1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Ant Value VM50 ARGB Mid-Tower Computer Case. Please read this manual thoroughly before beginning assembly to ensure proper setup and to maximize the lifespan of your components.
2. Package Contents
Verify that all components are present in the package:
- Ant Value VM50 Mid-Tower Computer Case
- Pre-installed 4 ARGB Case Fans (3x Front, 1x Rear)
- Accessory kit (screws, standoffs, cable ties)
- User Manual (this document)
3. Setup and Installation
3.1 Preparing the Case
Before installing components, ensure the case is placed on a stable, flat surface. Remove the tempered glass side panel by unscrewing the thumb screws at the rear and carefully sliding it off. The front mesh panel can be removed for easier fan or radiator installation if needed.
Image: The Ant Value VM50 computer case with its tempered glass side panel removed, showcasing internal components and fan setup.
3.2 Motherboard Installation
The VM50 case supports Micro ATX, M-ATX, and ITX motherboards. Install the necessary standoffs for your motherboard form factor. Carefully align your motherboard with the standoffs and I/O shield, then secure it with screws.
Image: Diagram illustrating the supported motherboard sizes (Mini-ITX, Micro-ATX, ATX) within the Ant Value VM50 case.
3.3 Storage Drive Installation
The case provides 1x 3.5" HDD bay and 1x 2.5" SSD bay. Secure your storage drives using the provided screws in the designated mounting locations.
Image: Internal view of the Ant Value VM50 case highlighting the mounting locations for SSD and HDD storage drives.
3.4 Fan and Cooling Installation
The VM50 comes with 4 pre-installed ARGB fans (3x 120mm front, 1x 120mm rear). Additional fan support includes 2x 120mm top fans and 2x 120mm bottom fans. Ensure all fan cables are connected to appropriate headers on your motherboard or fan controller.
Image: Diagram showing the fan mounting locations and sizes supported by the Ant Value VM50 case: 3x 120mm front, 2x 120mm top, 1x 120mm rear, and 2x 120mm bottom.
3.5 I/O Panel Connections
Connect the front I/O panel cables (USB 3.0, USB, HD Audio, Mic, Power, Reset, Power LED, HDD LED) to the corresponding headers on your motherboard. Refer to your motherboard manual for specific header locations.
Image: Close-up view of the Ant Value VM50's front I/O panel, indicating the Power Button, Reset Button, USB 3.0 port, Audio In, Mic In, and additional USB port.
3.6 Cable Management
Utilize the cable routing cutouts and tie-down points behind the motherboard tray to manage cables. This improves airflow and aesthetics.
4. Operating Instructions
4.1 Power On/Off
Press the Power Button located on the front I/O panel to turn on your computer. To turn off, use the operating system's shutdown function or press and hold the Power Button for several seconds.
4.2 ARGB Fan Operation
The pre-installed ARGB fans will illuminate upon system power-on. If your motherboard supports Addressable RGB (ARGB) control, you can synchronize and customize the lighting effects using the motherboard's software. Connect the ARGB cables to the appropriate 3-pin 5V ARGB header on your motherboard.
5. Maintenance
5.1 Cleaning the Case
Regularly clean the exterior of the case with a soft, damp cloth. For the mesh front panel and fan filters, use compressed air or a soft brush to remove dust buildup. Ensure the system is powered off and unplugged before cleaning.
5.2 Internal Dust Removal
Periodically open the side panel and use compressed air to clean dust from internal components, especially heatsinks and fan blades. This helps maintain optimal cooling performance.
6. Troubleshooting
- System not powering on: Ensure all power supply cables are securely connected to the motherboard and components. Verify the front panel power switch cable is correctly connected to the motherboard header.
- Fans not spinning or ARGB not working: Check that all fan power cables and ARGB cables are properly connected. If using motherboard ARGB control, ensure the correct software is installed and configured.
- No display output: Confirm that your graphics card is properly seated in its PCIe slot and that all necessary power cables are connected. Ensure your monitor cable is connected to the graphics card, not the motherboard's integrated graphics port (unless using integrated graphics).
- Overheating: Ensure all case fans are spinning correctly and oriented for optimal airflow. Verify CPU cooler installation and thermal paste application.
7. Specifications
Image: Diagram showing the dimensions of the Ant Value VM50 computer case: 338mm (depth) x 192mm (width) x 447mm (height).
| Feature | Specification |
|---|---|
| Case Type | Mid Tower |
| Dimensions (D x W x H) | 33.8 x 19.2 x 44.7 cm |
| Motherboard Compatibility | Micro ATX, M-ATX, ITX |
| Drive Bays | 1x 3.5" HDD, 1x 2.5" SSD |
| Expansion Slots | 7 |
| Pre-Installed Fans | 3x 120mm Front ARGB, 1x 120mm Rear ARGB |
| Fan Support (Total) | Front: 3x 120mm; Top: 2x 120mm; Rear: 1x 120mm; Bottom: 2x 120mm |
| Liquid Cooling Support (Max) | Rear: 120mm |
| I/O Panel | 1x USB 3.0, 1x USB, 1x HD Audio, 1x Mic, Power & Reset Button, Power & Hard Drive Indicators |
| VGA Card Length (Max) | 290 mm |
| CPU Cooler Height (Max) | 155 mm |
| Material | Acrylonitrile Butadiene Styrene (ABS) |
| Item Weight | 3600 Grams |
8. Warranty Information
The Ant Value VM50 Computer Case comes with a 1-Year Warranty from the date of purchase. This warranty covers manufacturing defects and material faults under normal use. Please retain your proof of purchase for warranty claims. The warranty does not cover damage caused by misuse, accident, modification, or unauthorized repair.
9. Support
For technical assistance, warranty claims, or product inquiries, please contact Ant Value customer support through their official channels. You may also reach out to the importer, Acro Engineering Company, for support related to this product.
- Manufacturer: Ant Esports, Ant Value
- Importer: Acro Engineering Company