Bellemave Twin XL Over Queen Bunk Bed Instruction Manual

1. Introduction

Thank you for choosing the Bellemave Twin XL Over Queen Bunk Bed. This manual provides essential information for the safe assembly, proper use, and maintenance of your new bunk bed. Please read these instructions thoroughly before beginning assembly and retain them for future reference. For assistance, please contact Bellemave customer support.

Image 1.1: Assembled Bellemave Twin XL Over Queen Bunk Bed.

2. Safety Information

Your safety is paramount. Adhere to all warnings and instructions to prevent injury. Failure to follow these guidelines may result in serious injury.

• Weight Limits: Do not exceed the weight limit of 300 pounds for the upper bed and 600 pounds for the bottom bed.
• Guardrails: Always use the guardrail on the upper bed to prevent falls. Ensure guardrails are securely fastened.
• Ladder Safety: Use the ladder for entry and exit from the upper bunk. Ensure the ladder is stable before use.
• Mattress Thickness: The maximum mattress thickness for the upper bunk should not exceed 6 inches to ensure adequate guardrail height.
• Age Restriction: The upper bunk is not suitable for children under 6 years of age.
• Assembly: This product requires assembly. Ensure all parts are correctly installed and tightened before use. Periodically check and tighten all connections.
• Ventilation: Do not attach or hang items to any part of the bunk bed that are not designed for use with the bed, for example, but not limited to, hooks, belts, or jump ropes.
• Location: Place the bunk bed on a level surface.

3. Package Contents

Before assembly, verify that all components are present and undamaged. If any parts are missing or damaged, do not proceed with assembly. Contact Bellemave customer support for replacement parts.

Included Components:

• Headboards and Footboards (Upper and Lower)
• Side Rails (Upper and Lower)
• Support Slats (for both Twin XL and Queen beds)
• Guardrails (for upper bunk)
• Ladders (2 included)
• Center Support Legs (for bottom bed reinforcement)
• Assembly Hardware (bolts, nuts, washers, Allen wrenches)

Note: Mattresses are not included.

4. Setup and Assembly Instructions

Assembly typically requires two adults. Please follow the steps carefully. Do not fully tighten bolts until instructed.

1. Unpack and Identify Parts: Lay out all components on a soft, clean surface to prevent scratches. Compare each part to the provided parts list in your separate assembly diagram to ensure everything is present.
2. Assemble Lower Bed Frame: Attach the side rails to the headboard and footboard of the Queen-sized lower bed. Secure with the provided hardware, but do not fully tighten.
3. Install Lower Bed Slats: Place the Queen-sized support slats onto the lower bed frame. Ensure they are evenly spaced and secured according to the assembly diagram. Install the two extra middle thicker legs for reinforcement.
4. Assemble Upper Bed Frame: Attach the side rails to the headboard and footboard of the Twin XL-sized upper bed. Secure with hardware, leaving bolts slightly loose.
5. Install Upper Bed Slats: Place the Twin XL-sized support slats onto the upper bed frame. Ensure even spacing and secure attachment.
6. Attach Guardrails: Secure the guardrails to the upper bunk frame as indicated in the assembly diagram.
7. Connect Upper and Lower Frames: Carefully lift the assembled upper bunk and align it with the designated connection points on the lower bunk frame. Secure with the appropriate hardware. This step typically requires two people.
8. Attach Ladders: Secure both ladders to the bunk bed frame. Ensure they are firmly attached and stable.
9. Final Tightening: Once all components are in place and aligned, systematically tighten all bolts and screws using the provided Allen wrenches. Do not overtighten.

Image 4.1: Bunk bed frame prior to slat installation.

Image 4.2: Bunk bed frame with metal slats installed.

5. Operating Instructions (Usage)

• Mattress Placement: Place a Twin XL mattress on the upper bunk and a Queen mattress on the lower bunk. Ensure mattresses fit snugly within the frame.
• Ladder Use: Always use the provided ladders to access the upper bunk. Do not jump onto or off the bunk bed.
• Under-Bed Storage: The 9.4 inches of height space under the bed can be utilized for storage. Use storage bins or containers to keep items organized.
• Weight Distribution: Distribute weight evenly on both bunks. Avoid concentrating weight in one area.

6. Maintenance

• Cleaning: Wipe the metal frame with a soft, damp cloth. Avoid abrasive cleaners or harsh chemicals that could damage the finish.
• Hardware Check: Periodically (e.g., every 3-6 months) inspect all bolts, screws, and connections. Tighten any loose hardware to maintain stability and safety.
• Structural Integrity: Regularly check for any signs of wear, damage, or bending in the metal frame or slats. Discontinue use if any structural damage is observed and contact customer support.

7. Troubleshooting

8. Specifications

• Model: FST00067-T-AK1
• Size: Twin XL over Queen
• Product Dimensions (L x W x H): 82.7" x 63" x 64.6"
• Upper Bed Weight Capacity: 300 lbs
• Bottom Bed Weight Capacity: 600 lbs
• Under Bed Storage Height: 9.4 inches
• Material: Heavy Duty Metal
• Color: White
• Assembly Required: Yes
• Compatible Mattress Sizes: Twin XL (upper), Queen (lower)

Image 8.1: Detailed dimensions of the bunk bed.

9. Warranty and Support

Bellemave stands behind the quality of its products. For specific warranty details, please refer to the warranty card included with your purchase or visit the official Bellemave website. If you have any questions, require replacement parts, or need assistance with assembly or troubleshooting, please contact Bellemave customer support through the retailer where the product was purchased or via the contact information provided on the Bellemave website.

Online Support: Visit the Bellemave Store on Amazon