Manuals+

Junsun 2G+64G Car Stereo Radio

Junsun 2G+64G Car Stereo Radio for Dodge Ram 1500 2500 3500 (2013-2019) - Instruction Manual

Model: 2G+64G Car Stereo Radio

Introduction

Thank you for choosing the Junsun 2G+64G Car Stereo Radio. This manual provides essential information for the proper installation, operation, and maintenance of your new car stereo. Designed for Dodge Ram 1500, 2500, and 3500 models from 2013 to 2019, this unit features a 9-inch IPS HD touchscreen, wireless/wired CarPlay and Android Auto, 5G WiFi, Bluetooth 5.0, GPS navigation, steering wheel control (SWC), DSP, and AM/FM radio. Please read this manual thoroughly before use to ensure optimal performance and safety.

Safety Information

Package Contents

Please verify that all items listed below are included in your package:

Junsun Car Stereo Package Contents
Image: All components included in the Junsun 2G+64G Car Stereo Radio package.

Setup and Installation

The installation process involves removing the original factory radio and fascia, connecting the new head unit, and securing it in place. It is a plug-and-play design, but careful attention to detail is required.

1. Removing the Original Unit

  1. Remove Top Dash Panel: Use the provided crowbar tool to gently pry up and remove the top dash panel above the factory radio. This panel is typically held by clips.
  2. Unscrew Top Screws: Once the top panel is removed, locate and unscrew the two screws securing the top of the factory radio assembly.
  3. Remove Side Panels: Carefully pry off the side trim panels of the radio assembly. These are also typically held by clips.
  4. Unscrew Main Unit: Locate and unscrew the main bolts/screws holding the factory radio unit in place. There are usually four larger bolts.
  5. Disconnect Cables: Gently pull the factory radio unit forward and disconnect all electrical connectors from the back. Be careful not to damage any wires or connectors.

2. Installing the New Junsun Unit

  1. Prepare New Unit: The Junsun head unit comes pre-installed in a new fascia designed for your Dodge Ram.
  2. Connect Wiring Harness: Connect the provided main wiring harness to the corresponding ports on the back of the Junsun head unit.
  3. Connect CANBUS Decoder: Connect the CANBUS decoder to the main wiring harness. This is crucial for retaining steering wheel controls and other vehicle data.
  4. Connect GPS Antenna: Connect the GPS antenna to the designated port on the head unit. Route the antenna cable to a location on the dashboard or A-pillar with a clear view of the sky for optimal signal reception.
  5. Connect USB Cables: Connect the two USB cables. These can be routed to the glove compartment or a custom-drilled hole for easy access.
  6. Connect External Microphone: Connect the external microphone for improved call quality. Route it to a suitable location, such as near the rearview mirror or on the A-pillar.
  7. Connect Rearview Camera (Optional): If installing an aftermarket rearview camera, connect its RCA cable to the 'Rear CAM In' port on the head unit. Ensure the reverse trigger wire is connected to the vehicle's reverse light signal.
  8. Connect Original Vehicle Connectors: Connect the new wiring harness to the original vehicle connectors that were previously attached to the factory radio.
  9. Test Functionality: Before fully reassembling, turn on the vehicle and test all functions of the new stereo: power, audio, CarPlay/Android Auto, Bluetooth, GPS, steering wheel controls, and rearview camera.
  10. Secure New Unit: Carefully slide the new head unit assembly into the dashboard opening. Secure it with the screws removed earlier.
  11. Reinstall Panels: Reattach the side trim panels and the top dash panel, ensuring all clips snap securely into place.
Before and After Junsun Car Stereo Installation
Image: Comparison of the dashboard before and after installing the Junsun Car Stereo.
Junsun Car Stereo Wiring Diagram
Image: Detailed wiring connections for the Junsun Car Stereo.

Installation Videos

Video: Installation guide for Dodge Ram 2013-2019 Aftermarket Radio. This video demonstrates the step-by-step process of removing the old unit and installing the new one.

Video: Installation video specifically for Dodge Ram radio with Auto AC. Provides visual instructions for the installation process.

Operating Instructions

1. Wireless/Wired CarPlay & Android Auto

Junsun Car Stereo CarPlay and Android Auto Interface
Image: User interface showing CarPlay and Android Auto functionality.

2. GPS Navigation

Junsun Car Stereo GPS Navigation
Image: GPS navigation interface displaying map and route information.

3. Steering Wheel Control (SWC)

Junsun Car Stereo Steering Wheel Control Interface
Image: On-screen display for programming and using steering wheel controls.

4. Bluetooth 5.0

5. AM/FM Radio

6. Digital Sound Processor (DSP)

7. Rearview Camera

Junsun Car Stereo Rearview Camera Display
Image: Rearview camera display with parking guidelines.

8. Split Screen Function

9. 5GHz WiFi Connectivity

Operating Videos

Video: Demonstration of various features including reverse camera, voice commands, navigation, DSP, and video playback on the car stereo.

Maintenance

Troubleshooting

IssueSolution
Android Auto shows loading but can't connectEnsure your phone's WiFi is on. If your phone's Android version is higher than supported, contact customer support for an update method.
Steering Wheel Controls not workingEnsure the CANBUS TX/RX cables are correctly connected. Incorrect connection will prevent SWC functionality.
Loss of reverse warning or turn signal toneEnsure the external speaker is connected. If not connected, these warning tones may disappear.

Specifications

Warranty and Support

Your Junsun Car Stereo Radio comes with a 1-year manufacturer's warranty. For any inquiries, technical assistance, or issues, please contact our professional after-sales support team. They are available 24/7 to provide quick responses and product knowledge assistance.

Contact Support: Junsun-US@outlook.com