AIKE Wall Mount Automatic Foam Soap Dispenser

Introduction

Thank you for choosing the AIKE AK1205FA Wall Mount Automatic Foam Soap Dispenser. This manual provides essential information for the safe and efficient use of your new dispenser. Please read it thoroughly before installation and operation, and retain it for future reference.

This automatic foam soap dispenser is designed for hygienic and convenient handwashing, featuring a responsive sensor and adjustable foam output. It is suitable for various environments, including homes and commercial settings.

Image: The AIKE AK1205FA dispenser providing luxurious foam.

Product Features

• Gentle, Dense Foam: Provides effective handwashing. Note: Not recommended for dilution or regular liquid soap. Use only foaming soap.
• Flexible Mounting Options: Supports both screw mounting and nail-free glue installation.
• Responsive Sensor: Delivers foam instantly without physical contact, promoting hygiene.
• 5-Level Adjustable Dispensing: Allows precise control over foam volume to reduce waste.
• Battery Powered: Operates on 4 AA batteries (not included).
• Waterproof Coil: Ensures stable sensing performance in humid environments.
• Dual-Purpose Key: Used to lock the unit and remove the foaming nozzle for cleaning.

Setup and Installation

Before installation, ensure the mounting surface is clean, dry, and flat. The required installation height is greater than 10 inches (25 cm) above the countertop or sink.

Package Contents:

• Dispenser x1
• Manual x1
• Nail-free Glue x1
• Screw x3
• Mounting Plate x1
• Wall Anchor x3
• Multi-functional Key x1
• Safety Screw x1

Image: Contents included with the AIKE AK1205FA dispenser.

Mounting Options:

1. Screw Mount:

   This method is suitable for most wall types and provides a secure, permanent installation.

   • Position the mounting plate on the desired wall location, ensuring it is at least 10 inches (25 cm) above the sink.
   • Mark the drill holes through the mounting plate.
   • Drill holes and insert wall anchors.
   • Secure the mounting plate to the wall using the provided screws.
   • Slide the dispenser onto the mounting plate until it clicks into place.
2. Nail-Free Glue Mount:

   This option is for clean, dry, and flat walls only. Allow 48+ hours for fixation before use.

   • Apply the nail-free glue to the back of the mounting plate in a zigzag pattern.
   • Press the mounting plate firmly against the desired wall location, ensuring it is at least 10 inches (25 cm) above the sink.
   • Hold in place for a few minutes or use temporary tape to secure it.
   • Wait at least 48 hours for the glue to fully cure before attaching the dispenser.
   • Slide the dispenser onto the mounting plate.

Image: Installation tips for screw mount and nail-free glue.

Battery Installation:

The dispenser requires 4 AA batteries (not included).

1. Use the multi-functional key to unlock the top cover of the dispenser.
2. Locate the battery compartment at the bottom of the dispenser.
3. Insert 4 AA batteries, ensuring correct polarity (+/-).
4. Close the battery compartment cover securely.

Filling the Dispenser:

The dispenser has a liquid volume capacity of 750 milliliters (25 OZ).

1. Unlock the top cover using the multi-functional key.
2. Pour foaming soap directly into the reservoir. Do not overfill.
3. Securely close and lock the top cover.

Operating Instructions

Automatic Dispensing:

The dispenser features a responsive infrared sensor for touchless operation.

• Place your hand approximately 2-3 inches (5-7 cm) below the dispensing nozzle.
• The sensor will detect your hand and dispense a pre-set amount of foam.
• Remove your hand once the foam is dispensed.

Image: Smart responsiveness for effortless dispensing.

Adjusting Foam Volume (5 Levels):

The dispenser allows you to adjust the amount of foam dispensed to suit your preference and conserve soap.

1. Locate the adjustment button, usually near the sensor or on the top panel.
2. Press the button repeatedly to cycle through the 5 dispensing levels. Each press will change the volume.
3. Test the dispensed amount by placing your hand under the sensor after each adjustment until the desired volume is achieved.

Image: 5-Level adjustable foam dispensing.

Foaming Effect Demonstration:

Watch this video for a demonstration of the foaming effect and adjustable levels.

Maintenance

Cleaning the Foaming Nozzle:

Regular cleaning of the nozzle ensures consistent foam quality and prevents blockages.

1. Use the multi-functional key to unlock the dispenser and remove the top cover.
2. Twist the foaming nozzle counter-clockwise to remove it from the dispenser.
3. Rinse the nozzle thoroughly under running water to clear any soap residue.
4. Ensure the nozzle is completely dry before reattaching.
5. Reattach the nozzle by twisting it clockwise until secure.
6. Close and lock the top cover.

Image: Steps for cleaning the foaming nozzle.

General Cleaning:

Wipe the exterior of the dispenser with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the finish.

Troubleshooting

Specifications

Image: Size comparison of the dispenser with a smartphone.

Warranty and Support

AIKE provides a 1-year support period for this product. For any inquiries, technical assistance, or warranty claims, please contact AIKE's dedicated service team. Refer to the contact information provided with your purchase or visit the official AIKE website for support details.

AIKE has over 30 years of expertise in manufacturing high-quality products, ensuring reliable service and support for our customers.