Roborock Q7 TF Robot Vacuum Cleaner User Manual

1. Introduction

The Roborock Q7 TF is an advanced robot vacuum cleaner designed to provide efficient and thorough cleaning for various floor types. It integrates powerful suction, intelligent navigation, and mopping capabilities to maintain a clean living environment. This manual provides instructions for setting up, operating, and maintaining your device.

Key Features:

• 10,000 Pa HyperForce Suction: Delivers powerful cleaning for dust and debris removal.
• Dual Anti-Tangle System: Designed to minimize hair tangles, suitable for homes with pets.
• Integrated Water Tank: 270ml capacity for continuous wet mopping.
• Three Adjustable Water Flow Levels: Allows customization of mopping intensity.
• Precise LiDAR Navigation: 360° scanning for accurate mapping and efficient route planning.
• Multi-Level Mapping: Supports mapping for up to three different floor levels.
• Scheduled Cleaning: Enables automated cleaning at specified times.

2. Safety Information

Before using this product, please read this user manual carefully and keep it for future reference. Failure to follow these instructions may result in electric shock, fire, or serious injury.

• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children should be supervised to ensure that they do not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• Do not use the robot in environments with open flames or fragile objects.
• Ensure the charging dock is placed on a level surface against a wall, with adequate clearance around it.
• Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
• Use only the manufacturer-specified power adapter and charging dock.
• Do not use the robot to pick up large objects, sharp objects, or liquids.
• Always remove the water tank and empty the dustbin before performing maintenance.

3. Package Contents

Verify that all components are present in the package:

• Roborock Q7 TF Robot Vacuum Cleaner
• Charging Dock
• Power Cable (2-pin EU plug)
• Water Tank (integrated)
• Floor Brush (main brush)
• Dusting Brush (side brush)
• User Manual

4. Product Overview

Robot Vacuum

The Roborock Q7 TF robot vacuum cleaner shown alongside its compact charging dock, ready for operation.

• LIDAR Sensor: For navigation and mapping.
• Power/Clean Button: Start/pause cleaning, power on/off.
• Dock Button: Send robot back to charging dock.
• Dustbin & Water Tank: Integrated unit for dust collection and water storage.
• Main Brush: For deep cleaning carpets and hard floors.
• Side Brush: Sweeps debris from edges and corners.
• Cliff Sensors: Detects drops to prevent falls.
• Charging Contacts: Connects with the charging dock.

Charging Dock

• Charging Contacts: Transfers power to the robot.
• Power Indicator: Shows charging status.
• Dustbag Compartment: For automatic dust emptying (if applicable model).

5. Setup

5.1 Charging Dock Placement

1. Place the charging dock on a hard, level surface against a wall.
2. Ensure there is at least 0.5 meters (1.6 feet) of clear space on both sides and 1.5 meters (4.9 feet) in front of the dock.
3. Keep the area free from obstacles, such as power cables or furniture.

5.2 Power Connection

1. Connect the power cable to the charging dock.
2. Plug the other end of the power cable into a wall outlet.

5.3 Initial Charge

1. Place the robot on the charging dock. Ensure the charging contacts on the robot align with those on the dock.
2. The robot will power on automatically and begin charging. Allow the robot to fully charge before its first use.

5.4 App Download and Connection

1. Download the Roborock app from your mobile device's app store (iOS or Android).
2. Open the app and follow the on-screen instructions to create an account and add your Roborock Q7 TF.
3. Ensure your Wi-Fi network is 2.4GHz for optimal connection.

5.5 Water Tank Filling (for Mopping)

1. Remove the integrated dustbin and water tank unit from the robot.
2. Open the water tank cap and fill it with clean water. Do not use detergents or cleaning solutions not approved by Roborock.
3. Close the cap securely and reinsert the unit into the robot.

A detailed view of the integrated 270ml water tank within the Roborock Q7 TF, designed for continuous mopping.

