1. Introduction
This manual provides detailed instructions for the TELESIN 2-in-1 Magnetic Flash and Beauty Selfie Light. This device integrates both flash fill light and continuous beauty fill light modes, designed to enhance photography and videography in various lighting conditions. It features magnetic attachment for compatible phones, 180-degree angle adjustment, and dual control via physical buttons and Bluetooth.
2. What's in the Box
- Magnetic Selfie Light (1)
- Charging Cable (1)
- Magnetic Alignment Ring (1)
- User Manual (1)
3. Setup
3.1 Attaching the Light
The TELESIN Magnetic Flash and Selfie Light utilizes MagSafe technology for secure attachment to compatible iPhones (iPhone 11 series and newer). Simply align the light with the magnetic area on the back of your phone until it snaps into place.
For non-magnetic phones or devices, use the included magnetic alignment ring. Peel off the adhesive backing from the ring and carefully center it on the back of your phone or phone case. Press firmly to ensure a secure bond. Once the ring is attached, the magnetic light can be easily mounted and removed.
3.2 Charging the Device
Connect the provided Type-C charging cable to the charging port on the light and to a standard USB power source. The device charges in approximately 1 hour. Note that the light does not support operation while charging.
4. Operating Instructions
4.1 Power On/Off and Mode Selection
Press and hold the power button to turn the light on or off. Short press the power button to cycle through the different lighting modes: Flash Fill Light and Beauty Fill Light.
4.2 Adjusting Brightness and Color Temperature (Beauty Fill Light Mode)
In Beauty Fill Light mode, use the dedicated buttons to adjust brightness from 10% to 100%. You can also select from three color temperatures: 2500K (warm), 4500K (neutral), and 6500K (cool) to match your environment or desired effect.
4.3 Using Flash Mode with Bluetooth
To use the flash mode, first ensure the light is in flash mode (indicated by a blue LED). Pair the device with your phone via Bluetooth. The Bluetooth name is typically "TELESIN_LT03". Once paired, pressing the shutter button on the light will simultaneously trigger your phone's camera and activate the flash, providing synchronized illumination for your photos.
4.4 Angle Adjustment
The light features a 180-degree rotatable design, allowing you to adjust the light angle freely. This enables versatile lighting effects, including direct illumination or bouncing light off surfaces for softer results.
Video: Demonstration of the TELESIN Magnetic Selfie Light and Flash Light for Phones, showcasing its features and ease of use.
Video: Overview of the TELESIN 2-in-1 Magnetic Flash & Beauty Selfie Light, highlighting its dual functionality.
5. Maintenance
- Cleaning: Use a soft, dry cloth to clean the surface of the light. Avoid using harsh chemicals or abrasive materials.
- Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
- Charging: Ensure the device is fully charged before extended periods of non-use. Do not operate the light while it is charging.
- Water Resistance: This device is not water resistant. Avoid exposure to water or high humidity.
6. Troubleshooting
6.1 Light Not Turning On
- Ensure the device is charged. Connect it to a power source using the provided Type-C cable.
- Press and hold the power button for a few seconds to ensure it registers.
6.2 Bluetooth Pairing Issues
- Make sure the light is powered on and in flash mode (blue LED).
- On your phone, go to Bluetooth settings and search for "TELESIN_LT03".
- If pairing fails, try turning off and on both the light and your phone's Bluetooth, then attempt to pair again.
- Ensure the light is within the 10-meter Bluetooth range.
6.3 Flash Not Triggering with Phone Camera
- Confirm the light is successfully paired via Bluetooth and is in flash mode.
- The flash is triggered by pressing the physical shutter button on the light, not the on-screen shutter button of your phone.
6.4 Device Gets Warm During Use
It is normal for the device to generate some heat during prolonged use, especially at higher brightness settings. If it becomes excessively hot, turn it off and allow it to cool down.
7. Specifications
| Feature | Detail |
|---|---|
| Model Number | P5-BGD-17-SR |
| Dimensions | 66 × 58.5 × 19 mm (2.6 × 2.3 × 0.7 in) |
| Weight | 60g |
| Power | Flash 15W | Fill Light 3W |
| Illuminance | Flash >5000lux@0.5m | Fill Light >250lux@0.5m |
| Color Temperature | Flash 6500K | Fill Light 2500K/4500K/6500K |
| CRI | >85 |
| Battery | 500mAh 3.7V Type-C |
| Runtime | Fill light only ≥45 min | Flash only ≥1000 times |
| Charge Time | ≤1 hour (no operation while charging) |
| Bluetooth Range | 10m |
| Compatible Devices | iPhone 11 series and newer (MagSafe compatible), other phones with magnetic ring |
| Water Resistance Level | Not Water Resistant |
8. Warranty and Support
8.1 Warranty Information
The TELESIN 2-in-1 Magnetic Flash and Selfie Light comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use. It does not cover damage caused by misuse, accidents, unauthorized modifications, or exposure to water.
8.2 Customer Support
For technical assistance, warranty claims, or any questions regarding your product, please contact TELESIN customer support through the retailer where the product was purchased or visit the official TELESIN website for contact information.
