Introduction
Thank you for choosing the EZ EAR 2M Type C IEM Cable and KZ EDX PRO Wired Earbuds. This manual provides essential information for the proper setup, operation, and maintenance of your audio equipment. Please read this manual thoroughly before use to ensure optimal performance and longevity of your product.
Product Overview
The EZ EAR 2M Type C IEM Cable is designed to provide a high-quality audio connection for In-Ear Monitors (IEMs) with 2-pin connectors, featuring a USB-C termination for broad compatibility with modern devices. The KZ EDX PRO Wired Earbuds are equipped with a 10mm dual magnetic circuit dynamic driver, engineered for enhanced bass and clear audio reproduction.
Image: The EZ EAR 2M Type C IEM Cable, showcasing its USB-C connector, inline remote with volume and playback controls, and the detachable 2-pin connectors for IEMs.
Image: A pair of KZ EDX PRO Wired Earbuds, featuring their ergonomic design and gold-colored accents.
Setup
1. Connecting the Cable to the Earbuds
- Identify the 2-pin connectors on the EZ EAR cable and the corresponding sockets on the KZ EDX PRO earbuds. Ensure correct orientation (usually marked L for left and R for right, or with a small dot/indentation).
- Gently align the pins of the cable connector with the sockets on the earbud.
- Push firmly but carefully until the connectors are securely seated. Do not force the connection.
2. Connecting to an Audio Source
- Locate the USB-C port on your audio device (e.g., smartphone, tablet, computer).
- Insert the USB-C plug of the EZ EAR cable into the device's USB-C port.
- Ensure the connection is firm. Your device should recognize the earbuds as an audio output device.
Operation
Wearing the Earbuds
- Insert the earbuds into your ears, ensuring a comfortable and secure fit. The cable is designed to loop over the ear for stability.
- Experiment with different ear tip sizes (if provided separately) to achieve the best seal for optimal sound quality and bass response.
Image: A person wearing the KZ EDX PRO earbuds, demonstrating the over-ear cable routing for a secure fit.
Using Inline Controls
The EZ EAR cable features an inline remote control for convenient audio management:
- Volume Up (+): Press to increase audio volume.
- Volume Down (-): Press to decrease audio volume.
- Multi-function Button (Center):
- Single press: Play/Pause audio, Answer/End call.
- Double press: Skip to next track.
- Triple press: Go to previous track.
- Long press: Activate voice assistant (device dependent).
Audio Performance
The KZ EDX PRO earbuds are designed to deliver HIFI bass sound with a strong low-frequency density, rich texture, and powerful bass, thanks to their 10mm dual magnetic circuit dynamic driver. Ensure a proper earbud seal for the best audio experience.
Maintenance and Care
- Cleaning: Regularly wipe the earbuds and cable with a soft, dry cloth. For ear tips, remove them and clean with mild soap and water, then dry completely before reattaching.
- Storage: When not in use, store the earbuds and cable in a clean, dry place, preferably in a protective case, to prevent tangling and damage.
- Cable Care: Avoid sharp bends or excessive pulling on the cable, especially near connectors, to prevent internal wire damage. The cable's protective coating helps reduce noise from contact.
- Moisture: Keep the product away from excessive moisture and liquids.
Troubleshooting
- No Sound:
- Ensure the USB-C cable is fully inserted into your device.
- Check that the 2-pin connectors are securely attached to the earbuds.
- Verify your device's volume is not muted or set too low.
- Test with another audio source or device to rule out device-specific issues.
- Poor Sound Quality / Lack of Bass:
- Ensure the earbuds are properly seated in your ears, forming a good seal. Try different ear tip sizes if available.
- Check for any debris or earwax blocking the earbud nozzles.
- Inline Controls Not Responding:
- Ensure the cable is fully connected to your device.
- Some functions may be device-dependent. Check your device's settings.
Specifications
| Product Name | EZ EAR 2M Type C IEM Cable & KZ EDX PRO Wired Earbuds |
| Cable Length | 2 meters (2M) |
| Cable Connector (Source) | USB Type-C |
| Cable Connector (IEM) | 2-pin (QDC compatible) |
| Cable Material | High-quality, lightweight, pliable wire with protective coating |
| Earbud Driver | 10mm Dual magnetic circuit dynamic driver |
| Sound Characteristics | HIFI Bass Sound, enhanced low-frequency density, rich texture |
| Earbud Design | Resin inlaid metal technology, ergonomic |
| Compatibility | iPhone 15/16 series, all devices with USB-C interface |
| ASIN | B0F99SZX41 |
| First Available | April 10, 2025 |
Image: An exploded diagram of the KZ EDX PRO earbud, illustrating its internal structure and highlighting upgrades to appearance, cable interface, and configuration.
Safety Information
- Avoid listening at high volume levels for extended periods to prevent hearing damage.
- Do not use the earbuds in situations where inability to hear ambient sounds could be dangerous (e.g., driving, cycling, walking in traffic).
- Keep out of reach of children and pets. Small parts may pose a choking hazard.
- Do not attempt to disassemble or modify the product. This may void any potential warranty and cause damage.
Warranty and Support
Specific warranty information for this product is not provided within this manual. For details regarding warranty coverage, technical support, or service inquiries, please refer to the product packaging or contact the EZ EAR customer support directly through their official website or the retailer from whom the product was purchased.
