Introduction
This manual provides essential information for the correct installation, operation, and maintenance of your tectake i-Size Car Seat. Please read these instructions carefully before using the product to ensure the safety and comfort of your child. This car seat is designed for children from 40 cm to 150 cm in height, with a maximum weight of 36 kg, and complies with ECE R129 i-Size safety standards.
Safety Information
Your child's safety is paramount. Always adhere to the following safety guidelines:
- i-Size Certification (ECE R129): This car seat meets the latest European safety standards, providing enhanced protection, especially against side impacts.
- ISOFIX and Top Tether: Always use the ISOFIX connectors and the Top Tether strap for a secure and stable installation in your vehicle. Ensure both are correctly engaged.
- 5-Point Safety Harness: For children within the appropriate height range, always secure your child using the integrated 5-point harness. Ensure it is snug and correctly adjusted.
- Vehicle Compatibility: Only install this car seat in vehicles equipped with ISOFIX anchor points and a Top Tether attachment point. Consult your vehicle's owner manual.
- Child Height and Weight Limits: This seat is suitable for children from 40 cm to 150 cm in height and up to 36 kg. Do not use the 5-point harness beyond the specified height/weight limits (refer to operating instructions for transition to vehicle seat belt).
- Never Leave Child Unattended: Do not leave your child unattended in the car seat, even for short periods.
- Impact Protection: The car seat features advanced side impact protection. Ensure the seat is correctly positioned to maximize this feature.
- After an Accident: If the car seat has been involved in an accident, even a minor one, it must be replaced immediately as its structural integrity may be compromised.
Product Features
The tectake i-Size Car Seat offers a range of features designed for safety, comfort, and convenience:
- i-Size Certified: Conforms to ECE R129 standards with integrated side impact protection.
- ISOFIX and Top Tether: Provides a secure and stable connection to the vehicle chassis.
- 360° Rotation: Allows easy access for placing and removing your child, and switching between forward and rear-facing positions (where applicable for child's height/age).
- Adjustable Recline: Two adjustable recline angles for optimal comfort during travel.
- Height-Adjustable Headrest: Adapts to your child's growth from 40 cm to 150 cm.
- 5-Point Safety Harness: Secure and adjustable harness for younger children.
- Thick Padding: Ensures high levels of comfort for long journeys.
- Removable and Washable Cover: Easy to clean and maintain hygiene.
Image: Overview of the tectake i-Size Car Seat highlighting key features such as i-Size certification, 360° rotation, 5-point harness, adjustable headrest, and washable cover. A child dummy is shown secured in the seat.
Image: Two tectake i-Size Car Seats, one configured for a younger child and one for an older child, illustrating the seat's adaptability as the child grows up to 36 kg.
Setup and Installation
Follow these steps for secure installation of your tectake i-Size Car Seat:
- Prepare the Vehicle: Ensure your vehicle has ISOFIX anchor points and a Top Tether attachment point. Locate these points in your car.
- Extend ISOFIX Connectors: Press the release buttons on the car seat to extend the ISOFIX connectors.
- Attach ISOFIX: Align the ISOFIX connectors with the vehicle's ISOFIX anchor points. Push firmly until you hear an audible "click" and the indicators turn green (if present). Pull on the seat to ensure it is securely attached.
- Connect Top Tether: Route the Top Tether strap over the back of the vehicle seat and attach the hook to the designated Top Tether anchor point in your vehicle. Pull the strap to tighten it, removing any slack, until the indicator turns green (if present).
- Check Stability: Once installed, firmly push and pull the car seat to ensure it is stable and does not move excessively.
- Adjust for Child: For younger children (40-105 cm), ensure the seat is in the rear-facing position (if applicable for your model's rotation feature) and use the 5-point harness. For older children (100-150 cm), the 5-point harness may be removed, and the child secured with the vehicle's 3-point seat belt. Adjust the headrest to the correct height.
Image: Close-up showing the reliable ISOFIX system ensuring secure anchoring and the robust Top Tether reducing forward movement in case of impact.
Image: Visual guide demonstrating the ISOFIX connection, the Top Tether attachment point behind the vehicle seat, and the proper use of the 5-point harness.
