OKD 70-inch Mid-Century Modern Fluted TV Stand

Introduction

Thank you for choosing the OKD 70-inch Mid-Century Modern Fluted TV Stand. This manual provides detailed instructions for assembly, operation, maintenance, and troubleshooting to ensure safe and proper use of your new furniture. Please read all instructions carefully before beginning assembly and retain this manual for future reference.

Safety Information

• Two-Person Assembly Recommended: For safety and ease of assembly, it is highly recommended that two adults assemble this TV stand.
• Check All Parts: Before assembly, ensure all parts and hardware are present and undamaged. Do not proceed with assembly if any parts are missing or broken.
• Do Not Overtighten: Tighten all screws and fasteners firmly, but do not overtighten, as this may damage the material.
• Anti-Tip Kit: This TV stand includes an anti-tip kit. It is crucial to install this kit to prevent accidental tipping, especially in households with children or pets. Follow the anti-tip kit instructions carefully.
• Weight Capacity: Do not exceed the maximum weight capacity of the top surface (150 lbs) or the interior shelves (30 lbs per shelf). Overloading can cause structural failure and injury.
• Placement: Place the TV stand on a flat, level surface to ensure stability.

Package Contents

Please verify that all components listed below are present before starting assembly. If any parts are missing or damaged, please contact customer support.

• Main body panels (top, bottom, side panels)
• Back panel
• Adjustable shelves
• Doors with fluted design
• Tapered legs and central support legs
• Hinges and door handles
• All necessary assembly hardware (screws, dowels, cam locks, shelf pins, anti-tip kit)

Assembly Instructions (Setup)

Follow these steps carefully for proper assembly. It is recommended to assemble the unit on a soft, clean surface to prevent scratches.

Step 1: Identify Components and Prepare Area

Unpack all components and lay them out on a clean, soft surface. Refer to the parts list (not provided in detail here, but typically included with physical product) to identify each piece. Ensure you have all required tools (e.g., screwdriver).

Step 2: Assemble the Base and Legs

Attach the tapered legs and any central support legs to the bottom panel of the TV stand using the provided hardware. Ensure they are securely fastened.

Step 3: Construct the Main Frame

Connect the side panels and internal dividers to the bottom panel, then attach the top panel. Use dowels, cam locks, and screws as indicated in the detailed assembly diagrams (refer to your product's specific manual for these diagrams). Ensure all connections are tight and the frame is square.

Step 4: Install Back Panel and Shelves

Slide or fasten the back panel into place. Insert the shelf pins into the desired height holes for the adjustable shelves. Place the adjustable shelves onto the pins. The open central shelf area is designed for media components.

Step 5: Attach Doors and Handles

Mount the hinges to the doors and then attach the doors to the main frame. Install the door handles. The doors feature a soft-close mechanism for quiet operation.

Step 6: Install Anti-Tip Kit

Secure the anti-tip kit to the back of the TV stand and to a wall stud, following the specific instructions provided with the kit. This step is critical for safety.

Assembly Overview Video

Operating Instructions

Adjusting Shelves

The interior shelves are adjustable to accommodate items of various heights. To adjust a shelf, carefully remove any items, lift the shelf, remove the four metal shelf pins, reposition them into the desired holes, and then place the shelf back onto the pins. Ensure all four pins are securely in place before placing items on the shelf.

Soft-Close Doors

The cabinet doors are equipped with soft-close hinges. To close the doors, gently push them shut. The soft-close mechanism will engage, allowing the doors to close quietly and smoothly without slamming.

Cable Management

Utilize the pre-drilled cable access holes in the back panel of the open shelf and cabinet compartments to route and organize your electronic device cables. This helps maintain a tidy appearance and prevents cable clutter.

Maintenance

Cleaning

To clean the TV stand, wipe surfaces with a soft, damp cloth. Avoid using harsh chemicals, abrasive cleaners, or polishes that may damage the finish. Dry immediately with a clean, soft cloth.

Regular Checks

Periodically check all screws and fasteners to ensure they remain tight. Retighten if necessary to maintain the stability and structural integrity of the unit. Ensure the anti-tip kit remains securely fastened to both the stand and the wall.

Troubleshooting

• Wobbly Stand: Ensure the TV stand is placed on a level surface. Check all assembly screws and fasteners and tighten them if loose.
• Misaligned Doors: The hinges are adjustable. Refer to the hinge manufacturer's instructions (usually included with the hardware) for adjusting door alignment. Small adjustments can typically fix gaps or unevenness.
• Missing Parts: If any parts were missing upon delivery, do not attempt to assemble the unit. Contact OKD customer support immediately for replacement parts.
• Damage During Assembly: If a component is damaged during assembly, stop immediately and contact customer support.

Specifications

Warranty and Support

Warranty Information

OKD products are manufactured with quality and care. For specific warranty details regarding your TV stand, please refer to the warranty card included with your purchase or visit the official OKD website. Keep your proof of purchase for any warranty claims.

Customer Support

If you have any questions, require assistance with assembly, or need to report missing/damaged parts, please contact OKD customer support. Contact information can typically be found on the packaging, the official OKD website, or through your retailer.