1. Introduction
The DATOUBOSS Home Energy Storage All-in-One Machine is an integrated system combining a 48V 11KW hybrid inverter with a 32.15kWh LiFePO4 battery package. This unit is designed for home energy storage, off-grid solar systems, and emergency power supply, offering a convenient and efficient solution without the need for separate inverter and battery purchases or complex wiring.
Figure 1: Overview of the DATOUBOSS All-in-One Energy Storage System.
2. Safety Instructions and Warnings
Please read, understand, and follow all instructions and applicable documentation completely before using or installing this product. Keep all manuals and documentation in a safe place for future reference. Installation must be performed by qualified professionals.
- Use safety equipment and insulated tools.
- Ensure the installation complies with applicable local and national electrical codes.
- Ensure the system is properly grounded.
- Install the battery in a suitable position for the electronic device.
- Keep the battery within a safe temperature range (-10°C to 50°C) for stable operation.
- Use an appropriate cleaner (e.g., dry cloth) to clean the battery. Do not use aerosol cleaners, liquids, sprays, or solvents.
- Ensure all fasteners are properly tightened.
- Do not incinerate, crush, or puncture the battery.
- Do not place the battery in a dangerous or flammable environment where it may come into contact with corrosive chemicals or vapors.
- Do not store or install this product near radiators, heat collectors, kitchens, or enclosures where it may be exposed to sustained overheating.
- Do not immerse this product in liquid.
- Risk of fire, explosion, and burns: If electrical odors or overheating occur, safely disconnect the circuit breaker and call the fire department.
- Keep away from damaged batteries and any leaking liquid (electrolyte) or flammable gas. In case of inhalation, evacuate the area and seek medical attention.
- If battery leakage comes into contact with eyes or skin, rinse the affected area with running water for 15 minutes and seek medical attention.
- WARNING: When installing the product, it is necessary to turn off and disconnect the power.
Figure 2: Safety Instructions and Warnings.
3. Product Components
The DATOUBOSS Home Energy Storage All-in-One Machine integrates a hybrid inverter, MPPT controller, and LiFePO4 battery into a single unit. This design simplifies installation and operation by eliminating the need for separate devices and complex interconnections.
Figure 3: Integrated components of the DATOUBOSS All-in-One Machine.
What's in the Box:
- DATOUBOSS Integrated Home Energy Storage System (48V 628Ah LiFePO4 Battery + 11KW Hybrid Inverter)
- User Manual
4. Installation Guide
Preparation:
- Ensure the equipment is powered off before installation.
- Installation is recommended to be performed by a professional electrician.
Mounting Considerations:
Before choosing a mounting location, consider the following:
- Use safety devices and insulated tools in accordance with applicable local and national electrical codes.
- Do not install the product in harsh environments. Ambient temperature must be between 0°C and 55°C.
- Avoid dangerous, flammable, or corrosive chemicals or vapors.
- Keep away from heat sources like radiators or stoves.
- Ensure no children or pets are present nearby.
- Do not install on flammable building materials. Install vertically on a solid wall.
- Allow sufficient space for heat dissipation and cable removal.
- Install the device at eye level for easy LCD screen readability.
- Ensure proper grounding, braiding, tightening, and wiring.
Tools Required:
- Phillips screwdriver, torque wrench, rivet pliers of appropriate size.
- Appropriate cables and terminals matching the battery pack's safe current and installation dimensions.
Unpacking and Inspection:
- Inspect the equipment before installation. Ensure the packaging is intact.
- Verify that the package contains the integrated home energy storage system and the user manual.
Figure 4: Product Installation Instructions.
5. Operating Instructions
Powering On/Off Sequence:
To turn on the device, first press the battery ON/OFF switch, then the inverter ON/OFF switch.
- Battery ON/OFF: Press the battery ON button. The operation and power indicators will light up.
- Inverter ON/OFF: Press the inverter ON button. The inverter screen will light up.
- PV ON/OFF: Turn on the PV switch and ensure power is on and the PV cable is connected. The product will start PV charging. Turning off the PV switch stops PV input.
- AC Input ON/OFF: Activate the AC input switch and ensure power is connected. The product starts AC charging. Deactivating the AC switch stops AC input.
- AC Output ON/OFF: Activate the AC output switch. The AC output port connects to an external load device, and the product starts charging the external load device. Deactivating the AC switch stops AC output.
Figure 5: Basic ON/OFF Functions.
Touch Screen Interface:
The device features a color touch screen for easy and intuitive operation, allowing users to monitor battery information and switch between multiple pages. This modern interface offers a smoother user experience and longer service life compared to traditional buttons.
Figure 6: Touch Screen Interface.
