Introduction
This manual provides essential instructions for the safe and effective use of your BBLOVE Digital Thermometer, Model AET-F372. Please read this manual thoroughly before using the device and keep it for future reference. This thermometer is designed for accurate temperature measurement in adults and children.
Safety Information
- Do not immerse the entire thermometer in water for extended periods. The device is IP65 water-resistant for cleaning, but not for full submersion.
- Keep out of reach of children. Small parts may pose a choking hazard.
- Do not bite the thermometer probe.
- Avoid dropping or subjecting the thermometer to strong impacts.
- Do not attempt to disassemble or repair the device yourself. Contact customer support if service is required.
- Store the thermometer in a cool, dry place, away from direct sunlight and extreme temperatures.
- Consult a physician if you have concerns about your temperature readings or health.
Product Components
The BBLOVE Digital Thermometer package includes:
- BBLOVE Digital Thermometer (Model AET-F372)
- Magnetic Charging Case
- User Manual (this document)
Figure 1: BBLOVE Digital Thermometer with its magnetic charging case.
Figure 2: The thermometer securely stored within its magnetic charging case.
Setup
1. Initial Charging
Before first use, ensure the thermometer is fully charged. Place the thermometer into its magnetic charging case. The case will provide power to the thermometer. A full charge typically takes a few hours. The LED display on the thermometer will indicate charging status.
2. Powering On/Off
The thermometer powers on automatically when removed from the charging case. To power off, place it back into the charging case. The device also features an automatic shutdown function after a period of inactivity to conserve battery.
Operating Instructions
1. Preparing for Measurement
- Ensure the thermometer probe is clean and disinfected before each use. Refer to the "Maintenance" section for cleaning instructions.
- Remove the thermometer from its charging case. It will automatically power on and display the last measured temperature.
- To reset the temperature data for a new measurement, gently shake the thermometer or place it back into the charging case briefly and then remove it again.
2. Taking a Temperature Reading
The BBLOVE Digital Thermometer is suitable for oral, rectal, and axillary (underarm) temperature measurements. For the most accurate results, it is recommended to continue measuring for 3-5 minutes.
- Oral Use: Place the probe tip under the tongue, as close to the heat pocket as possible. Close your mouth and hold the thermometer in place.
- Rectal Use: Apply a water-soluble lubricant to the probe tip. Gently insert the tip no more than 1/2 inch into the rectum. This method is generally recommended for infants and young children for accuracy.
- Axillary (Underarm) Use: Place the probe tip in the armpit, ensuring good skin contact. Hold the arm firmly against the body. This method is less accurate than oral or rectal measurements.
The thermometer will provide a fast reading. For medical-grade accuracy, continue holding the thermometer in place for 3-5 minutes until the reading stabilizes. A vibration alert will signal when a stable reading is achieved.
Figure 3: Close-up view of the BBLOVE Digital Thermometer, showing the probe and display area.
3. Reading the Display
The large LED display shows the temperature reading.
- "Lo" is displayed when the measured temperature is below 89.6°F (32°C).
- "Hi" is displayed when the measured temperature is above 109.4°F (43°C).
4. Memory Function
Upon powering on, the thermometer automatically displays the last measured temperature. This allows for easy tracking of temperature changes over time.
Maintenance
1. Cleaning and Disinfection
The thermometer is designed with an IP65 water discharge level, making it easy to clean.
- After each use, clean the probe tip with soap and warm water or wipe it with an alcohol swab (70% isopropyl alcohol).
- You can rinse the probe directly under a faucet.
- Important: Do not immerse the entire thermometer in water for a long time. Only the probe area is designed for direct rinsing.
- Allow the thermometer to air dry completely before storing.
2. Storage
Store the thermometer in its magnetic charging case when not in use. This protects the device and keeps it charged. Store in a dry place, away from extreme temperatures and direct sunlight.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Thermometer does not turn on. | Low battery or not properly removed from case. | Place in charging case to charge. Ensure it is fully removed from the case. |
| Inaccurate readings. | Improper placement, insufficient measurement time, or probe not clean. | Ensure proper placement (oral/rectal recommended). Measure for 3-5 minutes. Clean the probe thoroughly. Do not touch the probe with hands during measurement. |
| "Lo" or "Hi" displayed. | Temperature outside measurement range. | "Lo" indicates below 89.6°F (32°C). "Hi" indicates above 109.4°F (43°C). This is normal if the ambient temperature is outside the human body range. If measuring body temperature, re-evaluate placement. |
| Thermometer does not reset. | Not properly reset. | Gently shake the thermometer or place it back into the charging case briefly and then remove it again to reset for a new measurement. |
Specifications
- Model: AET-F372
- Brand: BBLOVE
- Measurement Range: 89.6°F - 109.4°F (32°C - 43°C)
- Accuracy: Medical-grade
- Display: LED
- Water Resistance: IP65
- Weight: Approximately 5 grams (thermometer only)
- Operating Conditions: 5°C-40°C, 15%RH-80%RH, 70kPa-106kPa
- Storage Conditions: -20°C-55°C, 15%RH-93%RH, 70kPa-106kPa
- Manufacturer: Alicn Medical Shenzhen Inc
Warranty and Support
BBLOVE products are manufactured with high-quality standards. For warranty information, technical support, or service inquiries, please refer to the warranty card included with your purchase or visit the official BBLOVE website. Please retain your proof of purchase for warranty claims.
For further assistance, you may contact the manufacturer:
- Manufacturer: Alicn Medical Shenzhen Inc
- Address: Room 4C, Building 1, Zhongzheng Biomedical Industrial Park, No. 21 Linhui Road, Jinsha Community, Kengzi Street, Pingshan District, 518122 Shenzhen, Guangdong, PEOPLE'S REPUBLIC OF CHINA
- Tel: 0086-755-28301548
- Email: info@alicn-med.com
- Website: http://www.alicn-med.com
