WINTEMP Instant Hot Water Dispenser User Manual

Introduction

Thank you for choosing the WINTEMP Instant Hot Water Dispenser. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new appliance. This system features a 3.4-quart stainless steel tank, a hot and cold under-sink faucet, precise temperature control from 113-208°F, and WiFi smart control capabilities. Please read this manual thoroughly before use and retain it for future reference.

Safety Information

Always prioritize safety when installing and operating electrical appliances. Ensure the unit is properly grounded. Do not operate the dispenser if the power cord or plug is damaged. Avoid exposing the unit to water or excessive moisture. Keep children away from the hot water faucet to prevent burns. Always unplug the unit before performing any maintenance or cleaning. If any issues arise, consult the troubleshooting section or contact customer support.

Package Contents

Verify that all components are present and undamaged upon unboxing. The package should include:

• 1 x Instant Hot Water Dispenser Unit
• 1 x Hot and Cold Water Faucet
• 1 x Installation Accessory Kit
• 1 x User Manual Book
• 2 x Connector and hose

Product Specifications

Installation

Before beginning installation, ensure your under-sink cabinet meets the following requirements: at least 16 inches of vertical space, and the P-trap or drain pipe positioned above 15 inches from the cabinet floor. Measure carefully, especially if you have a garbage disposal or complex plumbing. An accessory hole with a diameter of 1.10-1.26 inches is required for the faucet. A dedicated electrical outlet and standard water filtration (not included) are also necessary.

Easy 4-Step Installation Overview

1. Step 1: Install Faucet
   Shut off the main water supply. Insert the faucet into the designated sink accessory hole. Secure it from underneath the counter.



2. Step 2: Connect Water Lines
   Connect the water pipes from the faucet to your water filter (if applicable) and then to the dispenser unit. Ensure all connections are secure to prevent leaks.



3. Step 3: Fill Tank with Water
   Turn on the cold water supply. Open the hot water faucet and allow water to flow for approximately 2 minutes to fill the dispenser tank and purge air from the system.



4. Step 4: Plug in and Set Temperature
   Plug the dispenser into a dedicated 110-120V electrical outlet. Use the up/down buttons on the unit or the WiFi app to set your desired water temperature.

Operating Instructions

Temperature Control

The dispenser allows precise temperature adjustment from 113°F to 208°F. Use the up (▲) and down (▼) arrow buttons on the unit's digital display to select your desired temperature. The unit will automatically heat the water to the set temperature.

WiFi Smart Control

For added convenience, the dispenser can be controlled remotely via a dedicated WiFi smart app. This allows you to adjust settings, monitor status, and utilize features like the child safety lock from your smartphone.

Child Safety Lock

The built-in child safety lock feature ensures safe use, especially in households with children. Refer to the app or the full user manual for instructions on how to activate and deactivate this feature.

2-in-1 Hot & Cold Auxiliary Faucet

The dual-function faucet provides both filtered cold water and boiling hot water. Use the appropriate handle to dispense your desired water type. The 360° swivel design offers flexible use for various kitchen tasks.

Maintenance

Regular maintenance ensures optimal performance and longevity of your WINTEMP Instant Hot Water Dispenser. Always unplug the unit and turn off the water supply before maintenance.

• Cleaning the Exterior: Wipe the exterior of the dispenser and faucet with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the finish.
• Descaling: Over time, mineral deposits can accumulate inside the tank, affecting performance. Follow the descaling instructions in the full user manual or consult a qualified technician.
• Filter Replacement: If using an external water filter, replace it according to the manufacturer's recommendations to ensure continued water quality.
• Drainage: For extended periods of non-use or before moving the unit, drain the tank completely. Refer to the full user manual for detailed drainage procedures.

Troubleshooting

If you encounter any issues with your WINTEMP Instant Hot Water Dispenser, refer to the following common troubleshooting tips:

• No Hot Water: Check if the unit is plugged in and powered on. Ensure the water supply valve is open and the tank is filled. Verify the temperature setting is above the current water temperature.
• Water Leaks: Inspect all connections for tightness. Ensure rubber gaskets and O-rings are properly seated. If leaks persist, turn off the water supply and contact customer support.
• Slow Water Flow: Check if the water supply valve is fully open. If using a filter, it might need replacement. Mineral buildup can also restrict flow; consider descaling.
• Error Codes: If an error code appears on the display, consult the full user manual for specific code meanings and solutions.
• WiFi Connectivity Issues: Ensure your home WiFi network is active and the dispenser is within range. Follow the WiFi setup instructions in the manual or app.

Warranty and Support

The WINTEMP Instant Hot Water Dispenser is covered by a 1-year warranty for the entire unit and a 2-year warranty for the inner tank, protecting against manufacturing defects. For warranty claims, technical assistance, or any questions not covered in this manual, please contact WINTEMP customer support. Keep your purchase receipt as proof of purchase.