LCD Display Screens:
The LCD provides detailed information about the system's operation. Navigate through the screens using the touch interface to view:
- Detail Screen: Displays machine type, LCD/inverter/driver/main versions, and various temperature readings (boosting, machine, MPPT, MOS).
- Solar Screen: Shows PV input voltage, current, power, and daily/monthly/yearly/total kWh generated.
- Battery Screen: Provides battery type, BMS communication status, battery voltage, charge/discharge current, and bus voltage.
- BMS Screen: Details BMS 485 protocol, State of Charge (SOC), charge/discharge current, BMS temperature, discharge/charge limit voltage, and charge limit current.
Figure 7: LCD Detail Screen.
Figure 8: LCD Solar Screen.
Figure 9: LCD Battery Screen.
Figure 10: LCD BMS Screen.
6. Maintenance
The integrated LiFePO4 battery features a built-in Battery Management System (BMS) that provides comprehensive protection against overcharge, over-discharge, overcurrent, short circuits, over-temperature, and low-temperature conditions. This significantly reduces maintenance requirements and extends the battery's lifespan.
General Care:
- Regularly inspect the unit for any visible damage or loose connections.
- Keep the unit clean and free from dust. Use a dry cloth for cleaning.
- Ensure adequate ventilation around the unit to prevent overheating.
- Avoid exposing the unit to extreme temperatures or direct sunlight for prolonged periods.
7. Troubleshooting
The touch screen display includes an alert mode to help identify and resolve issues. If error codes or warnings appear, refer to the detailed solutions provided in the full manual. If you are unable to resolve the problem, please contact our professional technical support team.
Common Issues:
- No Power: Check all circuit breakers (AC input, AC output, PV, battery) and ensure they are in the ON position. Verify all cables are securely connected.
- No PV Charging: Ensure PV panels are connected, the PV switch is ON, and there is sufficient sunlight. Check PV input voltage on the LCD.
- No AC Charging: Ensure AC input is connected and the AC input switch is ON.
- No AC Output: Ensure the AC output switch is ON and the load is connected correctly. Check for overload conditions on the LCD.
- Error Codes: Note down any error codes displayed on the LCD and consult the comprehensive manual or contact support.
8. Specifications
Figure 11: Detailed Technical Specifications.
| Feature | Specification |
|---|---|
| Model | JC-1132 |
| Battery Type | LiFePO4 628 Ah |
| Battery Capacity | 32.15 KWh |
| Dimensions (L x W x H) | 580 x 580 x 937 mm |
| Weight | 239 kg |
| Nominal Voltage | 51.2 V |
| Life Cycle @ 25°C | 8000 cycles, 70% (SOH) |
| Life Cycle @ 45°C | 3000 cycles, 70% (SOH) |
| PV Mode | MPPT |
| Max PV Input Power | 2 * 7500 W |
| MPPT Tracking Range | 90-500 VDC |
| Optimal Voltage | 360-430 VDC |
| Max PV Input Voltage | 500 VDC |
| Max PV Input Current | 18 A |
| Max PV Charge Current | 150 A |
| Max AC Charge Current | 150 A |
| Max Charge Current | 150 A |
| Input Form | L+N+PE |
| Nominal Input Voltage | 220/230/240 VAC |
| Voltage Range | 90-280 VAC 3V (Normal Mode), 170-280 VAC 3V (UPS Mode) |
| Frequency Range | 50Hz/60Hz (Adaptive) |
| Nominal Inverter Power | 11000 W |
| Nominal PV Inverter Power | 12000 W |
| Output Voltage | 220/230/240 VAC ±5% |
| Output Frequency | 50/60 Hz ±0.1% |
| Waveform | Pure Sine Wave |
| Peak Power | 22000 VA |
| Overload Capacity | Battery Mode: 11s @ 105-150% load, 2s @ 150-200% load, 400ms @ >200% load |
| LCD Screen | Displays operating measurements, loads, inputs, outputs, etc. |
| Operating Temperature | -10 to 50°C |
| Relative Humidity | 20% to 95% (non-condensing) |
| Storage Temperature | -15 to 60°C |
| Altitude above sea level | Max 1000m. Power derating required above 1000m up to 4000m. |
| Noise Level | <50 dB |
9. Warranty and Support
DATOUBOSS guarantees the quality of its products. This all-in-one machine comes with a 5-year warranty.
Customer Support:
We offer professional 24-hour customer service. If you have any questions about the product, encounter issues, or require assistance, please do not hesitate to contact us through Amazon. Our friendly and patient customer service team is ready to help.
Multi-language Manuals:
While a printed English instruction manual is included in the package, electronic manuals are available in various languages. If you require a manual in a different language, please contact us via Amazon, and we will send it to you as soon as possible.