Operating Instructions
Securing Your Child with the 5-Point Harness (40-105 cm)
- Place Child: Open the harness buckle and place your child in the car seat.
- Fasten Harness: Bring the two buckle tongues together and insert them into the buckle until you hear a "click".
- Tighten Harness: Pull the adjustment strap at the front of the seat to tighten the harness until it is snug against your child's body. Ensure you can only fit one finger between the harness and your child's collarbone.
- Loosen Harness: Press the harness release button (usually located near the adjustment strap) and pull the shoulder straps outwards to loosen.
Adjusting the Headrest
The headrest can be adjusted to multiple positions to accommodate your child's height. Locate the headrest adjustment lever (usually at the top or back of the headrest). Squeeze the lever and slide the headrest up or down until it is at the correct height, ensuring the shoulder straps are at or just below your child's shoulders when rear-facing, or at or just above when forward-facing.
Image: The adjustable headrest, designed to adapt for children from 40 cm to 150 cm, shown with an arrow indicating upward adjustment.
Using the 360° Rotation Feature
To rotate the car seat, locate the rotation release lever (typically at the front base of the seat). Press or pull the lever and rotate the seat to the desired position (e.g., facing the car door for easy access, or switching between rear-facing and forward-facing). Ensure the seat locks securely into place after rotation.
Image: Visual representation of the smooth 360° swivel mechanism and adjustable recline positions of the car seat.
Adjusting Recline Angles
The car seat offers two recline angles for your child's comfort. Locate the recline adjustment handle (usually at the front or side of the base). Pull the handle and tilt the seat to the desired recline position. Release the handle to lock the seat in place.
Maintenance
Regular maintenance ensures the longevity and hygiene of your car seat:
- Cleaning the Cover: The polyester cover is completely removable and washable. Follow the washing instructions on the care label (typically cold water, gentle cycle, air dry). Do not tumble dry or iron.
- Cleaning the Shell: Wipe the plastic parts of the car seat shell with a damp cloth and mild soap. Do not use abrasive cleaners or solvents.
- Harness Care: Inspect the harness straps regularly for wear and tear. Clean with a damp cloth and mild soap. Do not machine wash the harness straps as this can weaken them.
- Storage: When not in use, store the car seat in a clean, dry place away from direct sunlight and extreme temperatures.
Troubleshooting
If you encounter issues with your tectake i-Size Car Seat, consider the following:
- Seat Feels Loose After Installation:
- Ensure ISOFIX connectors are fully engaged and indicators are green.
- Tighten the Top Tether strap securely.
- Push the car seat firmly into the vehicle seat back.
- Harness is Difficult to Tighten/Loosen:
- Check for any twists in the harness straps.
- Ensure no fabric is obstructing the adjustment mechanism.
- Clean the harness buckle if it feels sticky.
- Seat Does Not Rotate Smoothly:
- Ensure the rotation release lever is fully engaged.
- Check for any obstructions under the seat base.
If problems persist, please contact tectake customer support.
Specifications
| Feature | Detail |
|---|---|
| Brand | tectake |
| Installation Type | ISOFIX |
| Material | HDPE, 100% Polyester |
| Orientation | 360° Rotation |
| Product Dimensions (L x W x H) | 55P x 48l x 74H cm (approx. 55 x 48 x 74 cm) |
| Item Weight | 11.1 kg |
| Recommended Maximum Weight | 36 kg |
| Child Height Range | 40 cm to 150 cm |
| Certification | ECE R129 (i-Size) |
Image: Detailed product information including total measurements (48 x 55 x 66 - 74 cm), seat surface (25 x 29 cm), backrest height (46 cm), and technical data such as child height range (40-150 cm), maximum weight (36 kg), and materials (HDPE, steel, 100% polyester). All measurements are approximate.
Warranty and Support
For warranty information, product support, or to report any issues, please refer to the warranty card included with your purchase or visit the official tectake website. Keep your proof of purchase for warranty claims.
Contact Information: Please refer to the contact details provided in the packaging or on the official tectake website for customer service.