6. Operating Instructions

6.1 Starting/Pausing/Stopping Cleaning

• Start Cleaning: Press the Power/Clean button on the robot or use the Roborock app. The robot will begin cleaning the entire area.
• Pause Cleaning: Press the Power/Clean button during operation.
• Stop Cleaning: Press and hold the Power/Clean button for 3 seconds, or use the app to send the robot back to the dock.

6.2 Mopping Function

The Roborock Q7 TF can vacuum and mop simultaneously. Ensure the water tank is filled and the mop cloth is attached (if applicable).

A visual representation of the three adjustable water flow levels for the mopping function, allowing customization of cleaning intensity.

• Adjust water flow levels (low, medium, high) via the Roborock app to suit different floor types and cleaning needs.
• Remove the mop cloth after cleaning to prevent mildew and odors.

6.3 Scheduled Cleaning

Set up cleaning schedules through the Roborock app. You can specify cleaning times, days, and areas.

An image depicting the Roborock Q7 TF being controlled via a smartphone app for scheduled cleaning, alongside an illustration of its multi-level mapping capability for up to three floors.

6.4 Using the App (Mapping, No-Go Zones, etc.)

An overhead view showing the Roborock Q7 TF utilizing its LiDAR navigation system to scan a room and create a detailed map for efficient cleaning.

• Mapping: The robot creates a map of your home during its first cleaning run. This map can be viewed and edited in the app.
• Multi-Level Mapping: The app supports saving maps for up to three different floor levels.
• No-Go Zones & Invisible Walls: Define areas the robot should avoid or virtual barriers it should not cross.
• Zone Cleaning: Select specific areas on the map for the robot to clean.
• Custom Cleaning Modes: Adjust suction power and water flow for different rooms or areas.

7. Maintenance

Regular maintenance ensures optimal performance and extends the lifespan of your Roborock Q7 TF.

7.1 Dustbin and Filter

1. Empty Dustbin: Press the release button to remove the integrated dustbin/water tank unit. Open the dustbin lid and empty its contents into a trash bin.
2. Clean Filter: Remove the HEPA filter from the dustbin. Tap it gently to remove dust. Rinse the filter with water if necessary, but ensure it is completely dry before reinstallation (allow 24 hours).
3. Frequency: Empty dustbin after each use. Clean filter weekly. Replace filter every 3-6 months.

7.2 Main Brush

A cutaway view illustrating the dual anti-tangle brush system of the Roborock Q7 TF, designed to minimize hair entanglement during cleaning.

1. Flip the robot over and press the release tabs to remove the main brush cover.
2. Lift out the main brush. Use the cleaning tool (if provided) to remove hair and debris tangled around the brush.
3. Reinstall the main brush and cover.
4. Frequency: Clean weekly. Replace every 6-12 months.

7.3 Side Brush

1. Unscrew the side brush.
2. Remove any hair or debris wrapped around the brush or its axle.
3. Reattach the side brush.
4. Frequency: Clean monthly. Replace every 3-6 months.

7.4 Water Tank and Mop Cloth

1. Empty any remaining water from the tank after each mopping session.
2. Remove the mop cloth and rinse it thoroughly with water. Allow it to air dry completely.
3. Frequency: Clean mop cloth after each use.

7.5 Sensors and Charging Contacts

1. Wipe all sensors (cliff sensors, wall sensor, LiDAR sensor window) and charging contacts on both the robot and the dock with a soft, dry cloth.
2. Frequency: Clean monthly.

8. Troubleshooting

If you encounter issues with your Roborock Q7 TF, refer to the following table for common problems and solutions.

9. Specifications

10. Warranty and Support

The Roborock Q7 TF Robot Vacuum Cleaner comes with a two-year local warranty and service support available in Singapore. For warranty claims, technical assistance, or customer service inquiries, please contact your local Roborock authorized service center or refer to the official Roborock website for support information.

For more information, visit the Roborock Store on Amazon.sg.