Introduction
The IMPREMEY Rechargeable Waterproof Shower Lamp is designed to enhance your bathroom experience with dynamic lighting. This lamp features a waterproof design, a rechargeable battery, and offers both ocean wave projection and static mood lighting with multiple color options. It can be controlled via touch or a remote control, making it suitable for various indoor environments, especially bathrooms and bathtubs.
Image: The IMPREMEY Shower Lamp demonstrating its dual-mode functionality, offering both dynamic ocean wave projection and a steady mood light.
Setup
- Unpacking: Carefully remove all components from the packaging. Verify that all items are present: the shower lamp, a remote control (with batteries), and a USB charging cable.
- Initial Charge: Before first use, fully charge the lamp. Connect the provided USB cable to the lamp's charging port and to a standard USB power adapter (not included). The charging indicator light will show the charging status. A full charge typically takes 5-6 hours.
- Placement: Place the lamp on a stable, flat surface within your shower, bathtub area, or any desired bathroom space. Ensure the surface is clean and dry before placement. The lamp's waterproof design allows for safe use in wet environments, but avoid submerging it.
- Remote Control Setup: The remote control comes with pre-installed batteries. If needed, remove any plastic tab to activate the battery. Point the remote directly at the lamp for optimal control.
Image: The IMPREMEY Shower Lamp connected to a USB charger, illustrating its rechargeable nature and approximate dimensions.
Operating Instructions
The IMPREMEY Shower Lamp offers versatile control options for its lighting modes and colors.
Power On/Off
- Touch Control: Press and hold the touch sensor on the lamp base for 2-3 seconds to turn the lamp on or off.
- Remote Control: Press the ON/OFF button on the remote control.
Changing Light Modes and Colors
- Touch Control: Short press the touch sensor to cycle through different static colors and dynamic ocean wave projection modes.
- Remote Control:
- Use the color buttons to select a specific static color (e.g., red, green, blue, white).
- Use the mode buttons (often depicted with wave or light pattern icons) to activate the ocean wave projection effect.
- Adjust brightness using the Brightness Up and Brightness Down buttons.
- Some remotes may include speed control buttons for dynamic modes.
Image: The IMPREMEY Shower Lamp showcasing its range of 16 vibrant colors and dynamic transition effects, controllable via remote.
Official Product Video: IMPREMEY Shower Lamp Overview
Video: An official demonstration of the IMPREMEY Shower Lamp, highlighting its features and operation. This video is provided by the seller, IMPREMEY-USA Direct.
Maintenance
- Cleaning: To clean the lamp, ensure it is turned off and disconnected from any charging cable. Wipe the surface with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Water Exposure: The lamp is designed to be waterproof (IP54 rated) and can withstand splashes and water jets. However, it is not designed for full submersion. Avoid soaking the lamp in water.
- Charging Port: Keep the charging port dry and free from debris. Ensure the waterproof stopper is securely in place when not charging.
- Storage: When not in use for extended periods, store the lamp in a cool, dry place. It is recommended to fully charge the battery every few months to maintain its lifespan.
Image: Diagram illustrating the IP54 waterproof rating, sealed structure, and waterproof stopper of the IMPREMEY Shower Lamp, emphasizing its suitability for wet environments while advising against soaking.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on. | Battery is depleted. | Connect the lamp to a USB power source and charge it fully (5-6 hours). |
| Lamp turns off shortly after being turned on. | Insufficient battery charge or battery degradation. | Ensure the lamp is fully charged. If the issue persists after a full charge, the battery may need service. Contact customer support. |
| Remote control is not working. | Remote battery is dead or remote is out of range. | Replace the remote control battery. Ensure you are pointing the remote directly at the lamp within a reasonable distance. |
| Light projection is dim or unclear. | Lens is dirty or ambient light is too bright. | Clean the projection lens with a soft cloth. Use the lamp in a darker environment for best projection results. |
Specifications
- Brand: IMPREMEY
- Model Number: shower table lamp
- Product Dimensions: 5"D x 5"W x 12.5"H
- Material: Acrylonitrile Butadiene Styrene (ABS)
- Finish Type: Glossy
- Light Source Type: LED
- Power Source: Battery Powered (Rechargeable)
- Battery Life: 6-15 hours (depending on mode/brightness)
- Charging Time: 5-6 hours
- Water Resistance Level: Waterproof (IP54)
- Control Method: Touch, Remote Control
- Room Type: Bathroom
- Included Components: Bulb (integrated)
- UPC: 741654183212
Warranty Information
This IMPREMEY product is covered by a 2-year manufacturer warranty. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. For detailed terms and conditions, or to initiate a warranty claim, please contact IMPREMEY customer support.
Customer Support
For any questions, technical assistance, or support regarding your IMPREMEY Rechargeable Waterproof Shower Lamp, please contact the manufacturer or seller directly.
- Manufacturer: IMPREMEY
- Seller: IMPREMEY-USA Direct
- Refer to your product packaging or purchase documentation for specific contact details.