6 holes in the riser to complete the installation.

Please ensure safety during the assembling process.

Wiring

The cable goes through inside of Hurricane under R7, not outside of K60

Software settings

LightBurn Y-axis maximum travel value modification steps

1. Run the LightBurn, get a com port connected, “Ready”displayed at the bar marked by number 2 indicates connection succeed.
2. Go to Machine Settings under Edit menu.
3. Expand output, modify the value of Y Steps per mm($101) to 100 and that of Y max travel(mm)($131) to 800, click Write then OK to save the modification. Note: When the conveyor is not used, please restore Y Steps per mm($101) and Y Max travel($131) to the default values, i.e. 133.33 and 300.
4. Enter ” $drawer_alarm/enable=Off” in command input bar of console and execute it，disable the limit switches of the drawer tray accordingly

Contact us

Customer service:
For detailed warranty policy, please visit our official website: www.atomstack.com
For technical support and service, please email: support@atomstack.com

Manufacturer:
Shenzhen atomstack technologies co., ltd.

Zip code: 518172

Address:
17th Floor, Building 3A, Phase II, Intelligent Park, No. 76, Baohe Avenue, Baolong Street, Longgang District, Shenzhen, Guangdong, China.

Scan QR code:
Scan with QR code reader/barcode scanner or any app with scanner

Documents / Resources

ATOMSTACK R7 Conveyor Feeder [pdf] User Manual R7 Conveyor Feeder, R7, Conveyor Feeder, Feeder

References

• User Manual