ANTEC GSK850 V2 ATX3.1 850W Full Modular PSU User Manual

1. Introduction

Thank you for choosing the Antec GSK850 V2 ATX3.1 850W Full Modular Power Supply Unit. This PSU is designed to provide stable and efficient power to your personal computer, meeting the latest ATX3.1 and PCIe 5.1 standards. It features 80 PLUS Gold certification for high energy efficiency, a PhaseWave Design (LLC + DC-DC) for stable output, and a Zero RPM Manager for quiet operation. The high-quality braided cables ensure durability and a clean build.

Figure 1.1: Antec GSK850 V2 850W Full Modular Power Supply Unit.

2. Safety Information

Please read and understand all safety instructions before installing or operating this power supply unit. Failure to do so may result in personal injury or damage to the product and other components.

• Electrical Hazard: Do not open the PSU casing. High voltages are present inside, even when the unit is unplugged. There are no user-serviceable parts inside.
• Ventilation: Ensure adequate airflow around the PSU. Do not block ventilation openings.
• Environment: Operate the PSU in a dry, well-ventilated environment. Avoid extreme temperatures, humidity, and dust.
• Power Source: Connect the PSU only to a grounded power outlet with the correct voltage and frequency as specified on the unit's label.
• Cables: Use only the modular cables provided with the PSU. Using third-party cables may cause damage.
• Installation: Ensure all cables are securely connected before powering on the system.
• CircuitShield Protection: This PSU includes comprehensive industrial-grade protection (OCP, OVP, UVP, SCP, OPP, OTP, SIP, NLO) to safeguard your system. However, these protections are not a substitute for proper installation and handling.

3. Package Contents

Verify that all items listed below are present in your package. If any items are missing or damaged, please contact your retailer or Antec support.

• Antec GSK850 V2 850W Full Modular Power Supply Unit
• Modular Cable Set (including 12V-2x6 GPU cable for PCIe 5.1)
• AC Power Cord
• Mounting Screws
• User Manual (this document)

4. Setup and Installation

Follow these steps to properly install your Antec GSK850 V2 PSU into your computer system.

4.1. Preparation

1. Ensure your computer is completely powered off and unplugged from the wall outlet.
2. Open your computer case to access the PSU mounting area.
3. If replacing an existing PSU, carefully disconnect all cables from the old unit and remove it.

4.2. PSU Installation

1. Position the Antec GSK850 V2 PSU into the designated PSU bay in your computer case. Ensure the fan is oriented correctly for optimal airflow (typically facing downwards if there's a bottom vent, or upwards if not).
2. Secure the PSU to the case using the provided mounting screws.
3. Due to its compact size, this PSU is designed to fit a wide range of computer cases.
   

   Figure 4.1: Compact size for broad compatibility and full modular cable management.

4.3. Cable Connection

The GSK850 V2 is a full modular PSU, allowing you to connect only the cables necessary for your system, which improves airflow and cable management.

1. Connect the required modular cables to the corresponding ports on the PSU. Refer to the diagram below for cable types and connectors.
2. Connect the other end of each cable to the appropriate component (motherboard, CPU, GPU, SATA devices, etc.).
3. Ensure the 12V-2x6 GPU cable is used for PCIe 5.1 compatible graphics cards. This PSU is ATX3.1 and PCIe 5.1 compatible.
   

   Figure 4.2: ATX 3.1 and PCIe 5.1 compatibility with dedicated 12V-2x6 GPU cable.

4. The high-quality braided cables offer enhanced durability and a cleaner aesthetic.
   

   Figure 4.3: Illustration of the high-quality braided cables.

5. Refer to the table and image below for a detailed overview of the included cables and connectors:
   

   Figure 4.4: Detailed view of included cables and connectors.

   Table 4.1: Cable and Connector Specifications

   Quantity	Cable Type	Cable Length	Connectors Per Cable
   1	24(20+4)pin M/B	500mm	1
   1	16(12+4)pin PCIe 5.1 12V-2x6 (600W)	500mm	1
   2	8(4+4)pin CPU	750mm	1
   2	8(6+2)pin PCI-E	600mm + 150mm	2
   2	SATA	450mm + 150mm + 150mm + 150mm	4
   1	Molex	450mm + 150mm + 150mm + 150mm	4

6. Organize cables neatly within your case for optimal airflow and aesthetics.

4.4. Final Steps

1. Close your computer case.
2. Connect the AC power cord to the PSU and then to a grounded wall outlet.
3. Flip the power switch on the PSU to the "ON" position.
4. Power on your computer.

5. Operating Instructions

The Antec GSK850 V2 PSU is designed for efficient and quiet operation.

5.1. Zero RPM Manager

This PSU features a Zero RPM fan mode. In this mode, the 120mm silent fan remains off under low to moderate loads, ensuring silent operation. The thermal sensors activate the fan only when necessary, typically under higher power loads, to maintain optimal cooling and extend the PSU's lifespan.

Figure 5.1: Zero RPM Manager fan curve and 120mm silent fan illustration.

5.2. Power On/Off

• To power on your system, ensure the PSU's main power switch is in the "ON" position, then press your computer's power button.
• To power off your system, shut down your operating system normally. For complete power disconnection, flip the PSU's main power switch to the "OFF" position and unplug the AC power cord.

6. Maintenance

Proper maintenance can extend the lifespan of your PSU and ensure optimal performance.

• Cleaning: Periodically clean the exterior of the PSU and the fan intake/exhaust vents using compressed air to remove dust buildup. Ensure the PSU is powered off and unplugged before cleaning.
• Cable Management: Regularly check that all modular cables are securely connected and not obstructing airflow within the case.
• Environment: Maintain a clean, dry, and well-ventilated environment for your computer system.

7. Troubleshooting

If you encounter issues with your Antec GSK850 V2 PSU, refer to the following common troubleshooting steps.

7.1. No Power / System Not Turning On

• Check Power Connections: Ensure the AC power cord is securely plugged into both the PSU and the wall outlet. Verify the PSU's main power switch is in the "ON" position.
• Internal Connections: Confirm that the 24-pin motherboard cable, 8-pin CPU cable, and all other necessary modular cables are firmly connected to both the PSU and the respective components.
• Wall Outlet: Test the wall outlet with another device to ensure it is providing power.
• Power Button/Front Panel: Ensure your case's front panel connectors (especially the power switch) are correctly connected to the motherboard.

7.2. System Instability / Random Shutdowns

• Overload: Ensure your system's power requirements do not exceed the PSU's 850W capacity.
• Overheating: Check for proper ventilation within your PC case. Ensure the PSU fan is not obstructed and is operating when under load.
• Loose Connections: Re-seat all power cables to ensure they are making proper contact.
• Component Issues: Instability can also be caused by other components (RAM, GPU, CPU). If the PSU seems fine, test other components.

7.3. Fan Noise

• Zero RPM Mode: The fan may not spin under low loads. This is normal operation for the Zero RPM Manager.
• Dust Buildup: Clean the fan and vents as described in the Maintenance section.
• Obstruction: Ensure no cables or foreign objects are interfering with the fan blades.

If these steps do not resolve your issue, please contact Antec customer support.

8. Specifications

Detailed technical specifications for the Antec GSK850 V2 PSU.

9. Warranty and Support

Antec stands behind the quality of its products.

9.1. Warranty Information

The Antec GSK850 V2 PSU comes with a 10-Year Warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. For full warranty terms and conditions, please visit the official Antec website.

9.2. Customer Support

If you require technical assistance, have questions about your product, or need to initiate a warranty claim, please contact Antec customer support through their official channels.

You can find more information and support resources by visiting the Antec Store: Antec Official Store