Xiaomi Truclean W30 Pro Wet Dry Vacuum Instruction Manual

1. Introduction

This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your Xiaomi Truclean W30 Pro Wet Dry Vacuum. Please read this manual thoroughly before first use and retain it for future reference.

2. Important Safety Information

Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, or injury.

• Do not operate the vacuum with a damaged cord or plug.
• Do not use the vacuum to pick up flammable or combustible liquids, or anything that is burning or smoking.
• Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
• Use only as described in this manual. Use only manufacturer's recommended attachments.
• Unplug from outlet when not in use and before servicing.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

3. Product Overview

Familiarize yourself with the components of your Xiaomi Truclean W30 Pro Wet Dry Vacuum.

Figure 1: Main unit of the Xiaomi Truclean W30 Pro Wet Dry Vacuum. This image displays the complete vacuum cleaner, highlighting its sleek white design, handle with control buttons, main body housing the water tanks, and the floor head with the roller brush.

Components:

• Main Vacuum Unit: The primary body of the vacuum.
• Handle: Ergonomic handle with integrated control buttons.
• Clean Water Tank: Holds fresh water for wet cleaning.
• Dirty Water Tank: Collects dirty water and debris.
• Roller Brush: The rotating brush for scrubbing and picking up debris.
• Cleaning Base: For charging and self-cleaning the roller brush.
• Cleaning Brush: For manual cleaning of components.

4. Setup

4.1 Assembly

1. Unpack all components from the packaging.
2. Insert the handle into the main vacuum unit until it clicks securely into place.
3. Ensure the clean water tank and dirty water tank are correctly installed.

4.2 Charging

1. Place the vacuum onto the cleaning base.
2. Connect the power adapter to the cleaning base and plug it into a power outlet.
3. The indicator lights on the handle will show the charging status. Fully charge the vacuum before first use (approximately 4 hours).

5. Operating Instructions

5.1 Filling the Clean Water Tank

• Remove the clean water tank from the main unit.
• Open the tank cap and fill with clean tap water. For enhanced cleaning, a small amount of non-foaming, compatible cleaning solution can be added (refer to solution manufacturer's instructions). Do not overfill.
• Close the cap securely and reinsert the tank into the vacuum.

5.2 Powering On and Selecting Mode

• Press the Power button on the handle to turn on the vacuum.
• The vacuum will typically start in a standard cleaning mode. Use the Mode button (if available) to switch between different cleaning modes (e.g., standard, max, dry-only).

5.3 Cleaning Operation

• Tilt the vacuum back to engage the roller brush and begin cleaning.
• Move the vacuum slowly over the floor surface to allow the roller brush to scrub and the suction to pick up debris and dirty water.
• For stubborn stains, hold the vacuum over the area for a few seconds.
• The 180-degree lie-flat capability allows cleaning under furniture.

5.4 Powering Off

• Press the Power button again to turn off the vacuum.
• Return the vacuum to the cleaning base for charging and self-cleaning.

6. Maintenance

Regular maintenance ensures optimal performance and extends the lifespan of your vacuum.

6.1 Emptying and Cleaning the Dirty Water Tank

• After each use, remove the dirty water tank.
• Carefully open the tank and dispose of the dirty water and debris.
• Rinse the tank thoroughly with clean water.
• Allow the tank to air dry completely before reinserting.

6.2 Self-Cleaning Function

• Place the vacuum on the cleaning base after use.
• Ensure the clean water tank has sufficient water.
• Press the Self-Clean button (if available) or follow the instructions on the display to initiate the self-cleaning cycle. The high-temperature self-cleaning feature will clean and dry the roller brush.
• Empty the dirty water tank after the self-cleaning cycle is complete.

6.3 Cleaning the Roller Brush (Manual)

• If the self-cleaning function is insufficient or for deeper cleaning, remove the roller brush cover and then the roller brush.
• Use the provided cleaning brush to remove any tangled hair or debris from the roller brush.
• Rinse the roller brush under running water.
• Allow the roller brush to air dry completely before reinstallation.

7. Troubleshooting

Refer to this section for common issues and their solutions.

8. Specifications

9. Warranty and Support

For warranty information, please refer to the warranty card included with your product or visit the official XIAOMI website. For technical support or service inquiries, please contact XIAOMI customer service through their official channels.

Keep your purchase receipt as proof of purchase for warranty claims.